• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1417-1425
• /
• 1991

본 연구에서는 파괴역학적 개념을 도입하여 수평 회전체에 존재하는 횡방향 개폐균열의 모형을 설명하고 균열거동을 분석하였으며, 균열의 깊이, 회전속도 및 회 전방향에 따른 균열선단에서의 응력확대 계수를 계산하고 그 특성을 분석하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.4 s.247
• /
• pp.442-450
• /
• 2006

This paper describes the new modal analysis method to detect the presence of the breathing crack in a general rotor system with disk asymmetry and stator anisotropy. It is proposed that the modal analysis using directional frequency response functions (dFRFs), which, accounting for the directivity in modes, clears the heavily over-lapping of other harmonics occurring from non-isotropic properties in addition to those due to crack, can provide an effective method to detect the modes by a crack. The simulations from the simple general rotor model show that the r-dFRFs (reverse dFRFs) for asymmetry confirms a good indicator of the presence of the breathing crack and the instability is primarily influenced by the shaft asymmetry than the breathing crack.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.3
• /
• pp.74-83
• /
• 2001

After the concept of fracture mechanics was applied to fatigue crack propagation by Paris. Paris' law is widely used to predict fatigue crack growth behavior. Since Elber proposed the effective stress intensity factor(SIF) and showed a good agreement with experimental results using the proposed SIF, emphasis in crack propagation studies has been placed on measuring the effective stress range ratio. This paper proposes a numerical model to simulate the crack closure and propagation behaviour under various loading spectrum. The validity of the proposed model is checked by comparing with the Toyosada numerical solutions on the crack propagation behaviour. Important insights developed are summarized.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.35-46
• /
• 2008

Harmonic vibration characteristics for the general rotor model having a breathing crack are analyzed. Analyses are performed at the half critical speed ranges. The vibration characteristics are explained by using the additional slope and bending moment at the crack position and the influence coefficient showing the structural dynamic characteristics of the rotor. With the low crack depth the magnitude of the additional slope is kept constant even at the speed range at which the orbit magnitude is very sensitive to the rotational speed change. At this speed range the vibration is affected by the influence coefficient only. As the dynamic bending moment exceeds the static bending moment with the increase of crack depth. the additional slope affects the vibration amplitude of cracked rotor and the crack propagation rate increases.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.10 s.103
• /
• pp.1137-1147
• /
• 2005

The dynamic response due to the unbalance and crack and the quasi-static response due to gravity are analytically derived based on the complex transfer matrix. The additional slope is expressed as function of the bending moment at crack position based on the fracture mechanics concept, and inversely the bending moment is expressed as function of the additional slope at the crack Position. At each angle step during the shaft revolution, the additional slope and bending moment are calculated by an iterativemethod. The transient behavior is considered by introducing Fourier series expansion concept for the additional slope. Simulation is carried out for a simple rotor similar to those available in the literature and comparison of the basic crack behavior is shown. Using the additional slope, the cracked rotor behavior is explained with the crack depth increased: the magnitude of the additional slope increases and the closed crack duration during a revolution decreases as the crack depth increases. The direction of unbalance is also shown as a factor to affect the crack breathing. Whirl orbits are shown near the sub-critical speed ranges of the rotor.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.3
• /
• pp.84-92
• /
• 2001

The development of a crack propagation simulation model in consideration of crack closure behavior was discussed in the accompanying paper by the authors, Kim et al(2001). To verify crack propagation behavior under variable amplitude loading based on the model, calculations of effective crack driving stresses and corresponding propagation lives are carried out for load spectrums with various stress ratios, overload and underload. Good agreement is confirmed between test results in the literatures and simulations using the developed model.

• JOURNAL OF ELECTRICAL WORLD
• /
• no.6 s.138
• /
• pp.89-92
• /
• 1988

변압기 1차측에는 과부화 보호를 위한 고압 컷 아웃이 사용되고 여기에 텐션형 퓨즈가 장착되어 있다. 고압 컷 아웃은 전류개폐능력 관계로 300kVA 이하인 변압기에 사용된다. 변압기 운전중은 고압 컷 아웃의 내부점검을 할 수 없기 때문에 통상은 눈으로 외시점검을 하는 것이 일반적이다. 고압 컷 아웃의 사고로는 퓨즈 용단, 애자부의 균열, 오손 등으로 인한 지락이나 접촉 칼날부의 접촉 불량, 본체의 파손 등이 있다. 이러한 사고를 사전에 발견하기는 곤란한 경우가 많은 것 같다. 이러한 사고를 사전에 발견하기는 곤란한 경우가 많은 것 같다. 다음은 고압 컷 아웃이 파손해서 정전된 사례이다.

• Magazine of the Korea Concrete Institute
• /
• v.3 no.3
• /
• pp.149-157
• /
• 1991

This paper concentrates on the nonlinear analysis of the reinforced concrete flexural members under cyclic loading. To develop a nonlinear material model, concrete is treated as an orthotropic nonlinear material and steel is modeled as an elasto-plastic material. The models for hysteresis behavior with stiffness degradation in compression and for crack opening and closing in tension are included. The finite element computer program for the nonlinear analysis of RC flexural members under cyclic loading is developed. The accuracy and reliabihty of the numerical procedure IS demonstrated by the FEM analysis and test results of underreinforced concrete beams.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1264-1265
• /
• 2011

본 논문은 가스 절연 차단기를 대체하는 고체 절연체의 성형 시 발생하는 집중 열응력에 의한 고체 절연체의 기계적 특성에 관한 연구 결과이다. 친환경 문제가 대두되고 전기 산업에서 고객은 좀 더 안정적이고 안전한 전기 공급이 필요시 됨에 따라서 고체 절연 개폐기 및 차단기의 수요가 늘어남에 따라 고체 절연체의 생산 불량률이 이슈화가 되고 있다. 특히 성형 시 발생되는 열응력 및 거동으로 인하여 절연체의 균열 및 내부 진공 인터럽터의 파손 등으로 경제적 비용 손실의 문제가 발생하게 되어 집중 응력을 피할 수 있는 합리화 구조에 대한 연구가 진행되었다.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.1
• /
• pp.81-87
• /
• 1990

Fatigue crack closure levels based on the behavior of residual displacements on crack surfaces, are determined analytically according to the microscopic crack closure mechanisms, i.e., whether the first contact of crack surfaces takes place at the very crack tip or on the surfaces near the tip. The comparative analysis on the two models is carried out empirically by the constant amplitude fatigue tests on 2024-T3 aluminum alloy plate, and it shows that under negative stress ratio, the case of the first contact at crack tip gives better agreement with the experimental results than the other.