• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.4
• /
• pp.364-374
• /
• 2012

The purpose of this study is to perform the reliability-corrected development cost estimation of the launch vehicle at the conceptual design phase. In order to estimate the launch vehicle development cost, the estimation method based on the independent variable such as the rocket performance and dry mass has been mainly implemented up to now. This approach has made the approximate cost estimation possible, however, the cost variation according to the reliability requirement could not be reflected. In this paper, the cost estimation methodology that introduces the reliability factor in addition to the performance and mass in the TRANSCOST model is presented in order to improve the limitation of current cost estimation method. The development cost of KSLV(Korea Space Launch Vehicle)-II is estimated on the basis of this newly implemented concept with reliability as an added parameter.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.4
• /
• pp.27-37
• /
• 1998

The sloshing is very important in a safe transport of the liquid cargo by a ship. With the increasing number of supertanker and LNG carriers, this problem has become increasingly more important. In order to study the magnitude and characteristics of impact pressures due to sloshing, experiments ware performed with a rectangular tank and compared with numerical results. Structural responses of tank wall under impulsive pressures were measured. Structural vibrations induced by the sloshing load were analysed by including hydroelastic erects in terms of added mass and damping. To check the validity of the numerical model, the natural frequencies of plate in air and water were compared with measurements, and a good agreement was found. In the case that a plate vibrates under impulsive loads, the pressure on the flexible plate is larger than that on the rigid plate without hydroelastic effects, which was confirmed experimentally. The frequency of oscillatory pressure as well as accel%pion coincides with the natural frequency of plate in water.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.124-132
• /
• 2018

This research presents the results of an investigation on the characteristic of multi-component blended high fluidity mortars. The binder was blended ordinary Portland cement(OPC), ground granulated blast furnace slag(GGBFS), calcium sulfoaluminate(CSA) and ultra rapid setting cement(URSC). The GGBFS was replaced by OPC from 30%(P7 series), 50%(P5 series) and 70%(P3 series), CSA and URSC was 10% or 20% mass. The superplasticizer of polycarboxylate type were used. A constant water-to-binder ratio(w/b)=0.35 was used for all mixtures. Test were conducted for mini slump, setting time, V-funnel, compressive strength and drying shrinkage. According to the experimental results, the contents of superplasticizer, V-funnel and compressive strength increases with an increase in CSA or URSC contents for all mixtures. Moreover, the setting time and drying shrinkage ratio decrease with and increase in CSA or URSC. CSA decreased dry shrinkage but URSC had less effect. However, the mixed binders of CSA and URSC had a large effect of reducing drying shrinkage by complementary effect. This is effective for improving the initial strength of URSC, and CSA is effective for the expansion and improvement of long-term strength.

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.229-232
• /
• 2000

The carbon dioxide, nitrogen, and phosphate removals from wastewater using microalgae have extensively been studied. Especially, the green colonial algae Botryococcus braunii is characterized by unusual high hydrocarbon contents, ranging from 15 to 75% of dry weight, as long-chain unsaturated hydrocarbons. These hydrocarbons suggest that the possibility of renewable biofuels to be converted into useful fuels such as gasoline by simple catalytic cracking. The poor recovery (18 - 32%) of hydrocarbon from B. braunii culture in two-phase bubble column seems to be caused by insufficient mixing between two phases, which was operated using only aeration on the narrow interface between hydrophobic solvent and cell suspension. In addition, hydrocarbon was entrapped tightly in cell-matrix (formed by exopolysaccharide) of algal colony, which make difficult to extract using two-phase system. In order to overcome low recovery efficiency, two-stage extraction culture system including culture vessel and two-phase separator is now under development, resulted improving contact between solvent phase and cell suspension. Hydrocarbon recovery using this process was more than two times as that using two-phase extraction culture.

• 한국생물공학회:학술대회논문집
• /
• 2002.04a
• /
• pp.112-115
• /
• 2002

The green colonial algae Botryococcus braunii is characterized by unusual high hydrocarbon contents, ranging from 15 to 75% of dry weight, as long-chain unsaturated hydrocarbons. In two-phase bubble column using various organic solvents, poor recovery 08 - 32%) of hydrocarbon seems to be caused by insufficient mixing between two phases, which was operated using only aeration on the narrow interface between hydrophobic solvent and cell suspension. In addition, hydrocarbon was entrapped tightly in cell-matrix (formed by exopolysaccharide) of algal colony, which make difficult to extract using two-phase system. To improve recovery efficiency, mixed-solvent of extractive solvent (octane) and biocompatible solvent (octane) was tested in two-phase column for in situ extraction. In two-phase extraction culture using mixed-solvent, the algal growth was intensely inhibited even at low concentration of polar octanol solvent. the hydrocarbon recovery in two-stage cell-recycle extraction showed a 2.9 fold increase (57%) over that in two-phase extraction. Up to 60 % of hydrocarbon could be recovered without serious cell-damage in the case of downstream separation for 6 h at the high recycle flow rate using this process after batch culture.

