• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.6
• /
• pp.19-26
• /
• 2021

The lattice structure is attracting attention from industry because of its excellent strength and stiffness, ultra-lightweight, and energy absorption capability. Despite these advantages, widespread commercialization is limited by the difficult manufacturing processes for complex shapes. Additive manufacturing is attracting attention as an optimal technology for manufacturing lattice structures as a technology capable of fabricating complex geometric shapes. In this study, a unit cell was formed using a three-dimensional coordinate method. The relative density relational equation according to the boundary box size and strut radius of the unit cell was derived. Simple cubic (SC), body-centered cubic (BCC), and face-centered cubic (FCC) with a controlled relative density were designed using modeling software. The accuracy of the equations for calculating the relative density proposed in this study secured 98.3%, 98.6%, and 96.2% reliability in SC, BCC, and FCC, respectively. A simulation of the lattice structure revealed an increase in compressive yield load with increasing relative density under the same cell arrangement condition. The compressive yield load decreased in the order of SC, BCC, and FCC under the same arrangement conditions. Finally, structural optimization for the compressive load of a 20 mm × 20 mm × 20 mm structure was possible by configuring the SC unit cells in a 3 × 3 × 3 array.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.721-725
• /
• 2007

A fiber optic based weight sensor has fabricated using a fiber Bragg grating with a weight sensitive. The sensing concept exploits the inherent characteristics of the FBG and is based on the strain effect induced in the fiber Bragg grating through. A direct indication of the weight level is given by the shift of the Bragg wavelength caused by the expansion of the sensing material. A FBG behaves like a spectral filter which has inherent characteristics that render it very sensitive to strain and temperature. The sensing principle is also based on the strain effect induced in the FBG through the caused by the weight. The experimental setup used for the initial investigation to characterize the mass response of the sensor. The transmitted signal from the sensor was monitored using an optical spectrum analyzer with a resolution bandwidth of 0.4nm. In this paper, we presented the spectral characterization and shaping of FBG by scanning a mass element that affects a small grating fraction at a time, without permanent effects on the optical fiber when the various wavelength and strain is removed. That is, destruction when the optical fiber for weight is physically damaged.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.115-119
• /
• 2008

In this paper, the linearity of Doherty power amplifier has been improved by applying a new Photonic Bandgap(PBG) structure on the output of amplifier. The reposed spiral PBG structure is a two-dimensional(2-D) periodic lattice patterned on a dielectric slab that does not require nonplanar fabrication process. This structure has more broad stopband and high suppression performance than the conventional three cell PBG. Also, It has a sharp skirt property. We obtained the 3rd-order intermodulation distortion(IMD3) of -33dBc for CDMA applications with that of maintaining the constant power added efficiency(PAE), the IMD3 performance is improved as much as -8 dB compared with a Doherty power amplifier without PBG structure. Moreover, the physical length of PBG is shortened, therefore the whole amplifier circuit size is considerably reduced.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6B
• /
• pp.643-651
• /
• 2008

In the present paper, turbulent open-channel flows over longitudinal bedforms are numerically simulated. The Reynolds- averaged Navier-Stokes equations in curvilinear coordinates are solved with the non-linear $k-{\varepsilon}$ model by Speziale( 1987). First, the developed model is applied to rectangular open channel flows for purposes of model validation and parameter sensitivity studies. It is found that the parameters $C_D$ and $C_E$ are important to the intensity of secondary currents and the level of turbulent anisotropy, respectively. It is found that the non-linear $k-{\varepsilon}$ model can hardly reproduce the turbulence anisotropy near the free surface. However, the overall pattern of the secondary currents by the present model is seen to coincide with measured data. Then, numerical simulations of turbulent flows over longitudinal bedforms are performed, and the simulated results are compared with the experimental data in the literature. The simulated secondary currents clearly show upflows and downflows over the ridges and troughs, respectively. The numerical results of secondary currents, streamwise mean velocity, and turbulence structures compare favorably with the measured data. However, it is observed that the secondary currents towards the troughs were significantly weak compared with the measured data.

