• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.74-82
• /
• 1998

The grain boundary etching method as a technique for assessing degradation of structural materials used at elevated temperature has received much attention since it is simple, inexpensive and easy to apply to real plant components. In this study, the technique is applied to some aged petroleum and chemical plant components such as reactors and drums. As a degradation parameter, intersection number ratio ($N_i/N_o$), is employed. The intersection number ratio ($N_i/N_o$) is defined as the ratio of intersection number ($N_i$) obtained from 5-minute picric acid etched surface to the number ($N_o$) obtained from Nital etched surface. In order to study degradation level, several relationships were measured such as the correlation between shift in ductile brittle transition temperature, $({\Delta}DBTT)_{sp}$ and intersection number ratio, ($N_i/N_o$) and the correlation between the measured ($N_i/N_o$) values and Larson-Miller Parameter values.

• Composites Research
• /
• v.31 no.5
• /
• pp.251-259
• /
• 2018

In this paper, statistical volume element modeling method was developed for multi-scale progressive failure analysis of fiber reinforced composite materials. Big-size statistical volume elements (BSVEs) was considered to minimize the size effect in the micro-scale, by including as many fibers as possible. For that purpose, a mesh cutting method is suggested and adapted into the fiber model generator that creates finite element domain rapidly. The fiber defect model was also developed based on the experimental distribution of the fiber strength. The size effects from the local load sharing (LLS) are evaluated by increasing the fiber inclusion in the micro-scale model. Finally, continuum damage mechanics (CDM) model to the fiber direction was extracted from numerical analysis on BSVEs. And it was compared with strength prediction from typical representative volume element (RVE) model.

• 한국전산유체공학회:학술대회논문집
• /
• 1995.10a
• /
• pp.197-202
• /
• 1995

비정상(unsteady) 압축성(compressible) 유동에 의한 공력음향(aeroacoustics)을 모사하여 공력소음원을 해석하기 위해서는 고차(high order)의 정확도와 높은 해상도(resolution)를 가지며, 상대적으로 계산시간을 많이 필요로 하지 않는 외재적(explicit) 유한차분법이 필수적으로 요구된다. 이것은 주어진 차분방식과 격자계로써 공간과 시간상에 존재하는 미소크기의 파동성분들을 충분히 구현하여야 만족할 만한 수치해를 얻을 수 있기 때문이다. 본 연구에서는, 그러한 유한차분법 중 최근에 관심의 대상이 되고있는 삼각(tridiagonal)또는 오각(pentadiagonal) 집적유한차분법(compact finite difference scheme)이 최대의 해상도를 갖도록 하는 수학적인 방법을 개발하고, 이 방법으로써 새롭게 집적유한차분법을 최적화하였다. 개발된 최적화 방법은, 푸리에 해석법(Fourier analysis)을 통하여 파동수(wavenumber) 영역에서 수학적으로 계산된 위상오차(phase error)를 최소화하는 것이며, 이러한 개념과 방법은 본 연구에서 처음으로 집적유한차분법에 적용되었다. 여러가지 절단정확도(truncation order)에 대해서 최적화 된 집적유한차분법들이 실제 공간과 시간상에서 보여주는 정확도와 오차특성을 알아보기 위하여, 이 방법들을 1차원 선형파동방정식에 적용하였고, 이 결과를 통하여 가장 정확하고 효과적인 절단정확도의 집적유한차분법을 선별하였다. 특히, 오각(pentadiagonal)법에 비해 더욱 효율적인 6차 삼각(tridiagonal)법을 1차원 Euler방정식에 적용하여, 비선형 파동에 대한 모사를 수행할 수 있었다.

