• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.806-810
• /
• 2005

홍수로 인한 국민의 재산과 인명피해를 방지 또는 최소화하기 위한 방법으로 주요지점을 선정하여 홍수예보를 수행하고 있다. 이러한 홍수예보는 초기 강우법, 수위법 등의 단순한 방법으로 수행되었으나, 컴퓨터가 발달되면서 여러 형태의 홍수유출모형이 개발되어 현재에는 홍수유출모형을 이용한 홍수예보를 수행하고 있다. 낙동강홍수예보 시스템은 1987년 낙동강홍수통제소의 개소시 42개소의 수위관측소와 54개소의 우량관측소를 중심으로 43개 소유역을 구분하고 티센망을 구성하여 홍수예보시스템을 구축하였다. 홍수예보시스템이 구축된 후 여러 차례의 매개변수 개선과정을 거쳐 운용하고 있다. 반면, 지속적인 수문관측소의 증설이 이루어졌으나 이를 모형에 반영하지 않아 증설된 수위관측소를 반영하여 114개 소유역으로 구분하고 추가된 우량관측소를 이용하여 티센망을 구성하였으며, 당초 반영되지 않았던 소규모댐을 모형에 추가하여 예측의 정확도를 재고하였다. 증설된 수문관측소를 모형에 반영과 함께 우량자료의 신뢰성 및 안정성을 확보하기 위한 우량관측소의 확장방안을 제시하였다. 본 연구에서 수행한 낙동강홍수예보 시스템의 소유역을 114개로 나누고 기존의 유효우량산정법, 유역유출모형 하도유출모형의 매개변수를 전통적인 방법으로 재산정하여 홍수기에 적용한 결과 당초의 홍수예보시스템으로 예측한 결과보다 소유역의 적절하게 재구성하는 것으로도 예측의 정밀도가 개선되었음을 확인할 수 있었다. 그러나, 소유역의 수와 하도의 수가 증가하면서 발생하는 오차를 감소시킬 필요성이 있으며, 이는 지속적인 시스템의 운용을 통하여 모형구성을 개선함으로서 어느 정도 개선될 것으로 판단된다. 그밖에 기존의 매개변수산정을 전통적인 방법에서 우리나라 하천 또는 낙동강유역의 하천에 적당한 방법을 개발하여 개선시킬 필요성이 있다.>$4.3\%$로 가장 근접한 결과를 나타내었으며, 총 유출량에서도 각각 $7.8\%,\;13.2\%$의 오차율을 가지는 것으로 분석되어 타 모형에 비해 실유량과의 차가 가장 적은 것으로 모의되었다. 향후 도시유출을 모의하는 데 가장 근사한 유출량을 산정할 수 있는 근거가 될 것이며, 도시재해 저감대책을 수립하는데 기여할 수 있을 것이라 판단된다.로 판단되는 대안들을 제시하는 예비타당성(Prefeasibility) 계획을 수립하였다. 이렇게 제시된 계획은 향후 과학적인 분석(세부평가방법)을 통해 대안을 평가하고 구체적인 타당성(feasibility) 계획을 수립하는데 토대가 될 것이다.{0.11R(mm)}(r^2=0.69)$로 나타났다. 이는 토양의 투수특성에 따라 강우량 증가에 비례하여 점증하는 침투수와 구분되는 현상이었다. 경사와 토양이 같은 조건에서 나지의 경우 역시 $Ro_{B10}(mm)=20.3e^{0.08R(mm)(r^2=0.84)$로 지수적으로 증가하는 경향을 나타내었다. 유거수량은 토성별로 양토를 1.0으로 기준할 때 사양토가 0.86으로 가장 작았고, 식양토 1.09, 식토 1.15로 평가되어 침투수에 비해 토성별 차이가 크게 나타났다. 이는 토성이 세립질일 수록 유거수의 저항이 작기 때문으로 생각된다. 경사에 따라서는 경사도가 증가할수록 증가하였으며 $10\% 경사일 때를 기준으로 $Ro(mm)=Ro_{10}{\times}0.797{\times}e^{-0.021s(\%)}$로 나타났다.천성 승모판 폐쇄 부전등을 초래하는 심각한 선천성 심질환이다. 그러나 진단 즉시 직접 좌관상동맥-대동맥 이식술로 수술적 교정을 해줌으로써 좋은 성적을 기대할 수 있음을 보

