• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.377-385
• /
• 2015

The span-lengthening of PSC I girder has increased the risk of lateral instability of the girder with the increases in the aspect ratio and self-weight of the girder. Recently, collapses of PSC I girder during construction raise the necessity of evaluating the lateral instability of the girder. Thus, the present study evaluated the lateral behavior and instability of PSC I girders under wind load, regarded as one of the main causes of the roll-over collapse during construction. Lateral instability of the girder is mainly dependent on the length of the girder and the stiffness of the support. The analysis results of this study showed the decrease in the critical wind load and the increase in the critical deformation and angle of the girder, leading to the lateral instability of the girder. Finally, this study proposed analytical equations that can predict the critical amount of wind load and lateral deformation of the girder, which would provide quantitative management values to maintain lateral stability of PSC I girder during construction.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.6
• /
• pp.729-734
• /
• 2002

The effect of several simplified methods of seismic analysis is estimated. The pounding/contacting of superstructures were considered in the multispan simply supported bridge and the multispan continuous bridge. Although nonlinear time history analysis is generally used for seismic analysis of bridges, many codes including AASHTO propose several simplified analysis methods. AASHTO, however, does not mention pounding. Therefore, the simplified methods may produce results that are different from those of nonlinear time history analysis. This study developed nonlinear analytical models of the two types of bridges mentioned. The models were then modified to the simplified linear models for simplified analysis. The results of the simplified methods were compared with those of nonlinear time history analysis. It was found that including of the pounding/contacting element in the simplified methods generated responses similar to those of the nonlinear time history analysis.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.6
• /
• pp.701-710
• /
• 2012

We present optimum design for truss and frame structures subject to constraints on stresses, displacement, and natural frequency. The optimum design procedure is used discrete and continuous design variables and Genetic Algorithms. Genetic Algorithms is used the method of Elitism and penalty parameters in order to improved fitness in the reproduction process, and optimum design is used steel(W-section) and pre-made discrete cross-section. Truss and frame structures optimization examples are used for 10-Bar truss, 25-Bar truss, 1-bay 2-story frame, 1-bay 7-story frame, and these examples are employed to demonstrate the availability and serviceability of Genetic Algorithms for solving optimum design of truss and frame.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.41-44
• /
• 2008

The PCT that supports the walls of long span temporary shoring facility is previously manufactured in the way of prestressing, and it which is composed of concrete is improved precast structure to satisfy enough stiffness. The components of PCT are manufactured as a fixed form, and they are close to the inner side of the wall of temporary shoring facility by fixed means in PCT. PCT system as support structure is that the ends of concrete filled segment members are united by the means of connection and also they have connection hole. In this study, PCT has enough bearing power for the long span temporary shoring facility, and also make the term of work reduce due to that the time of curing reduce through the method of precast.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.139-150
• /
• 2005

Finite element method is applied to the determinations of the two eigenvalues(the elastic critical load and the natural frequence of lateral vibrations) of single story-3 equal bay rectangular frame. The analysis parameters are taper parameter ${\alpha}$ for column, and beam span to column height ratio, ${\beta}$ and second moment area ratio of beam to column, ${\Upsilon}$. Support condition at the column base and sway condition at the column top are also considered in the stability analysis of frame. The changes in the coefficient of eigenvalue are represented by algebraic function of analysis parameter. The coefficients estimated by the proposed algebraic function show good agreement with those determined by finite element method, which suggest the design aid role of the proposed function. By increasing the column axial forces step by step, the corresponding frequencies are also determined, which makes one examine or confirm the relationship suggested by other studies.

