• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1747-1751
• /
• 2003

The paper shows properties such as vickers hardness, yielding and ultimate stresses for the weld zone of the butt and the lap jointed specimens, and compare maximum loads, stress-strain curves, deformation appearance after guided bending test and fracture appearance for butt and lap jointed specimens. The research in this experiment also shows the weldability of the butt joint specimen is better than that of the lap joint specimen using FSW with $2mm^{t}$ aluminum alloy sheet in milling machine.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.31-31
• /
• 2009

최근 전세계적으로 유가상승 및 환경에 대한 관심이 증대되면서 자동차 업계에서는 차량 경량화를 통한 연비향상에 대한 연구가 활발히 진행되고 있다. 대표적인 기술개발 사례로서 초경량 철강 차체의 개발을 들 수 있다. 이는 고장력강을 적용함으로써 강성을 증대시킴과 동시에 두께감소에 의한 경량화를 이루고자 추진되고 있다. 하지만 고장력강은 자체의 높은 강성을 지니고 있는 반면, 일반 강종에 비해서 스프링백이 크고 용접성도 많이 떨어지는 제약을 안고 있다. 아크 용접법 중 하나인 AC pulse MIG 용접은 DCEP (direct current electrode positive) 와 DCEN (direct current electrode positive) 구간이 주기적으로 반복하는 용접법으로 스패터 발생이 거의 없으며 특히 갭 접합성이 우수하여 자동차 차체 조립공정에 적용되고 있다. 본 연구에서는 자동차 차체용 AHSS 소재의 겹치기 용접 실험을 통해 실제 생산라인에서 용접 이음부에 발생되는 갭에 대해 강건한 용접 공정 조건을 제시하였다. 먼저 고속카메라 촬영을 통해 AC pulse MIG 용접에서 EN ratio 변화에 따른 와이어 용융현상을 분석 하였으며 단면마크로, 인장시험, 인장 파단면 분석을 통해 겹치기 용접에서 0~2mm 사이의 갭 발생에 강건한 용접 조선을 제시하였다.

• 한국기계가공학회지
• /
• 제18권11호
• /
• pp.57-62
• /
• 2019

This paper describes the prediction of eigenfrequencies due to changes in stiffness and mass in the connection area of the lap joint beam in terms of linear and torsional stiffness as well as connection length. The sensitivities of mass and stiffness in the finite element model were derived by using the first-order differential and algebraic equation and were thereafter applied to obtain new natural frequencies that were compared with theoretical exact solutions. Newly predicted natural frequencies due to only a change in stiffness were in relatively good agreement with those in lower modes for rigid joints, while further investigation was needed for flexible joints. On the other hand, only the change in mass resulted in a large discrepancy in the flexible joint case. It may be strongly anticipated that this study will provide a useful tool for estimating modal parameters by change in any design variable, such as the structural dimension, material property, or connection type for a large-scale structure, even though the proposed methodology is currently limited to a jointed beam.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1294-1298
• /
• 2007

Welding process monitoring is advantageous for maintaining weld quality and numerous sensing techniques have been developed for laser welding. Coaxial image monitoring enables direct monitoring of the weld pool shape and keyhole behavior, but requires the complex optical system and the image processing technique. In this study, we coaxially acquired the weld pool images during laser lap welding by using the camera and special illumination. The welding characteristics - pool width and length, keyhole shape, etc - were extracted by using image processing and the relationship between these characteristics and the penetration depth were investigated.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.65-74
• /
• 1995

The weld seam tracking sensor is indispensable to improve the flexibility of automatic arc welding systems. Among the position sensing methods available, a laser displacement sensor is one of the most prevailing methods. In this study, a laser displacement sensor was examined on detecting the weld seam of lap joints in sheet metal arc welding. The output signal of the laser displacement sensor may ontain severe fluctuation from the effect of arc light, spatters, fume, etc. So a variety of signal processing methods was applied to smooth the output signal of the sensor. And then the weld joint was determined by using the central difference method. It was revealed that the quadratic mean method plays an important role in detecting the weld seam during welding especially.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.135-138
• /
• 2009

