• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5947-5955
• /
• 2013

This study was intended to estimate the axial deformation of joint between pavement modules in the rapid-constructible modular pavement system, and to investigate the applicability of two-phase composites for a joint material, which was composed of cement paste, epoxy, or polyurethane as a matrix and sand as particles. A case which had supports under the pavement module as well as a case which the module was put on roadbed directly were considered in FEM analysis for the axial deformation. The effect of self-weight, live load, thermal change, and drying shrinkage were estimated and the thermal change was found to cause the largest deformation compared to the others. Deformation capacity of two-phase composites was predicted using the modified shear-lag model. In the analytical results for the elastic modulus and maximum tensile strain with different volume fractions of sand, 20~30 % replacement of sand was revealed to satisfy the required strain capacity with economy when if the width of joint was designed to be 15~20 mm.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.971-976
• /
• 2004

하천유지를 위한 하천내 최소유량의 충족은 사실상 환경문제에 제공되는 것으로서 기본적으로 하천변 수생식물의 생태계 서식처를 유지하거나 복원하기 위해 제공된다. 또한 하천유지유량은 하천의 고유종 동${\cdot}$식물을 보전하고, 아름다운 하천에 대한 심미적 질을 유지하며 여가활동 및 상업적 어획고를 최대로 늘릴 수 있거나 과학적 또는 문화적 관심사의 특성을 보호하는 기능을 위한 목적으로도 제공된다. 그러므로 생태학적인 하천유지유량 차원에서 무엇보다 중요한 것은 충분한 물을 확보하고 쾌적한 하천을 유지할 수 있는 맑은 물을 하천에 흐르도록 하는 것이다. 이와 더불어 하천의 생태학적인 측면에서는 서식지 보호를 고려한 계획이 뒷받침되어야 할 것이다. 기존의 개발은 하천정비, 골재채취, 수중 보와 하구 둑 등 하천시설물 건설, 그리고 댐 및 교량건설 등 인위적인 요인에 의하여 하천환경이 심각하게 변화는 경우가 많다. 특히 댐 건설로 인해 하류지역에 수리학적 변화와 하상 변동 등이 발생하고, 이로 인하여 생태계의 변화를 초래하기도 한다. 따라서 본 연구에서는 금강 최상류에 건설된 용담다목적댐에 의해 인위적으로 하천유입량이 감소하고 이로 인해 발생할 수 있는 수리학적 변화를 모의하여 댐 건설이 금강 상류에 미치는 영향을 분석하고자 한다. 이를 위해 2차원 유한요소모형을 이용하였으며, 댐 건설전 자연유출량 및 댐 건설후 하천유지유량에 의한 하천의 건조면적, 습지면적을 산정하였다. 또한 하천의 한계소류력과 하도를 형성하는 재료에 따라 바닥면 전단응력을 산정하여 그 차(差)를 활용하여 유량에 따른 유사이송현황을 모의하였다. 모의된 결과를 visual하게 표현하고자 GIS 기법을 이용하여 주요구간에 대한 유사이송현황을 도시하였다.유역의 고도차를 이용한 흐름특성 분석을 위해 수치고도자료를 이용하여 유역흐름특성을 분석할 수 있는 TOPAZ(Topographic PArameteri-Zation) 프로그램을 이용하였다. TOPAZ 프로그램을 통해 분석된 각 격자별 분포형 수문 매개변수는 적합한 관계식을 통해 분포형 유출량을 모의하는데 적용된다.다 정확한 유입량 예측이 가능할 것으로 사료된다.이 작은 오차를 발생하였으며, 전체적으로 퍼프 모형이 입자모형보다는 훨씬 적은 수의 계산을 통해서도 작은 오차를 나타낼 수 있다는 것을 알 수 있었다. 그러나 Gaussian 분포를 갖는 퍼프모형은 전단흐름에서의 긴 유선형 농도분포를 모의할 수 없었고, 이에 관한 오차는 전단계수가 증가함에 따라 비선형적으로 증가하였다. 향후, 보다 다양한 흐름영역에서 장${\cdot}$단점 분석 및 오차해석을 수행한 후에 각각의 Lagrangian 모형의 장점만을 갖는 모형결합 방법을 제시할 수 있을 것으로 판단된다.mm/$m^{2}$로 감소한 소견을 보였다. 승모판 성형술은 전 승모판엽 탈출증이 있는 두 환아에서 동시에 시행하였다. 수술 후 1년 내 시행한 심초음파에서 모든 환아에서 단지 경등도 이하의 승모판 폐쇄 부전 소견을 보였다. 수술 후 조기 사망은 없었으며, 합병증으로는 유미흉이 한 명에서 있었다. 술 후 10개월째 허혈성 확장성 심근증이 호전되지 않아 Dor 술식을 시행한 후 사망한 예를 제외한 나머지 6명은 특이 증상 없이 정상 생활 중이다 결론: 좌관상동맥 페동맥이상 기시증은 드물기는 하나, 영유아기에 심근경색 및 허혈성 심근증 또는 선천성 승모판 폐쇄 부전등을 초래하는 심각한 선천성 심질환이다. 그러나 진단 즉시 직접 좌관상동맥-대동맥 이식술로 수술

