• Journal of Sensor Science and Technology
• /
• v.9 no.6
• /
• pp.404-415
• /
• 2000

This paper describes several performances and nondestructive inspection for deterioration due to forest fires in overhead transmission lines. After discussing corrosion mechanism such as atmospheric and galvanic corrosion for aged ACSR conductors and its detection for them are presented. Through impedance analysis of a solenoid coil, it is shown that the eddy current sensor may be available to inspect severe fault or local corrosion. As the solenoid coil changes its impedance when the test conductor is inserted into the coil, it can be possible to measure deterioration degree caused by forest fires. Tensile strength, extension rate and sensor impedance are tested for some samples degraded by artificial fire. As increasing blazed period to some extent, the strength of aluminum strand begins to be reduced remarkably, while galvanized steel strand holds the similar strength to the initial value, despite of appearing a little loss of zinc layer. In general, it is shown that the sensor impedance would be increased while the tension load of conductor is reduced and the extension rate is contrarily increased. Therefore, the sensor output could exhibit the changes of mechanical performances, and would be used to detect such deterioration caused by forest fire in ACSR conductors built on the ridge of mountains. Finally, it was verified that the solenoid coil could be applicable to obtain any crucial inform for serious deterioration due to forest fires.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.4
• /
• pp.398-405
• /
• 2001

The rivet joint has typical structural feature that can be initiation site for the fatigue crack due to the combination of local stress concentration around rivet hole and the moisture trapping. From a viewpoint of structural assurance, it is crucial to evaluate the size of crack around the rivet holes by appropriate nondestructive evaluation techniques. Lamb wave that is one of guided waves, offers a more efficient tool for nondestructive inspection of plates. The neural network that is considered to be the most suitable for pattern recognition has been used by researchers in NDE field to classify different types of flaws and flaw sizes. In this study, clack size evaluation around the rivet hole using the neural network based on the back-propagation algorithm has been tarried out by extracting some features from the ultrasonic Lamb wave for A12024-T3 skin panel of aircraft. Special attention was paid to reduce the coupling effect between the transducer and the specimen by extracting some features related to time md frequency component data in ultrasonic waveform. It was demonstrated clearly that features extracted from the time and frequency domain data of Lamb wave signal were very useful to determine crack size initiated from rivet hole through neural network.

• Korean Journal of Clinical Laboratory Science
• /
• v.51 no.3
• /
• pp.301-308
• /
• 2019

The emergence and spread of multidrug resistant (MDR) Pseudomonas aeruginosa is a critical problem worldwide. The pathogenesis of P. aeruginosa is due partly to the production of several cell-associated and extracellular virulence factors. This study examined the distribution of virulence factors and antimicrobial resistance patterns of carbapenem-resistant P. aeruginosa (CRPA) isolated from a tertiary hospital in Daejeon, Korea. Antimicrobial susceptibility testing was performed using the disk diffusion method, and PCR and DNA sequencing were performed to determine for the presence of virulence genes. In addition, the sequence type (ST) of MDR P. aeruginosa was investigated by multilocus sequence typing (MLST). Among 32 CRPA isolates, 14 (43.8%) were MDR and the major ST was ST235 (10 isolates, 71.4%). All isolates were positive for the presence of virulence genes and the most prevalent virulence genes were toxA, plcN, and phzM (100%). All isolates carried at least eight or more different virulence genes and nine (28.1%) isolates had 15 virulence genes. The presence of the exoU gene was detected in 71.4% of the MDR P. aeruginosa isolates. These results indicate that the presence of the exoU gene can be a predictive marker for the persistence of MDR P. aeruginosa isolates.

• Korean Journal of Clinical Laboratory Science
• /
• v.52 no.4
• /
• pp.342-348
• /
• 2020

Uropathogenic Escherichia coli (UPEC) is a major cause of urinary tract infections (UTIs), which is one of the most common infectious diseases in humans worldwide. Since UPEC is increasingly gaining resistance to many antimicrobial agents, antibiotic therapy of UTI has recently become a great concern. This study examined the epidemiological relationship, and antimicrobial resistance patterns of 84 UPEC isolates obtained from UTI patients in Daejeon, from March to December 2017. Molecular epidemiology was investigated by multilocus sequence typing (MLST), and an antimicrobial susceptibility test was determined using an E-test. In this study, UTI was more common in females (73.8%) than in males (26.2%), and the highest incidence of UTI was observed in the age group in their 70s. Among the 84 UPEC isolates, 59 isolates (70.2%) were multidrug-resistant (MDR), and the major sequence type was ST131 (44 isolates, 52.4%). Interestingly, the rates of MDR in non-ST131 isolates (72.5%) were higher compared to ST131 isolates (68.2%). These results indicate the possibility of the development and spread of MDR in non-ST131 isolates. Effective surveillance networks and continuous research need to be conducted globally to prevent the emergence and international spread of MDR non-ST131 isolates.

