• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.5-7
• /
• 1974

1. This study indicates that above the fiber saturation point the drying rate can be increased with increasing the velocity of the air circutation, i.e., the drying rate of sample boards is proportional to the air velocity, but below the fiber saturation point, the effect of the velocity of air circulation is very low as shown in Figs. 1 and 2. 2. Under the controlled temperature and humidity in the kiln, the more the sample boards have moisture, the higher drying rate of it can be obtained. In other words, this means that even though in the case of drying various moisture content of wood, at the final drying stage, approximately the same percentage of moisture content of wood can be secured by employing the higher velocity of air circulation. 3. This study shows that the rate of drying in kiln changes distinctly at the fiber saturation point, i, e., above the fiber saturation point, the drying curve shows concave aginst the X axsis, but below the fiber saturation point, in the range from 30 percent of moisture content to 20 percent of moisture content, the curve shows convex as shown in Fig. 3. As the drying progresses, however, the drying curve shows concave again below 20 percent of moisture content. This means that inflection point of drying curve may be located clearly at the fiber saturation point, i.e., 30 percent of moisture content. As mentioned above, the 30 percent of moisture content of wood at which the inflectional point appears can be recognized as a critical point, i. e., the fiber saturation point at which all free water was removed from wood. The existence of inflectional point indicates that the evaporation of hygroscopic water in a cell wall is more difficult than the evaporation of free water in a cell cavity and the minor space of cell wall. The convex curve in the range of moisture content from 30 percent to 20 percent means that the evaporation of capillary condensed water has a tendency of the same rates of drying approximately, but as approaching to the 20 percent of moisture, the transfusion of moisture from wood becomes difficult because of having less moisture in cell wall. Below 20 percent of moisture content, the drying curve shows concave again, which means that it is difficult to remove the moisture located nearer to the surface of cellulose molecules and the surface bound water. These relations were revealed in Fig. 4. In comparison AC curve which does not have the two inflection points with BD curve which has two inflection points, i.e., Band D, they are mentioned already, by existence of the inflection points, the curve BD shows that the change of drying rate in the interval from 20 percent of moisture content to 30 percent of moisture content is not greater than in the case of the curve AC in the same interval. At the inflection point of 30 percent of moisture content, it can be noticed that the changing of the drying rate is very conspicuous. This phenomenon also can be recognized, as it is noticed by the Fig. 3, the drying rate from green to 30 percent of moisture content is very great. But the inclination of the curve is very slow from 30 percent of moisture content to 20 percent of moisture content, i.e., the inclination of the curve becomes almost horizontal lines. Acknowledgments Gratitude is expressed to Fred E. Dickinson, Professor of 'Wood Technology, School of Natural Resources, University of Michigan, USA for his suggestion to carry out this study.

• The Journal of Engineering Geology
• /
• v.34 no.1
• /
• pp.137-146
• /
• 2024

The pertinent Korean Industrial Standard (KS F) requires that rocks dried at 105 ± 5℃ be taken out of the oven into air and weighed on a scale. However, when rocks are exposed to air after the drying process, they absorb moisture, meaning that their weight will increase. In this study, eight cubic samples of Hwangdeung granite of different sizes were used to measure and compare the dry weight. The dry singularity weight measured in air was smaller than that measured in the drying oven. The difference in dry weight showed a positive correlation with sample size. Conversely, the difference in dry weight per unit weight of rock showed a negative correlation with sample size. The weight of a rock sample exposed to air is determined by the magnitude of the influence of convection currents occurring around the heated rock and the influence of moisture absorption in air. A singularity occurs when the magnitudes of these two effects are equal. The larger the rock sample, the longer the time taken for the singularity to occur, the greater the weight loss of the sample, and the longer the time taken for the sample to return to the initially measured weight on account of the greater moisture absorption for larger samples than smaller samples. In the future, research into the singularity and dry weights measured inside the drying oven will help to identify and address the limitations of the current KS F testing regulations.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.3
• /
• pp.5-14
• /
• 2023

The dry unit weight of the soil can be obtained by measuring the weight of the oven dried soil. According to the Korean Industrial Standards (KS F), oven dried soil at 110±5℃ continuously increases in weight when exposed to air. However, there is no regulation on the weight measurement time of oven dried soil, making it difficult to accurately measure the dry weight. In this study, a method to easily determine the dry weight was presented through the analysis of the weight singularity that appears during weight measurement. The weight singularity represents the smallest value among the measured weights, and is the weight at which the effect of moisture absorption in the air of the sample is minimized. In the course of the experiment, a container was selected using a statistical analysis method, and a photograph of the soil samples were presented using an optical microscope. In addition, the temperature of the weight singularity was measured using a non-contact infrared thermometer. As a result of analyzing the weight singularity of six types of soil, including Jumunjin sand, Naeseong stream sand, Yecheon weathered granite soil, Jeju sand, Sabkha sand, and Ulleung sand, the weight singularity of oven dried sample appeared between 8 and 27 seconds after weight measurement, and the temperature ranged from 103.4 to 108.13℃. The weight decrease rate of the singularity was 0.0066 to 0.0085% depending on the soil samples.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.9
• /
• pp.25-32
• /
• 2023