• Journal of Navigation and Port Research
• /
• v.37 no.1
• /
• pp.1-7
• /
• 2013

In this paper the developed prediction technique of wave-making resistance performance for a ship attached with a vertical blade had been verified. Numerical analysis program as a prediction technique had been developed using the Rankine source panel method and the vortex lattice method(VLM). The nonlinearity of the free surface conditions was fully taken into account using the iterative method and the trim and the sinkage of the ship were also considered in the numerical analysis program. Panel cutting method was applied to get hull surface panels. Numerical computations were carried out for a 4000TEU container carrier and the vertical blade was attached 6 different locations astern. To investigate the validity of the numerical analysis program the commercial viscous flow field analysis program FLUENT was used to obtain the viscous flow field around the ship and the model test was performed. The model test results were compared with the numerical analysis results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.4
• /
• pp.245-255
• /
• 2019

This paper describes on aerodynamic analysis based on the truncation rate of guided-weapon nose using computational fluid dynamics. The shape to perform the analysis is only the body of the guided weapon and the diameter to length ratio is 10.7. Three nose shapes were selected and hemisphere, 25% and 50% truncation were compared. For the accurate CFD analysis of the body, the grid method and the analytical method were selected and verified using NASA wind tunnel test data. For the three nose shapes, the drag analysis for the flight Mach number is 6~20% different. This difference was analyzed by the pressure distribution from nose to base.

• Korean Journal of Materials Research
• /
• v.6 no.3
• /
• pp.253-263
• /
• 1996

고온.고압하에서 장시간 사용되는 고온부재용 구조물은 경년열화현상을 나타낸다 그러므로 구조물의 안정성 측면에서 재질열화의 정도를 정량적으로 평가하는 것이 중요하다. 그러나 실기 구조물에서 채취할 시험편의 크기와 수는 제한이 되기 때문에 새로운 비파괴적인 평가법이 요구되고 있다. 따라서 본 연구에서는 화력발전설비에 이용되는 탄소강과 페라이트강에 대한 열화도의 평가를 위해 입계부식법의 적용 가능성을 조사한다. 시험결과, 재질열화의 정도는 사용시간보다 사용온도에 더 큰 영향을 받았으며, Larson-Miller인자와 열화도([$\Delta$DBTT]SP)사이의 관계는 선형적이었으나, 강종에 따라 다른 기울기를 보였다. 반면, 연성-취성천이온도 ([$\Delta$DBTT]SP)와 격자절단비(Ni/No)와 관계는 강종에 무관하게 선형적인 비례관계를 나타내었다. 또한, [$\Delta$DBTT]SP와 Ni/No 의 관계로부터 입계부식법은 페라이트계 강뿐만아니라 탄소강에 대해서도 유용한 재질열화 평가 방법임을 알 수 있었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.100-100
• /
• 2022

일반적으로 유체와 구조물간 상호작용의 수리동역학적 모의에서는 벽경계조건을 통하여 유동에 대한 구조물의 영향이 반영된다. 하지만 도심지에서 발생한 홍수를 예측하려는 경우 이러한 방법으로는 밀집한 구조물들 사이에 형성된 좁은 길들로 인하여 세밀한 격자망을 요하여 큰 계산량을 유발하고 빠른 예측 속도를 기대할 수 없게 한다. 최근 이러한 문제를 극복하기 위해 성긴 격자망에서도 구조물의 유체에 대한 영향을 반영할 수 있도록 하는 방법들이 큰 관심을 받고 있다. 그 중에서도 다공성 천수방정식은 벽경계조건 대신 다공도(posority)의 개념을 이용한 모형으로 도시범람모의에 있어 계산량과 정확도를 가장 적절하게 타협한 모형으로 보고되고 있다. 이러한 흐름에 맞추어 본 연구는 다공도 천수방정식을 해석하는 수치 기법을 개발하였고, 여기에 최근 쌍곡선계 방정식의 수치적 연구들에서 소개된 주요 특징들이 반영되도록 설계하였다. 우선, WENO 기법과 Runge-Kutaa 기법을 통하여 공간과 시간에 대한 고차 정확도를 만족시켰다. 이 때, 재구성 변수와 알고리즘를 새롭게 제시하여 정상흐름조건에 대한 플럭스항과 생성·소멸항간 절단오차에 의한 비물리적인 흐름생성을 억제하였다. 또한, 수치모의 중 음수심의 발생으로 인하여 수치모형이 불안정해지는 현상을 막기 위해, 양-보존성 제한자를 구축하였다. 마지막으로 도심지에서 즐비한 인위적인 구조물에 의해 나타나는 지형적인 불연속의 효과를 적절하게 반영할수 있도록 정상파 재구축의 단계를 구축하여 수치 기법에 반영하였다. 이렇게 구성된 수치기법은 리만문제의 해석해에 기반하여 기존의 주요 연구들의 결과와 비교되었고, 그 결과 본 연구의 방법이 정확성, 수렴성, 안전성의 측면에서 가장 우수함을 수치적으로 증명하였다.