• Journal of radiological science and technology
• /
• v.36 no.1
• /
• pp.1-10
• /
• 2013

IEC publications have applied in many countries all over the world such as Europe or Japan and these also have been published as in dustrial standards (KS) and notifications of Korea Food and Drug Administration (KFDA) in Korea. As the general standard of IEC 60601 series for medical electric (ME) equipment was revised as $3^{rd}$ edition in 2005, additional and particular standards have been revised or established newly. Under these circumstances, it is importance for manufacturing and assembling companies or authorized testing companies to understand the trend for revisions of IEC publications. Therefore in this study, the latest version of 3 IEC standards related to medical X-ray equipment : IEC 60601-2-44 for X-ray equipment for computed tomography (CT), IEC 60601-2-45 for mammographic X-ray equipment and IEC 60601-2-54 for X-ray equipment for radiography or radioscopy were covered and analyzed for trends and features accompanied by revision based on IEC 60601-1 $3^{rd}$ Ed. As KFDA notifications in force have referred to the particular standards based on 2nd edition of IEC 60601-1, those revised version of 3 particular standards were compared to KFDA notifications in force. The features of the latest standards applying IEC 60601-1 $3^{rd}$ Ed were shown as following: 1) Requirements for mechanical hazards, especially (motorized) moving parts were emphasized. 2) Indication and recording of patient dose were required. 3) Risk management process was introduced and enabled to monitor potential risks systematically. 4) DR system (digital radiography system) as well as analogue system (film-screen system) was included in the scope. Presently, KFDA will revise the notifications applying the particular standards based on IEC 60601-1 $3^{rd}$ Ed in a few years. Therefore the features of particular standards applying IEC 60601-1 $3^{rd}$ Ed was expected to help manufacturers, assemblers or testing companies of medical electric equipment understand IEC publications or KFDA notifications slated to be published.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.151-152
• /
• 2003

최근 NMR, MRI, x-선 등 전자파의 기술이 발전되면서 이들을 이용하여 내부품질을 검출하는 보다진보된 연구가 수행되고 있다. 관련 연구로는 자기공명영상을 이용하여 내공수삼 및 정상수삼의 내부를 촬영하여 T$_1$, T$_2$의 값을 측정하여 내부조직의 이상유무를 추정하였고, 또한 MRI에 의해 수삼의 내부품질 뿐만 아니라 연근 판정 가능성을 검토하는 등 많은 연구가 수행되고있다. 이 연구에서는 MRI 시스템을 이용하여 수삼의 내부단면 영상을 획득하여 내부결함 유무를 검출하고, 또한 동일한 수삼을 대상으로 홍삼 제조 후 내부품질의 변화 특성을 조사하고자 수행하였다. 공시재료는 충북 음성에 있는 인삼연초연구원에서 4~6년 근 된 수삼을 이용하였고, 시험 장비로는 국내 MRI 생산 전문 업체인 ISOL Tech. Co.에서 개발한 의료용 장비인 CHORUS 1.5T(자속밀도 1.5 Tesla)를 이용하였다. 슬라이스 두께/간격은 5mn/5mn, 촬영 단면수는 15장/시료, 영상영역(FOV)은 180mmx90mm, image size는 256$\times$128 pixels 그리고 TR/TE는 각각의 이완상수별로 500/13(Tl), 4,000/63(T2) 및 2,200/21(Pd)에 대한 단면영상을 얻었다. 5개의 수삼을 동시에 뇌두에서 뿌리 쪽으로 MR 단면영상을 획득하였다. 이완상수 T$_1$, T$_2$, Pd에 대해서 MR 영상을 획득하였으며, 총 15장의 단면 영상 중 내부 상태를 가장 잘 식별 할 수 있는 영상을 조사한 결과 T$_1$과 Pd에서 촬영한 영상에서는 내부상태가 잘 나타났으나, T$_2$에서 얻은 영상은 영상의 손실이 많이 발생되었다. 한편, T$_1$에 대해서 뇌두에서 뿌리쪽으로 가면서 각 위치에 따라 수삼 내부의 부패된 영상이 나타나 이에 대한 판정은 가능한 것으로 나타났다. 2000년도와 2001년도에 각각 수확.저장된 수삼을 부위별로 단면영상을 MRI로 측정하고, 그 시료를 인삼연초연구원(음성시험장)에서 홍삼으로 제조한 후 수삼 상태에서의 내부품질과 홍삼으로 제조된 후의 내부품질 변화를 조사하였다. 총 20본의 수삼을 MRI 시스템으로 영상을 획득하였고, 모든 시료에 대해서 내부조직의 상태를 관찰하였다. 수삼의 수분함량은 뇌두로부터 1cm부위를 절단하여 조사하였고, 수삼조직은 절단시 단면의 달관 조사에 의한 성적이며 홍삼품질은 제조삼의 조직상태를 절단하여 육안판별로 검사하였다. 총 20본의 수삼 중 정상은 16본 이었고, 이들은 홍삼으로 제조된 후 내공 내백 등이 혼재되어 나타났으며 정상수삼이 정상홍삼으로 나타난 경우는 5본이었고, 내백은 5본, 내공은 6본으로 조사되었다. 또한 수삼에서 4본은 썩은 부위가 포함되어있는 수삼이었는데 홍삼으로 제조되었을 때 3본은 내백으로 되었고 1 본은 수삼에서 썩은 부위가 1/4정도로 미미해서 홍삼 제조시 정상으로 나타났다. 일반적으로 홍삼 제조시 내공의 발생은 제조공정에서 나타나는 경우가 많으며, 내백의 경우는 홍삼으로 가공되면서 발생하는 경우가 있고, 인삼이 성장될 때 부분적인 영양상태의 불충분이나 기후 등에 따른 영향을 받을 수 있기 때문에 앞으로 이에 대한 많은 연구가 이루어져야할 것으로 판단된다.