• Journal of the Korean Vacuum Society
• /
• v.16 no.1
• /
• pp.46-51
• /
• 2007

The HFMX((High Flux Macromolecular X-ray crystallography) beamline at Pohang Accelerator Laboratory uses beams from a multi-pole wiggler. Two horizontal and vertical slits relevant to high heat-load are installed at its front-end. In order to treat high heat-load with reducing beam scattering, the horizontal slit has two Glidcop blocks with a grazing incidence angle of $10^{\circ}$ of a grazing-incidence knife-edge configuration. The blocks adjust the slit gap by being translated along guides by two actuating bars, respectively. Water flowing through holes, drilled along the actuating bars, cools the heat-load of both blocks. The vortical slit has the same structure as the horizontal slit except its installation direction with respect to the vacuum chamber and its grazing incidence angle. By virtue of a pair of blocks translating on guides, no alignment between both blocks is required and the installed slits show stable operating performance. The cooling performance of the two slits has been also shown to be acceptable. In this paper, the detailed explanation for the design of the two slits is presented and their operating performance is discussed.

• The Journal of Engineering Geology
• /
• v.15 no.2 s.42
• /
• pp.185-199
• /
• 2005

Properties of sliding materials are dependent on the lithology because debris is the product of rock weathering processes. In order to characterize transportation behavior of debris dependent of debris types, this study selected 26 debris flows over three areas composed with different rock weathering types and topographic conditions. Analyses of lithology, weathering, and topographic characteristics were performed by detailed field survey. Based on the field survey data, transportation behavior of debris was studied at the aspect of the relationship of grain size and volume of debris as well as topographic conditions. According to the study results, change of slope angle is very influential factor on runout distance of debris among the topographic factors. Because the sliding velocity and the energy of debris are frequently changed and more irregular on an undulating slope, the unout distance of debris is larger than that of an uniformly dipping slope. Runout distance of debris is also influenced by volume and grain size of debris. Volume of debris in the gabbro is four or five times larger than that of the granite area because it is controlled by the lithology. Considered with grain size distribution, runout distance of debris is longer in the gabbro area which is composed with irregular grain size bearing large corestones than that in the medium grained granite area.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.3
• /
• pp.13-27
• /
• 2018

To study how stable the rubble mound breakwaters are, one can look to the research of wave induced seepage flow through the pores of the rubble mound. Seepage flow is generally generated by the difference between the water level around the breakwater during a typhoon. The existing stability analysis method of the rubble mound is the static analysis which simply considers the force equilibrium taking into account the horizontal force acting on the concrete block induced by a wave (calculated by Goda equation) and the vertical force induced by the weight inclusive of the concrete block, quarry run, filter, and armor layer above the slipping plane. However, this static method does not consider the wave-induced seepage flow in the rubble mound. Such seepage may decrease the stability of the rubble mound. The stability of a rubble mound breakwater under the action of seepage was studied based on the results of CFD software (OpenFOAM) and Limit Equilibrium Method (GeoStudio). The numerical analysis result showed that the seepage flow decreased the stability of the rubble mound breakwaters. The results of the numerical analyses also revealed the stability of the rubble mound was varied with time. Especially, the most critical state happened at the condition of overtopping the concrete block, acting strong uplift pressure raising along side and underneath the concrete block, and generating high pore pressure inside rubble mound due to seepage flow. Therefore, it may be necessary to conduct a dynamic analysis considering the effect of wave-induce seepage flow together with the static analysis.