• Geophysics and Geophysical Exploration
• /
• v.3 no.2
• /
• pp.39-47
• /
• 2000

A great deal of computing time and a large computer memory are needed to solve wave equation in a large complex subsurface layers using the finite difference method. The computing time and memory can be reduced by decreasing the number of grid points per minimum wave length. However, the decrease of grids may cause numerical dispersion and poor accuracy. In this study we performed the grid dispersion analysis for several rotated finite difference operators, which was commonly used to reduce grids per wavelength with accuracy in order to determine the solution for the acoustic wave equation in frequency domain. The rotated finite difference operators were to be extended to 81, 121 and 169 difference stars and studied whether the minimum grids could be reduced to 2 or not. To obtain accuracy (numerical errors less than $1\%$) the following was required: more than 13 grids for conventional 5 point difference stars, 9 grids for 9 difference stars, 3 grids for 25 difference stars, and 2.7 grids for 49 difference stars. After grid dispersion analysis for the new rotated finite difference operators, more than 2.5 grids for 81 difference stars, 2.3 grids for 121 difference stars and 2.1 grids for 169 difference stars were needed. However, in the 169 difference stars, there was no solution because of oscillation of the dispersion curves in the group velocity curves. This indicated that the grids couldn't be reduced to 2 in the frequency acoustic wave equation. According to grid dispersion analysis for the determination of grid points, the more rotated finite difference operators, the fewer grid points. However, the more rotated finite difference operators that are used, the more complex the difference equation terms.

• Journal of Korean Society of Transportation
• /
• v.26 no.5
• /
• pp.227-235
• /
• 2008

This study analyzed the efficiency of a trunk with branches and a trunk with feeders route system comparing the user cost and operator cost of those route systems. Basically, a trunk with branches is more efficient than a trunk with feeders in the passengers' perspective if the transit system of a trunk and feeders are the same. In the case that the trunk system is hierarchically higher than the feeder system, a trunk with feeders has the competitive edge over a trunk with branches if the saving of travel cost induced by using the trunk line is larger than the increasing waiting and transfer cost. This result is consistent with the previous research by Park et al.(2007c), which analyzed the efficiency of hierarchical structure in a grid transit network. If the travel demand of each origins and destinations is low, increasing headway according to the travel demand can increase passenger load or operating efficiency in a trunk with feeders route system. In this case, a trunk with feeders route system is more prevalent as the operating cost, route length, and number of destinations increases, while it is less prevalent as the transfer cost and passengers' time value of the waiting time increases. In cases that central business district, which is located in the middle of a trunk line, generates travel demand, a trunk with feeders is more efficient than a trunk with branches with the increasing travel demand from and to the CBD. Therefore it can be concluded that to have a dual operating system between CBD and suburban is more efficient than one type transit system. The efficiency of that system can be increased through an efficient transfer system that can reduce the transfer cost.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.93-93
• /
• 2022