The Korean Industrial Standards (KS F) have a various regulations for measuring the weight of dried soil and rock. However, if the dried weight is measured in air after drying at 110±5℃ or 105±5℃, a weight singularity occurs, in which the weight decreases and then increases as the measurement time continues. In this study, basaltic rock from Ulleung Island was oven dried at 40 to 110℃. The weight was measured on an electronic scale with a sensitivity of 0.0001g (0.1mg) to find weight singularities. A method to easily determine the dry weight using the weight singularities was presented. As a result of analyses of the singularity of rock specimen according to temperature, the singularities were appeared in the temperature range of 40 to 110℃, and the weight of the singularity was smaller as the heating temperature increased. In particular, the weight singularity duration appeared, and the duration of the singularity was shorter as the heating temperature increased. The results of the convection measurement experiment showed that the cause of the singularity is the convection phenomenon caused by the contact of the heated rock with the air. The weight decrease of oven dried rock occurs when the effect of convection is dominant over the effect of air moisture absorption. Conversely, the weight increase of rock occurs when the effect of air moisture absorption is dominant over the effect of convection.

• Korean Journal of Soil Science and Fertilizer
• /
• v.16 no.2
• /
• pp.168-178
• /
• 1983

Influence of several dehydration treatments on original structure and water behavior in the process of drying were investigated employing three hawaiian volcanic ash soils and four synthetic minerals. These three soils were developed under different rainfall condition and contained three different amount of amorphous materials in them. Measurement of water losses by oven drying at $105^{\circ}C$, $P_2O_5$ drying, freeze drying, and critical point drying revealed that more water losses were noted by oven drying than by three other drying techniques and the differences of water losses between oven and $P_2O_5$-drying were closely related to amoun: of amorphous materials in them, showing the order of Kaiwiki > Hilo > Kawaihae. This indicates that dehydration of amorphous materials by elevated temperature ($105^{\circ}C$) excluded water beyond that in the adsorbed (hygroscopic) state. The effect of dehydration treatments on initial structure was visualized by scanning electron microscopy. The micrographs showed that oven-and $P_2O_5$-dried samples formed into large mass of sub-angular blocky, dense, and closed crumbs, while the freeze dried and critical point dried samples resulted in less shrinkage, and small, fluffy and open spongy structure. However, critical point drying technique produced bulkier, softer, and greater open structure samples than even freeze drying. Additional Index Words: original structure, synthetic minerals, critical point drying, $P_2O_5$ drying. 1. This is a part of author's Ph.D. dissertation submitted to the University of Hawaii, Honolulu, Hawaii 96822 in 1979. 2. Professor of Agricultural Chemistry, Korea University.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4030-4037
• /
• 2011

The purpose of this study was to investigate the correlation between oral dryness and stress and to collect baseline data for health promotion plan of college students. This research design is correlation study. Data of 835 were collected from May 2 to June 17, 2011, and analyzed using the SPSS PASW Statistics 18.0 Program. There was a statistical significant between oral dryness and perceived health status(p<.001). there were statistical significant in gender(p<.001), age(p<.001), grade(p<.01), major(p<.01), perceived health status(p<.001), exercise(p<.001), smoking(p<.001), drinking(p<.01) between general characteristics and stress. The mean score of oral dryness level was $12.89{\pm}10.15$ from 0 to 60 score range. Higher percentage in oral dryness action was "When I swallowing dry food, drink water or beverage"(48.7%). The mean score of stress was $7.17{\pm}4.78$ from 0 to 20 score range. Oral dryness level was positively related to stress(p<.01) and oral dryness action(p<.001). It is necessary to develop the educational program for health promotion of college students.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.54-54
• /
• 2011

방사 공정 최적화를 위해 칩(chip)건조를 실시하여 칩의 수분을 모두 제거한 후 실험을 진행하게 된다. 칩은 그 자체가 공정수분율(0.4%) 또는 그 이상의 수분을 함유하고 있으므로 건조하지 않고 방사하면 현저히 가수분해가 일어난다. 가수분해가 일어난다면 PET 분자량도 저하되어 고분자의 성질을 잃게 되어 방사된 섬유의 물리 화학적 성질에 중요한 영향을 받게 된다. 그러므로 가수분해를 방지하기 위하여 칩내 수분을 제거하는 건조 공정을 거치는 것이다. 개발된 나노은입자을 함유한 Ag/PET 마스터배치의 제사성 및 가연성 평가을 위한 파일럿연구를 행했다. 본 연구에서 사용한 은나노 M/B 칩(chip)의 경우 일반적으로 사용하는 PET 칩에 비하여 낮은 고유점도를 가지므로 방사성에 칩의 수분이 더욱 영향을 미칠 것이라 판단되어 건조공정에 특별한 주의을 하여 진행하였다. 마스터배치의 고유점도(IV)값의 변화에 따른 제사성 및 가연성 평가를 관찰하였다. #3 M/B 칩의 제사성이 #1 M/B 칩 대비 공정성이 개선되어 두 품종 모두 비출사가 발생하지 않았으며, M/B 제조시 분산제 유무에 따른 방사공정성의 차이는 없는 것으로 보인다. 따라서 #1 M/B 대비 공정성이 개선된 점은 M/B의 IV개선에 기인하는 것으로 판단되었다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.22 no.1
• /
• pp.60-69
• /
• 1996