Quality evaluation of laser welded MCFC separator panels with large active area was performed. Lap joint was applied to produce stable air-tight seam weld by employing Nd:YAG laser. Results showed that surface contamination played a key role to form weld defects at the joint interface. However, there was no evidence that weld width at the lap joint changed after the stack operation time of 2,890h. Test results also revealed that the reinforcement values which were measured on the weld line after long time operation, were stable.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.180-182
• /
• 2005

Development of FSW for use in lap joint production would expend the number of applications that could benefit from the technique. In the study, an extensive investigation was carried out on FSW lap joints, including interface morphology and mechanical properties. Welding variables included welding speed, rotation speed and, of particular importance, lap joint a methods. Examination of metallographic cross sections and failure locations showed a critical sheet interface present in all welds. Results indicates FSW lap joints may potentially replace other joining processes like resistance spot welding and riveting.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2010년도 정기 학술대회
• /
• pp.624-627
• /
• 2010

최근 자동차 업계서는 차량의 온실가스 배출량을 줄이고 연비를 개선시킬 수 있는 방법 중의 하나로 경량화 소재를 사용하여 차체의 중량을 줄이는 연구가 활발히 진행 중에 있다. 특히 알루미늄 합금의 경우 기존 강재에 비해 비중이 낮아 가볍고 부식에 대한 저항성이 높아 많이 사용되어지고 있는 추세이다. 본 연구에서는 먼저, 저입열 용접공정을 적용하여 용접 변수와 토치의 각도에 따른 인장강도 특성을 비교하여 적정 용접 범위를 산정하였으며, 인장강도와 비드형상의 관계를 다중 회귀 분석을 이용하여 비드 예측 회귀 모델을 제시하였다. 또한 호감도 함수를 적용한 반응표면분석법을 이용하여 자동차 생산 현장에서 겹치기 용접 이음부의 강건한 용접 품질을 가질 수 있는 최적용접 공정 조건을 도출할 수 있는 효과적인 방법을 제안하고자 한다.

• Journal of Welding and Joining
• /
• 제12권1호
• /
• pp.102-115
• /
• 1994

This paper is to evaluate the fatigue strength of lap joints of materials applied to LNG carrier cargo containment of GAZ-TRANSPORT(GT) type, which was welded by manual and automatic TIG welding process. The thicknesses of lapped members were 1.5mm/1.5mm or 1.5mm/0.7mm in Invar to Invar joint, and 1.5mm/8.0mm in Invar to stainless steel joint, respectively. These lap joints were mainly applied to the membrance fabrication of GT-LNG carrier. Fatigue tests of Invar/Inar lap joints were conducted under the stress ratio R=0 at room temperature. The effect of mean stress and cumulative fatigue damage on the allowable stress of Invar lap joint was evaluated on the basis of test results. Fatigue test was also conducted on Inver/Stainless steel lap joints welded by automatic TIG process without filler metals. The fatigue test of the joint was carried out under the same conditions as those of Invar/invar lap joints. The fatigue strength of the joint welded without filler metal was comparable to those welded with filler metal quoted from reference. The fatigue strength of Invar/stainless steel lap joint was only dependent on the lap throat thickness, and not on the welding process. Based on test results, the applicability of TIG welding process without filler metal in Invar/stainless steel lap joint was reviewed by controlling welding variables to assure the valid throat thickness of lap joints.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.238-243
• /
• 2007

This paper is designed to estimate the adhesion strength of coating layer on galvannealed steel sheet using lap shear test. The single lap shear test is the most commonly used standard test for determining the strength of medium-strength and high strength bonds. The bond strength of bonded single lap joints on subjecting the substrates to loads is determined by lap shear forces in the direction of the bonded joint. In this study, specimen for adhesion strength test was made to attach coated sheet to cold rolled sheet and were heated in temperature of 180 for 20minutes. After test, detached parts of coatings on coated sheet were observed using SEM and EDX to identify substrate and complete detachment. The tested results showed that adhesive strength of coating is unrelated to anisotropy of sheet and is difficult to be extracted using conventional theory because of fine cracks of coating layers which were created during annealing process.