• The Journal of the Petrological Society of Korea
• /
• v.9 no.4
• /
• pp.205-210
• /
• 2000

Measurements of phase identification and degree of orientation for fine-grained (about 0.3 mm in diameter) minerals in rock samples performed by micro-area X-ray diffractometer.$Al_{2}SiO_{5}$ polymorphs (andalusite, kyanite and sillimanite) were chosen for the measurements and target minerals were existed on thin sections. Micro-area X-ray diffractometer is composed of 3(${\omega}\;{\chi}\;{\phi}$)-circle oscillating goniometer and position sensitive proportional counter (PSPC). $CuK_{\alpha}$ radiation was used as X-ray source and a pin hole ($50\;\mu\textrm{m}$$ in diameter) collimator was selected to focus radiation X-ray onto the target minerals. Phase identification and diffracted X-ray peak indexing were carried out by 3(${\omega}\;{\chi}\;{\phi}$)-circle oscillation measurement. Then, 2(${\omega}\;{\phi}$)-circle oscillation measurement was made for the purpose of searching the prevailing lattice plane of the minerals on thin section surface. Finally, for a selected peak by 2-circle oscillation measurement, X-ray pole figure measurement was executed for the purpose of check the degree of orientation of the single lattice direction and examine its pole distribution. As a result of 3-circle oscillation measurement, it was possible that phase identification among $Al_{2}SiO_{5}$ polymorphs. And from the results of 2-circle oscillation measurement and X-ray pole figure measurement, we recognized that poles of andalusite (122), kyanite (200) and sillimanite (310) lattice plances were well developed with direction normal to each mineral surface plane respectively. Therfore, the measurements used with micro-area X-ray diffractometer in this study will be a useful tool of phase identification and degree of orientation measurement for fine-grained rock forming minerals.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.1
• /
• pp.22-31
• /
• 1997

The grain boundary etching method as a method for assessing degradation of structural materials has received much attention because it is simple, inexpensive and easy to apply to real components. In this study, the effectiveness of the method is verified by successfully applying the technique to in-service components of aged fossil power plants such as main steam pipes, boiler headers an turbine rotors. A new degradation parameter, intersecting number ratio (N$_{1}$/N$_{0}$), is employed. The intersecting number ratio (N$_{1}$/N$_{0}$) is defined as the ratio of intersection number (N$_{1}$) obtained from 5-minute picric acid etched surface to the number (N$_{0}$) obtained from nital etched surface. Two kinds of test materials, 2.25Cr-1Mo steel and 1Cr-1Mo-0.25V steel, were artificially thermal-aged at 630.deg. C in different levels of degradation., (N$_{1}$/N$_{0}$) were measured. And, correlations between the measured values and LMP values calculated from aging temperature and aging time were sought. To check the validity of the correlations obtained in laboratory, similar data were measured from service components in four old Korean fossil power plants. These on-site measurement data were in good correlation with those obtained in the laboratory.oratory.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.7
• /
• pp.1064-1072
• /
• 2001

It is very important to evaluate material degradation like temper and carbide embrittlements to secure the reliable and efficient operational conditions and to prevent brittle failure in service. The extent of material deterioration can be accurately evaluated by mechanical test such as impact test or creep test. But it is almost impossible to sample a large specimen from in-service plants. Thus, the material degradation evaluation by a non-destructive method is earnestly required. Recently the non-destructive test technique which uses the grain boundary etching characteristics owing to the variation of material structures has been proposed. However the program for material degradation evaluation using the grain boundary etching method(GEM) in Windows 98 domain doesnt be developed now. The aims of this paper are to develop the program and to complete the new master curve equations for the evaluation of material degradation on in-serviced high temperature components.