3-APPA는 생체내 물질 Υ-amino butyric acid와 유사한 구조를 갖는 물질로서 human fibroblasts 3-dimensional culture system 등의 in vitro 시험에서 collagen 합성촉진 효과, 세포증식 효과를 나타내며, hairless mouse를 이용한 동물시험에서도 collagen 합성이 증가되는 것으로 보고된 바 있다. 또한 피부 안정성에서도 우수한 결과를 보여줌으로서 화장품 분야에서 새로운 노화억제 물질로서 주목을 받게 되었다. 본 시험에서는 180명의 피검자를 대상으로 3개월간의 임상시험을 통하여 새로운 노화억제 물질인 3-APPA의 효능을 기존의 GABA 유사물질, aminopropane sulfonic acid와 비교하였다. 본 시험은 double-blind, randomized, vehicle-controlled clinical study로서 180명의 피검자를 APSA군, 3-APPA군, vehicle군으로 분류한 후 3개월간 매일 저녁 취침 전, 안면에 시험제품을 사용하도록 하였으며, 사용 전, 사용 1주후, 2주후, 6주후, 12주후 5회 설문지를 통하여 피부상태를 조사하였다. 각 설문내용은 피부 건조도, 피부 탄력도, 피부 주름량, 피부 윤기도, 피부 거칠기 정도에 대한 5개 질문으로 구성된 효능에 관한 질문과 흡수정도, 끈적임, 매끄러움, 보습력, 보습지속성, 전체적인 사용감에 대한 6개 질문으로 구성된 사용성에 관한 것이었다. 각 질문에 대하여는 매우 좋음 1점, 좋은 2점, 보통임 3점, 나쁨 4점, 매우 나쁨 5점 사이에서 답할 수 있도록 하였다. 시험 결과 APSA군은 6주와 12주후 피부 건조도, 피부 거칠기 항목에서 사용전에 비하여 유의한 차이를 나타내었다. 3-APPA군은 6주후 피부 건조도, 피부 거칠기, 피부 탄력도 항목에서 시료사용전에 비해 유의한 차이를 나타내었으며 12주후에는 피부 건조도, 피부 탄력도, 피부 윤기도, 피부 거칠기 항목에서 유의한 차이를 나타내었다. 12주후 APSA군은 피부 주름, 피부 탄력도 항목에서 vehicle 사용 피검자군에 비하여 유의적인 차이를 나타내었으나 3-APPA군은 피부 탄력도, 피부 주름량, 피부 윤기 항목에서 vehicle군에 비하여 유의적인 차이를 나타내었다. 결론적으로 3-APPA와 APSA 사이에 유의적인 차이가 있지는 않았으나 3-APPA군은 APSA군에 비하여 6주, 12주에서 사용전과 유의한 차이를 나타내는 항목이 많았으며 12주에서 vehicle과 유의적인 차이를 나타내는 항목도 많으므로 3-APPA가 APSA 보다 광범위한 피부노화 억제 효과를 갖는 물질이라고 할 수 있다.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.1
• /
• pp.170-174
• /
• 2021

The purpose of this study is descriptive survey to quality of life by dry eyes experience in university students. The Korean version of the National eye institute visual functioning questionnaire (NEI-VFQ) was used to evaluate the quality of life. As a result of the study, 18.4% of the participants were diagnosed with dry eyes, and 63.2% experienced subjective dry eyes experience. The findings showed that the factors influencing the visual quality of life was wearing glasses, and the explanatory power for this 13.6%. Further research is needed considering the length of wearing glasses, contact lenses and severity of dry eyes.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.2
• /
• pp.88-109
• /
• 2020

This study aimed to distinguish categories of archival information and identify properties by their detail types, so that the various forms of architectural heritage information generated can be managed based on their attributes and characteristics. First, the specific uses of terms in the legal system were reviewed and their associated concepts specifically defined. "Architectural heritage" was defined as architecture belonging to the category of tangible cultural heritage as designated by law, and "architectural heritage archival information" was defined as all kinds of material expressed by electronic processing of the actual status for preservation and management. Next, the production status of architectural heritage archival information was reviewed in relation to the legal system. This confirmed that relevant legal systems were organized hierarchically and that various types of archival information were generated in a single project. Furthermore, it was confirmed that even archival information produced in the same form contained differing contents depending on the specific purpose and method, and that there was no classification by which to cover all archival information. Finally, it was also confirmed that detailed drawing types could be categorized according to the purpose of production and the target of the records. Based on the findings of this review, the type and properties of archival information were presented as the primary classification criteria, and the architectural heritage archival information was divided into 6 general types and 27 detailed types. Specifically, the linguistic form, dimension, temporal property, and graphic form of archival information were applied as criteria for the classification of general types, and the target, production purpose, production method of archival information, and content characteristics of archival information properties of archival information by type were comprehensively reviewed.