• Korean Journal of Environmental Biology
• /
• v.38 no.3
• /
• pp.371-387
• /
• 2020

This study was conducted to investigate the flora of Mt. Unbongsan in the basalt areas of Korea. From the results of eight field surveys undertaken from March to October 2017, we identified 404 total taxa, representing 364 species, seven subspecies, and 33 varieties, which were placed in 256 genera and 91 families. The plant formation of Mt. Unbongsan is a deciduous broad-leaved and conifer mixed forest, which is common in the middle part of the Korean peninsula. Most of the mountain is covered by a young secondary forest, which is mainly composed of Quercus monglica and Pinus densiflora. Out of these 404 taxa, 193 were the first records for the region, six were endemic to Korea, three were listed on the Korean Red List of threatened species, 34 were floristic target species, and 40 were invasive alien species. The naturalized index(NI) percentage was 9.9%. Mt. Unbongsan has plant diversity, which was associated with the geomorphological landscapes. We considered that the composition and distribution of the species were affected by different environmental factors according to the presence of granite, taluses, block streams, drying ridges, valleys, puddles, wetlands, and streams.

• Journal of Food Hygiene and Safety
• /
• v.25 no.1
• /
• pp.73-78
• /
• 2010

This research was conducted to assess applicability of photostimulated luminescence (PSL) and Thermoluminescence (TL) methods for investigation of infant and young children products, nut, seasoned dried fish, spice, dried fruits, fruit & vegetable, grain and marine products, which are not approved for irradiation in Korea. PSL results show that the photon counts of non-irradiated samples were lower than 700, while those of irradiated samples were higher than 700. In TL measurement, TL ratio of irradiated samples were higher than 0.1 or ones can decrease below 0.1 whereas the temperature range of TL Glow curve was between $150{\sim}250^{\circ}C$. Monitoring result about 8 class of 325 not approved to irradiated foods, photon counts of samples were less than 700, and after re-irradiation TL Ratio ($TL_1/TL_2$) through re-irradiation step at 1 kGy were higher than 0.1 for the all samples. Therefore, these results suggested that PSL and TL measurements were useful detection methods for 8 class food products not approved to irradiation in Korea and all sample (325 cases) were not irradiated when we analysed by PSL and TL methods.

• Horticultural Science & Technology
• /
• v.18 no.6
• /
• pp.839-844
• /
• 2000

In developing of soil wetting agents using the mixture of polyoxyethylene octylphenyl ether [$C_8H_{17}O$ $(C_2H_4O)_{10}H$, POE] and polyoxyethylene+polypropyleneoxide tridecylether (1:1, w/w, CM-1), the effect of base carriers such as zeolite and vermiculite on changes of concentration of POE and on initial wetting of peat-vermiculite media were determined. The concentration of POE in the treatment of zeolite was higher than that of vermiculite. The treatments of POE+CM-1 with zeolite or vermiculite as carrier were effective in initial water retention of root media having about 510 mL of water per pot, where those of AquaGro and control had 490 mL and 400 mL of water per pot, respectively. In the evaporative water loss, the treatment of zeolite and AquaGro were faster than those of control and vermiculite. The treatment of AquaGro had faster water movement in root media than those of POE+CM-1 regardless of carriers and same trends were observed in the volume of water infiltrating into root media. Also, increasing the amount of POE+CM-1 resulted in increased water retention capacity, evaporative water loss, water movement in root media and amount of water infiltrating into root media.

• Analytical Science and Technology
• /
• v.30 no.5
• /
• pp.234-239
• /
• 2017

Identifying the components of residues that are not completely burned at the sites of fires site can provide valuable information for tracing the causes of fires. In order to clarify the types of plastic combustion residues found at the scenes of fires, we studied the residue formed after the combustion of polyethylene (PE) and acrylonitrile butadiene styrene (ABS). Plastic samples were burned at 200, 300, 350, 400, and $500^{\circ}C$ for 3 min using a cone calorimeter, and the changes in weight and combustion products were observed. The powder products obtained by lyophilization and pulverization of the combustion products obtained at each temperature were analyzed by a Fourier transform-near infrared (FT-NIR) spectrometer. When the PE samples were burned, the weight did not change up to $350^{\circ}C$, however a significant change in the weight could be measured above $400^{\circ}C$. The principal component analysis (PCA) of the FT-NIR spectra of the PE and ABS samples obtained at each temperature confirmed that the combustion residues at each temperature were PE and ABS, respectively. Therefore, the types of unburned plastics found at the sites of fires can be confirmed rapidly by near infrared spectroscopy.

