• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.36-41
• /
• 2005

The aerodynamic characteristics of the oscillating airfoil(NACA0012) were measured by experimental methods by using the airfoil oscillating test rig installed at KARI 1m wind tunnel. The chord of the airfoil is 0.2m and the span is 0.75m. The lift and pitching moments were calculated by integrating the surface pressure measured by strain-gage type pressure sensors. The test condition is like this : the reduced oscillating frequency(k) < 0.1, Re ~ 820,000, Mach < 0.25. The test results were compared with the reference data published by other facilities.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.173-175
• /
• 2007

부산신항 남컨 배후지준설토 투기장은 국제도시 부산의 관문이 될 부산신항만 입구부에 위치한 관계로 아름답고 튼튼한 호안이 될 수 있도록 하고, 입찰안내서에 제시된 호안법선변경 금지, 호안마루높이 DL.(+)7.50m 유지 조건을 준수하면서 최적의 구조물이 되도록 하였다. 본사업지는 지형적 특성상 복잡한 형태의 고파랑 작용으로 수리학적으로 월파, 반사파, 연파를 제어하는 경사호안 구조물을 도입하였고, 초연약지반이 대심도로 분포하는 특성을 고려하여 개선된 S.C.P 연약지반 처리공법을 적용하여 기초굴착 없는 친환경적이고 배수기능을 향상시킨 융기토 유용형 S.C.P공법을 적용하였다. 호안전구간은 친수개념을 도입하였으며, 호남도 주변 해양생태계 보호를 위하여 미티게이션(mitigation) 개념을 도입하여 환경복원 계획 및 생태형 친수호안을 구상하였다.

• Journal of Welding and Joining
• /
• v.15 no.2
• /
• pp.81-88
• /
• 1997

The residual stresses produced by a circumferential weld between axisymmetric cylinders are one of the most important problems concerning buckling strength, fatigue strength, stress corrosion cracking in shell structures, and arc quite different from those due to a butt weld between flat plates. This paper presents experimental studies on weld cylinder models of various heat inputs and thin cylinder diameters by blind hole drilling method. As a result, it is certified that weld residual stress (axial stress and hoop stress) is larger, as heat input and shell cylinder diameter are larger, and that experimental results show good agreement with the result of preceding researchers.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.93-100
• /
• 2020

The turbopump of the liquid rocket engine adapts an inducer to minimize the cavitation due to the variations of the propellants supply condition. However, the inducer introduces cavitation instabilities which are well-known problems in the engine development. In this paper, operational characteristics by the cavitation instabilities are analyzed and the reliability of the engine is checked when the first stage engine of the KSLV-II is tested at the low inlet pressure conditions. The characteristic frequencies representing the cavitation instabilities of the LOx pump are clearly found in various high frequency sensor signals around the entire engine in addition to the LOx and fuel pump.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.987-992
• /
• 2009

Continuous Compaction Control is a new cutting edge technique in United States, Japan and European construction market that uses an instrumented compactor to measure soil stiffness in real time usually with vehicle tracking system such as Global Navigation Satellite System (GNSS). In this study, soil stiffness was evaluated by adapting Fourier transforming technique with acceleration data obtained from accelerometers used as a continuous compaction control instrument. The soil stiffness obtained by accelerometers gave analogous results with reference results such as dry density, elastic modulus obtained from Geogauge and Light falling deflectometer.

• Explosives and Blasting
• /
• v.36 no.2
• /
• pp.1-9
• /
• 2018

In this paper, AUTODYN blasting simulation of single blast hole were conducted to evaluate the blasting effects of Polymer Gel. The coupling mediums used as the filling material around an explosive charge were air and gelatin. each simulation case was D I(decoupling index) 1.0, 1.25, 1.56 with air or polymer gel coupling materials. In order to evaluate blast effects full charge model was used as a reference for evaluation of blasting effects. The results of numerical analysis showed that fragmentation of a limestone model of were much more fractured by polymer gel medium than by air medium. As expected, the transmitted peak pressure was higher polymer gel coupled model than in air medium.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.3
• /
• pp.197-213
• /
• 2012

Disc cutter is a key cutting tool for rock excavation by TBMs. This study aimed to characterize the deformation of a cutter ring by strain measurement as well as infrared thermal camera measurement during a series of linear cutting tests for a hard rock. The strain measurement results indicated that the cutter ring clearly showed a linear elastic behavior. The data obtained from the infrared thermal camera measurement demonstrated that the maximum temperature increase in the cutter ring was below $14.4^{\circ}C$. The deformation and temperature increase of the cutter ring during rock cutting were insignificant in a given cutting test condition of this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2559-2565
• /
• 2013

Material of boat hull has been used mainly with FRP composite materials until now. FRP boat hull manufacturing began to be restricted after the 2000's under international regulation on ocean environment safety. Shipyard on a small scale has manufactured polyethylene canoe and kayak hulls. Polyethylene has the melting point lower than the existing hull materials. Thermal stress occurs on outer hull surface when the polyethylene boat hull is exposed to sunlight. If it happens everyday, boat hull undergoes fatigue damage due to thermal fatigue. Therefore, this study presents the statistical fatigue life estimation on the HDPE boat hull subject to repeated thermal stress under three point bending condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.34-40
• /
• 1998

The burr produced on piece part edges in machining operations must be removed for most parts to function effectively. Although considerable cost have been expended in improving deburring methods, little energy has been applied toward minimizing burrs. This study has been carried out to prevent the burrs produced on pure aluminium under various working condition and specimen shape in turning operations. The computer image processing system was used for measurement of size of burr, such as burr length, burr depth and burr area. The size of burr showed a decreasing tendency with the increase of rake angle and side cutting angle but it increased rapidly with the increase of depth of cut and the cutting speed has no effect on size of burrs. The size of burr rapidly decreased with the increase of edge angle and burrs are not occurred if edge angle is over 80$^{\circ}$.

• Journal of Korea Game Society
• /
• v.19 no.1
• /
• pp.135-146
• /
• 2019

World Health Organization reveals its plan for listing 'Gaming Disorder' on the 11th International Disease Codes (ICD-11) in 2018 and it opens hot debate among scholars on its validity and timeliness. Korea, however, seems to have avoided the issue without appropriate academic refutation. In this paper, we review past academic studies related to game addiction or disorder focused on their validity of disorder measurement tools, research designs and the effect of neuroimaging studies. This analysis reveals that excessive use of gaming is not sufficient to register it as a disease and there is a risk of stigmatizing healthy gamers.