• Journal of the Korea Concrete Institute
• /
• v.15 no.3
• /
• pp.482-493
• /
• 2003

Flat plate structures subjected to lateral load have less deformability than conventional moment frames, due to the brittle failure of plate-column connection. In the present study, parametric study using nonlinear finite element analysis was performed to investigate the deformability of flat plates. The numerical results show that as number of continuous spans increases, the deformability of flat plates considerably decreases. Therefore, existing experiments using sub-assemblages with 1 or 2 spans may overestimate the deformability of flat plates, and current design provisions based on the experiments may not be accurate in estimating the deformability. A design method estimating the deformability was developed on the basis of numerical results, and verified by comparison with existing experiment. In the proposed method, the effects of primary design parameters such as direct shear force, punching shear capacity, aspect ratio of connection, number of spans, and initial stiffness of plate can be considered.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.04a
• /
• pp.335-340
• /
• 1998

The apparently different physical problems of lateral vibration and elastic stability of a linear member are limiting cases of a single phenomenon, the more general expression being the mode of vibration with end thrust. For a single-span beam-column, it is generally known that the square of the frequency of lateral vibration is approximately linearly related to compressive axial force. In this paper the relationship between the frequency and axial force of multi-span compression members is investigated by means of the finite element method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1065-1079
• /
• 2014

The ultimate behavior of reinforced concrete corbel is complicated due to the primary design variables including the shear span-to-effective depth ratio a/d, flexural reinforcement ratio, load condition, and material properties. In this study, a simple indeterminate strut-tie model reflecting all characteristics of the ultimate strength and complicated structural behavior is proposed for the design of the reinforced concrete corbels with shear span-to-effective depth ratio of $a/d{\leq}1$. A load distribution ratio, defined as the fraction of applied load transferred by horizontal truss mechanism, is also proposed to help structural designers perform the design of reinforced concrete corbels by using the strut-tie model approaches of current design codes. For the development of the load distribution ratio, numerous material nonlinear finite element analyses of the proposed indeterminate strut-tie model were conducted by changing primary design variables. The ultimate strengths of reinforced concrete corbels tested to failure were evaluated by incorporating the proposed strut-tie model and load distribution ratio into the ACI 318-11's strut-tie model method. The validity of the proposed model and load distribution ratio was examined by comparing the strength analysis results with those by the ACI 318-11's conventional design method and strut-tie model methods of current design codes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.534-544
• /
• 2019

Because the pile-bent of IPM Bridge is projected from the soil surface, excessive displacement of abutment can be induced. According to design guide of IPM Bridge, the shape of the bridges used in this study was applied to the maximum applicable 120.0m span, 30-degree for skew angle, and 10.0m for the protruded pile-bent height. The maximum displacement by the maximum span application condition of the IPM Bridge was calculated using this bridge model, and the safety of a horizontal displacement of the IPM Bridge was investigated based on the allowable displacement presented by Bozozuk. The maximum horizontal displacement of the IPM Bridge was calculated to be larger in the winter shrinkage condition than in the summer expansion condition, the horizontal displacements were more affected by the length of a bridge than by the skew angle. And the vertical displacement was not affected by the skew angle and length. As the span increases, the horizontal displacement increases significantly, the horizontal displacement at 120.0m span length was found to exceed the allowable displacement proposed by Bozozuk. However, the moment generated in the pile-bent did not exceed the plastic moment.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.34 no.2
• /
• pp.127-133
• /
• 1989

An experiment was conducted at the Yeongnam Crop Experiment Station to obtain basic informations about cultural techniques for high yield by manipulating plant spacing in association with seedling number. Cultivars showing relatively low competition index within or between rice hill were Palgongbyeo, Milyang 83. Milyang 90 and Sangpungbyeo, while those with high competition index were Pungsanbyeo, Samgangbyeo, Weongpungbyeo, Taebaegbyeo and Dongjinbyeo. Variations of agronomic characters such as culm length, spikelets per panicle, grain yield per panicle among each culm within hill were not interrelated among the characters. This phenomenon was also same within and between cultivar groups. However, cultivars having high competitive ability showed relatively low variation in agronomic characters. There was a trend that most of rice cultivars had a high positive correlation between total competition index and rice grain yield. Competition index between rice hill was more significant than that of within rice hill for Tongil type cultivars except Milyang 83 which belonged to low tillering capacity while both types of competition index within and between hill were important for Japonica type cultivars and Milyang 83 of Tongil type cultivar to increase rice yield.