• Korean Journal of Food Science and Technology
• /
• v.38 no.2
• /
• pp.197-201
• /
• 2006

Long-term storage technology was developed to extend shelf-life of citron (Citrus junos). Changes in quality characteristics of blanched and frozen citron peels (type A, without blanching for control; type B, blanched at $95^{\circ}C$ for 2 min; type C, blanched at $95^{\circ}C$ for 2 min, sugar added; type D, blanched at $95^{\circ}C$ for 5 min) during frozen storage were evaluated. Citron jam was prepared using frozen citron sample B, which showed the highest quality characteristics during storage, and high quality characteristics, such as yield and overall acceptability, were obtained when using 40% frozen citron, 41% sugar, 18.56% glutinous starch syrup, 0.39% pectin, and 0.05% citric acid. During storage of both blanched and frozen citron peels and citron jam made of frozen citron peel, changes in characteristics such as pH, total acids, soluble solids, and browning, were lower than those of control. Sensory evaluation for sourness, sweetness, and overall acceptability of citron jam made with frozen citron peel during storage showed higher values than those of control.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.6
• /
• pp.545-557
• /
• 2017

The study is about the efficient alternative to concrete surface in the field of visual inspection technology for deteriorated infrastructure. By combining industrial drones and deep learning based image analysis techniques with traditional visual inspection and research, we tried to reduce manpowers, time requirements and costs, and to overcome the height and dome structures. On board device mounted on drones is consisting of a high resolution camera for detecting cracks of more than 0.3 mm, a lidar sensor and a embeded image processor module. It was mounted on an industrial drones, took sample images of damage from the site specimen through automatic flight navigation. In addition, the damege parts of the site specimen was used to measure not only the width and length of cracks but white rust also, and tried up compare them with the final image analysis detected results. Using the image analysis techniques, the damages of 54ea sample images were analyzed by the segmentation - feature extraction - decision making process, and extracted the analysis parameters using supervised mode of the deep learning platform. The image analysis of newly added non-supervised 60ea image samples was performed based on the extracted parameters. The result presented in 90.5 % of the damage detection rate.

• Journal of radiological science and technology
• /
• v.34 no.4
• /
• pp.263-269
• /
• 2011

Since the spine radiography were explained differently at every several hospitals and textbooks. the technique has not been accurately defined and interfered each other. We would like to define the most appropriate positioning for clinical cases, and reference books, by comparing scoliotic angle and lordotic angle. From Mar 2009 to Sep 2011, 85 patient cases were studied, who had not been undergone surgical treatment among spondylopathy patients. Scoliotic angle and lordotic angle were measured, using Cobb's method. We analyzed statistically using t-test(SPSS 18), and evaluated spine general radiography position. Moreover, we researched on the actual condition at 10 university hospitals in Seoul. The results of scoliotic angle measurement, the value at erect position showed 20.98% higher than supine position, and it has statistical significance (p<.01). In lordotic angle measurement, the value at neutral holding position represented 29.3% higher than supine position, and it also has statistical significance(p<.01). The results of clinical survey, supine posine(70.0%) took much higher possession than erect position(30.0%). In conclusion, compare to supine position, erect position shows increased scoliotic and lordotic angle. It was agreed with the importance of clinical erect position radiography, which gravity affects. So clinical radiologist must recognize the difference, and conduct an accurate study.

• Journal of the Korean Society for Railway
• /
• v.19 no.1
• /
• pp.29-37
• /
• 2016

The type approval system of the railway safety law, which was enforced in 2014, has been preferentially applied to the field of railway vehicles. The type approval system addresses railway vehicles and railway constituents. Unlike the previous system, it requires serial verification stages divided, in consecutive order, into verification of design compatibility and conformity and type test. These stages are in accord with international certification systems including TSI certification of the European commission. This study has been carried out to find and meet the design requirements for a coupler head, which is a part of the automatic coupler system; requirements were drawn from TSI and technical specifications that are subordinate to the domestic railway approval system. Through this study, it has been found that there exist 34 design requirements to acquire a complete coupler head. Among those requirements, 32 were verified by document inspection and two were able to be verified by performing FEA and gathering range analysis data.