• The Journal of Engineering Geology
• /
• v.25 no.3
• /
• pp.413-420
• /
• 2015

Streambed hydraulic conductivity along the upper reaches of the Gongdo stage of Anseong Stream was estimated through measurements of stream-aquifer exchange rates (using a seepage meter) and vertical hydraulic gradients (using a manually driven piezometer). From the measured data, it was found out that the stream-aquifer exchange rates varied from -1.55 × 10^-6 to 1.77 × 10^-5 m/s, the corresponding vertical hydraulic gradient varied from -0.122 to 0.030, and the values of the streambed vertical hydraulic conductivity were estimated from 1.77 × 10^-5 to 1.97 × 10^-3 m/s, with variations representing local differences. The results are within the general range of streambed hydraulic conductivity values suggested by Calver (2001) and are slightly higher than values previously measured at other stream sites in Korea. The combined use of a drive-point piezometer and seepage meter (both constructed of high-strength stainless steel) is expected to be of practical use in the estimation of streambed hydraulic conductance, given the durability and portability of the instruments.

• Journal of Wetlands Research
• /
• v.16 no.2
• /
• pp.173-185
• /
• 2014

Climate change has caused detrimental phenomena such as heavy rainfall which could aggravate soil erosion. Accordingly, it is needed to evaluate the groundwater recharge, baseflow, and soil erosion for the efficient management of water resources and quality. In this study, future climate change scenarios were applied to the H aean-myeon watershed which is a steep sloping watershed in South Korea to analyze groundwater recharge, baseflow, sediment. Also, the variation of groundwater recharge, baseflow, sediment was analyzed according to the change of slope (5 %). Simulated periods were divided into three terms (2013 ~ 2040 years, 2041 ~ 2070 years, 2071 ~ 2100 years). As a result of this study, average groundwater recharge and baseflow increased by 50 %, 42 %, and sediment decreased by 72 %, respectively. In these regards, the suggested method will positively contribute to hydro-ecosystem and reduction of muddy water at a steep sloping watershed.

• Journal of Korean Society of Forest Science
• /
• v.107 no.4
• /
• pp.385-392
• /
• 2018

The slope stabilization analysis was performed by conducting survey and selecting the representative section in order to improve slope composition and management technology of masonry embankments in the quarry area, The mean slope of the masonry retain wall (A, B, C, D, E, F) was $38.5^{\circ}$, although the steep slope of the lowest slope (A) as $59^{\circ}$. The horizontal distance of the masonry embankments is 66.2 m and the slope height is 48.3 m. However, the inclination of the masonry embankments is relatively steep and visually unstable. The slope stability analysis for the slope stability analysis was taken into account during the drying and saturation. The slope stability analysis during saturation was performed by modeling the fully saturated slope. The strength constants of the ground were divided into two groups. The safety factor for dry period was 1.850 and the safety factor for rainy season was 1.333. The safety rate of dry period and rainy season was above 1.5 and 1.2. However, the weathered granite on the upper part of the masonry embankments at the time of heavy rainfall is considered to have a high risk of slope erosion and collapse. Therefore, it is considered necessary to take measures for stabilization through appropriate maintenance such as drainage installation.

• The korean journal of orthodontics
• /
• v.29 no.2 s.73
• /
• pp.197-207
• /
• 1999

Although there is a severe underlying skeletal deformity, the dentition has often maintained some occlusal contact and interdigitation by the teeth compensating in their positions for the skeletal problem, and these dental compensations are manifested in all three planes of space. The purposes of present investigation were 1) to study the pattern of dentoalveolar compensation of hyperdivergent skeletal pattern , and 2) to compare the dentoalveolar compensations of hyperdivergent skeletal pattern in children with adults. The samples selected for this study were consisted of 60 subjects in normal group, 60 subjects in hyperdivergent group. Each was divided into two subgroups by age ; child groups($8\~12yr$ old) and adult groups(17yr old over). The findings of this study were as follows; 1. In child, hyperdivergent subjects had smaller posterior lower facial height(p<0.01) and slightly longer anterior lower facial height than normal ones. In adults, they still expressed smaller posterior lower facial height and much longer anterior lower facial height than normal ones(p<0.01). 2. Hyperdivergent subjects had larger amount of upper and lower incisor relative eruption to their basal bone length than normal ones(p<0.05). In adult, relative eruption of upper incisor was increasing(p<0.05), although relative eruption of lower incisor remained the same as the child. 3. In child, there was no difference between hyperdivergent group and nomal one in the upper and lower molar relative eruption to their basal bone length. In adult, hyperdivergent group had target amount of upper molar relative eruption than normal ones(p<0.01), but relative eruption of lower molar was similar to normal ones. 4. Hyperdivergent group had larger angle between lower occlusal plane and mandibular plane than normal group(p<0.01). Upper occlusal plane of adult groups rotated more antero-superiorly than child groups, and adult hyperdivergent group had sleeper upper occlusal plane than normal group(p<0.05).