최근 이상기후로 인하여 우리나라 산림에 태풍 및 국지성 호우가 빈번히 발생하고 있다. 이로 인해 사면재해가 많이 발생하고 있으며 그 중 호우로 인한 많은 양의 물과 함께 토석 및 부유물이 중력에 의해 경사면을 따라 흐름 형태를 보이는 토석류 재해는 속도가 매우 빠르고 파괴적이며 그 결과는 비참하기까지 하다. 더구나 인구밀도가 낮은 산지 계곡부 뿐만 아니라 도시지역에서도 토석류 재해가 빈번히 발생하며 국내 및 해외에서도 토석류에 의한 피해사례는 자주 볼 수 있다. 이러한 토석류 재해의 피해를 줄이고자 토석류의 유동성을 저감시키기 위한 대책구조물의 시공이 많이 이루어지고 있으며 최근에는 투과형 구조물 중 하나인 원통형 기둥구조물을 그룹 형태로의 시공하는 경우가 늘어나고 있다. 토석류와 대책구조물 간의 상호작용은 월류(overflow), 쳐오름(run-up), 역류(backwater) 등의 복잡한 흐름 거동을 보인다. 하지만 원통형 대책구조물에 대한연구가 많이 이루어져 있지 않고 대규모 실험 또한 비용이 많이 소요되고 실행하기도 어렵다. 이 연구는 오픈소스 소프트웨어인 OpenFOAM을 사용하여 원통형 대책구조물의 설치 조건에 따라 토석류 흐름에 미치는 영향을 분석하였다. 짧은 시간 내에 흐름이 발생하고 비뉴튼 유체 특성을 갖는 토석류의 유효전단응력이 난류전단응력에 비해 상당히 크므로 난류의 영향은 무시하였다. 계산된 수치모의의 결과를 같은 규모로 시행한 실험결과와 비교분석 및 검증하였다. 공학학적 문제에 적용 가능하도록 비교적 낮은 해상도의 계산 격자를 사용했지만 실험에서 보여지는 토석류의 흐름거동을 양호하게 재현했으며 원통형 대책구조물의 배치조건에 따라 토석류 선단부 유속의 감소 정도 및 시간에 따른 흐름깊이 변화를 분석할 수 있었다. 이 연구는 다양한 조건을 가지는 토석류 흐름을 해석하는데 유용하게 활용할 수 있으며, 추후 복잡한 실제지형 조건을 고려하는 연구를 통하여 적용성을 확보하고자 한다.

• Journal of Korean Association for Spatial Structures
• /
• v.10 no.1
• /
• pp.67-74
• /
• 2010

This paper focuses on steel arrays regarding the application of PV system for solar power system, a renewable energy in steel structure stadium that will be built in Korea, by foreign case study. 20 cases of Steel Structure Stadiums applying PV system after 1990 were selected as the main subjects. The 20 cases of Steel Structure Stadiums were categorized by rail systems that were installed to fix PV module. As the result, linear clamping and roof-integrated type among cross rails were 28% of the whole, followed by 17% of rail-fixed type and 11% of module group-fixed type among vertical-fixed types. In addition, linear clamping and roof-integrated type among cross rails were applied in the inside of the stadium while the outside and other parts of stadiums used angle bracket to fix PV module.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.10
• /
• pp.205-213
• /
• 2019

Network robustness is one of the most important characteristics needed as the network. Over the military tactical communication network, robustness is a key function for maintaining attack phase constantly. Tactical Information Communication Network, called TICN, has mixed characteristics of lattice- and tree-type network topology, which looks somewhat weak in the viewpoint of network robustness. In this paper, we search articulation points and bridges in a current Tactical Information Communication Network using graph theory. To improve the weak points empirically searched, we try to add links to create the concrete network and then observe the change of network-based verification values through diminishing nodes. With these themes, we evaluate the generated networks through SNA techniques. Experimental results show that the generated networks' robustness is improved compared with current network structure.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.149-153
• /
• 1997

We demonstrate the operating characteristics(center wavelength, bandwidth, TE/TM polarization, tuning range) of grating-assisted co-directional coupler(GACC) filter fabricated with InGaAsP compound semiconductor. A design of waveguide structure has been focused on the narrow bandwidth characteristics of the filter. Reactive ion etching technique was employed for the uniform waveguide formation. The bandwidths(FWHM) and center wavelengths of the fabricated GACC filter were measured by 1.5 nm and 1530.6 nm for TE polarization and 1.3 nm and 1494.0 nm for TM polarization. This is the one of the narrowest bandwidth at 1530 nm region ever reported. The center wavelength shifted form 1530 nm to 1538 nm when the current of 100 mA was injected at 4.5 mm-long device. Good agreement between the designed and measured operating characteristics for some waveguide structures is demonstrated.