• Journal of Conservation Science
• /
• v.12 no.1 s.15
• /
• pp.71-82
• /
• 2003

The paper relics excavated from the 4th excavation of the historical spot No.259 Seonwon temple area were analyzed and conserved. Because these works remained folded, the most important conservation treatment was a separation. This process depended on the state of the works: dry state works were separated using Gore-Tex chamber and the filtrated water, wet state works were separated through vacuum freeze drying method. Analyses of the paper relics performed were examination on the paper to find its distinction, binocular microscope and SEM on fiber, and XRF on character ingredient. This study presumed the times though $C^{14}$ dating of these works. The works were able to be classified through analysis and conservation treatment. This separation made lost part of the works conserve an archetype. This study presented the application of conservation methods on the paper relics which are in the bad condition and obtained information through carbon dating of it.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.1
• /
• pp.39-45
• /
• 2018

Research on FA(Fly ash) is actively carried out, while the research on BA(Bottom ash) is not so, and research on BA recycling field is urgently required. Therefore, in this study, we investigated the lightweight and thermal insulation characteristics of BA mortar by comparing BA mortar made with porous dry BA(air-cooled) and general mortar. To investigate the lightweight of BA, density test, unit volume mass test and SEM(Scanning Electron Microscope) test were performed. BA mortar and general mortar molds were prepared for the thermal insulation test at room temperature and humidity environment determined by KS A 0006 and they were dried at the temperature of $105{\pm}2^{\circ}C$ until the weight became constant. As a result of the lightweight test, the lightweight of BA mortar is about 30% lighter than the general mortar. Therefore, BA is expected to contribute to reduce the building load when used as building material. As a result of thermal insulation test, the thermal conductivity of BA mortar is about 30% better than that of general mortar.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.1
• /
• pp.48-55
• /
• 2022

This study uses the recovered water as mixing water and artificial lightweight aggregate pre-wetting water as part of a study to increase the recycling rate and reduce greenhouse gas of the ready-mixed concrete recovered during the concrete transport process, and cement fine powder of blast furnace slag(BFS) and fly ash(FA). The engineering characteristics of the three-component lightweight aggregate mortar used as a substitute were reviewed. For this purpose, the flow, dry unit mass, compressive strength, drying shrinkage, neutralization depth, and chloride ion penetration resistance of the three-component lightweight aggregate mortar were measured. When used together with the formulation, when 15 % of BFS and 5 % of FA were used, it was found to be positive in improving the compressive strength and durability of the mortar.

• Journal of Life Science
• /
• v.29 no.2
• /
• pp.198-201
• /
• 2019

Recently, it has been reported that Bacillus mojavensis possesses antifungal properties and plant growth-promoting activities, which are similar to the characteristics of siderophore. In this study, the siderophore produced by B. mojavensis was assessed using a solid phase extraction (SPE) cartridge and liquid chromatography quadrupole time-of-flight tandem mass spectrometry (Q-TOF MS/MS). After B. mojavensis was incubated in phenol medium for 16 hr and lyophilized, the sample was dissolved in water and loaded to an SPE cartridge to remove interferences. The cartridge was washed with 5% methanol in water and eluted with 2% formic acid in methanol sequentially. The eluted solution was evaporated under a stream of nitrogen gas and reconstituted in methanol. The reconstituted sample was filtered, and $1{\mu}l$ of the sample was assessed using Q-TOF MS/MS. The mass spectrometer was operated using the positive electrospray ionization mode. Based on the mass spectrum and tandem mass spectrum, the siderophore produced by B. mojavensis was bacillibactin, one of the catechol types of siderophore with a molecular weight of 882.2556. This siderophore analysis could provide a justification for the study of B. mojavensis as a functional food and for pharmaceutical applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.232.1-232.1
• /
• 2015

흑연 박리를 통해 형성된 탄소나노플레이트를 탄소나노튜브 합성을 위한 지지체로 적용하여 탄소나노플레이트 위에 직접 탄소나노튜브를 합성함으로써 3차원 구조의 탄소나노튜브/탄소나노플레이트 나노혼성체를 합성하였음. 흑연의 박리를 통해 탄소나노플레이트를 제조하기 위해서 층간화합물 삽입과 열처리를 통해 팽창흑연을 제조하고, 물리적 분쇄 과정과 액상 고압균질기 방법을 통해 두께 30nm 이하, 수 마이크론 크기의 탄소나노플레이트를 제조하고 동결건조 방법으로 탄소나노플레이트를 제조하였음. 제조된 탄소나노플레이트 상에 탄소나노튜브 합성을 위해서 탄소나노플레이트 표면처리 공정을 적용하였는데, 표면처리 방법 및 물질에 따라 금속 촉매의 담지량 및 담지 형상이 결정되어 합성되어지는 탄소나노튜브의 합성 수율과 합성된 탄소나노튜브의 형성이 다르게 나타났다. 표면처리 방법으로는 산처리방법, 흡착성 고분자 처리법, 무전해 도금법, 무기산화물 처리법이 적용되었다. 또한 담지되는 촉매 종류 및 함량, 조촉매 적용에 따라 탄소나노튜브 합성 거동을 분석하여 최적 촉매시스템을 구축하여 촉매담지체 질량 대비 700% 이상의 고수율의 탄소나노튜브/탄소나노플레이트 혼성체 합성법을 개발하였다.