• Economic and Environmental Geology
• /
• v.28 no.6
• /
• pp.579-585
• /
• 1995

The Samkwang mine is Cretaceous gold-silver-bearing deposits located in the western part of the Ogcheon belt The ore deposits have been emplaced within granite gneiss of the Precambrian age. The Au-Ag deposits are hydrothermal-vein type, characterized by arsenic-, gold- and silver-bearing sulphides, in addition to the principal ore-forming sulphides arsenopyrite, galena, sphalerite, chalcopyrite, pyrite and pyrrhotite. Their proven reserves are 355,000 MT, and grades are 8.4 g Au/t and 13.6 g Ag/t. On the basis of their structural characters, the Au-Ag-bearing quartz veins are classified into three types of ore veins; (1) The Main vein shows $N40^{\circ}-80^{\circ}E$ strike and $55^{\circ}-90^{\circ}SE$ dip, (2) the Sangban vein shows E-W strike and $30^{\circ}-40^{\circ}S$ dip, and (3) the Gukseong vein has $N25^{\circ}-40^{\circ}W$strike and $65^{\circ}-80^{\circ}SW$ dip. The emplacements of the ore veins are closely related to the minimum stress axis $({\sigma}_3)$ during the strike-slip movement of the study area. The ore-bearing veins filled with extension fractures during strike-slip movements were sequentially emplaced as follows: I) When ${\sigma}_1$ operates obliquely to NE-series discontinous surface, the Main fault zone $(F_1)$ developes. 2) During the same time, extension fractures ($T_1$ Gukseong veins) take place. 3) When the fault progress continuously, the existing $T_1$, may be high angle and $T_2$ (Daehung vein) developes continuously. 4) When ${\sigma}_1$ changes to sinistral sense, $T_3$ (basic dyke) occurs. 5) When a reverse fault becomes active, the Sangban vein is branched from the Guksabong vein.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.1
• /
• pp.31-38
• /
• 1999

Rainfall factor. R, and soil factor, K were estimated to use the Revised Universal Soil Loss Equation (RUSLE) to predict the amount of soil erosion from a land on slope in Kangwon-do, Korea. The average of R factor was 405 with a range from 251 to 601. The R factor differed among regions. The R factor at Taegwalryung, in the highland region, was 409 and those at Inje and Hongchon, in the mid mountainous regions, ranged from 310 to 493. The R factors at Wonju and Chuncheon, in the plain regions, ranged from 505 to 601. The R factors at Sokcho, Kangnung and Samchok, in the east coastal region, which ranged from 251 to 368, were lowee than those in the western part of the Taebaeg Mountains. The R factor during the winter including the effect of winter freezing and thawing was 12 to 30% of the annual average value in the east coastal and highland regions, while that in the western part of Taebaeg Mountains was lower than 7%. The average of K factor in the surface soil was 0.21 with a range from 0.06 to 0.42. The K factors of Odae and Weoljeong serieses were the lowest, while that of Imog was the highest. The average of K factor in the subsoil was 0.28 with a range from 0.07 to 0.45. The K factor of the subsoil was 1.3 times higher than that of top soil. The average of K factor in he soil including the effect of the gravel covering and percolation was 0.18 with a range from 0.03 to 0.33. In contrast. the K factor excluding the effect of the gravel covering was lower than this. The average of K factor in the frozen subsoil was 0.33, which was 1.6 times higher than that of the non frozen subsoil.