• Journal of Sensor Science and Technology
• /
• v.11 no.2
• /
• pp.102-110
• /
• 2002

The chemical and mechanical characteristics of a new surface modifier, dichlorodimethysilane (DDMS, $(CH_3)_3SiCl_2$), for stiction-free polysilicon surfaces are reported. The main strategy is to replace the conventional monoalkyltrichlorosilane(MTS, $RSiCl_3$) such as octadecyltrichlorosilane (ODTS) or 1H,1H,2H,2H-perfluorodecyltrichlorosilane (FDTS) with dialkyldichlorosilane (DDS, $R_2SiCl_2$) with twit short chains, especially DDMS. DDMS, with shorter chains in aprotic media, rapidly deposits on the chemically oxidized polysilicon surface at room temperature and successfully prevents long cantilevers of 3 mm in length from in-use as well as release stiction. DDMS-modified polysilicon surfaces exhibit satisfactory hydrophobicity, long term stability and thermal stability, which are comparable to those of FDTS. DDMS as an alternative to FDTS and ODTS provides a few valuable advantages; ease in handling and long-term storage in solution, low temperature-dependence and low cost. In addition to the new modifier molecule, the simplified process of direct release right after washing the modified surface with isooctane was proposed to cut the processing time.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.157-169
• /
• 2009

The aim of this study was to evaluate effect of implant abutment screw coating treatment on joint stability, investigating mechanical properties of these. For this study used $ExFeel^{(R)}$ external hexed implant system and $15mm{\times}1mm$ discs. Experimental group was $1{\mu}m$ TiN, TiCN, TiC coated abutment screws and discs. To know mechanical property, i evaluated adhesion strength, surface hardness, using disc, corrosion test using screw. The results were as follows : rotation angle of coated screws increased than that of non-coated screw because of lower friction coefficient, especially TiC coated screw group had the largest value, but removal torque decreased in all coated screws (p<0.05). Torque loss before and after fatigue test was the smallest in TiC-coated screws, and the largest in non-coated screws (p<0.05), and there was no statistically significant difference between dry condition and wet condition of screws because of higher surface hardness and lower friction coefficient. From the above results, TiN, TiCN, TiC coating group had high abrasion resistance, especially TiC coated group which had low torque-consuming, high rotation angle as low friction coefficient will be considered to influence on implant abutment screw joint stability positively.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.183-190
• /
• 2009

The aim of this study is to find the condition of forming the favorable nanotubes by anodizing with NaF and $H_3PO_4$. Machined Ti discs were used for anode, and Platinum net was used for cathode. For electrolyte, $H_3PO_4$ and NaF solution were mixed. We controlled voltage, electrolyte concentration, anodizing time and formed nanotubes on Ti discs. After that, these were washed with distilled water for 24 hours and dried in the $40^{\circ}C$ oven for 24 hours. The surface structure of specimens were analyzed. The results were as follows : At 0.5 wt % NaF, according as increasing voltage and anodizing time, early state of nucleating pores were generated. At 1.0 wt % NaF, 20 V, 20 & 25 min, well-formed nanotubes were observed. At 1.0 wt % NaF, 30 V, structure of nanotube became bigger and interconnected. At 2.0 wt % NaF, no nanotubes were formed and it was unrelated with voltage and time. At 1.0 wt % NaF, 20 V, 20 - 25 min, well-ordered nanotubes were generated on Ti discs. For the formation of favorable nanotubes, it is considered that proper parameters such as electrolyte concentration, voltage, anodizing time are necessary according to the kind of electrolytes.

• Asian Journal of Turfgrass Science
• /
• v.22 no.2
• /
• pp.133-140
• /
• 2008

The growth of root and shoot normally decline dramatically in mid-summer of Korea, moreover the cool-season turfgrassgrass eventually wither to death over $30^{\circ}C$. The increase of air temperature also drives the heat of soil, that makes stress on root system. The heat stress affects physiological mechanisms of hormonal unbalance that stimulates shoot growth, photosynthesis, and transpiration. To solve those problems, many studies have been carried out to control soil moisture and OM content to decrease soil temperature for dissolving the growth retardant by heat stress. This study initiated to analyze the change of soil temperature with soil moisture, and the effect of soil depth and moisture content on heat transmit and thermal changes on turfgrass growth(productivity, green color, and damage by dryness and high temperature). Kentucky bluegrass plots prepared with 25%, 33%, 40% soil moisture treatments. Soil temperature was measured every five min. with four thermo-sensors at 12 and 2 cm soil depth. The most acceptable growth showed at 33% soil moisture, but the worst result showed at 40%. The soil moisture seriously affected on the growth of Kentucky bluegrass, however the quality of turfgrass may acceptable if we can control soil moisture down to 33% when the flooding season of monsoon.