• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.6
• /
• pp.772-779
• /
• 2011

New type of syngas generator based on the partial oxidation of biogas in volumetric permeable matrix reformers was suggested as an effective, adaptable and relatively simple way of syngas and hydrogen production for various low-scale applications. The use of biogas as an energy source reduces the chance of possible emission of two greenhouse gases, $CH_4$ and $CO_2$, into the atmosphere at the same time. Its nature of being a reproducible energy source makes its use even more attractive. Parametric screening studies were achieved as air ratio, biogas component ratio, input gas temperature, Steam/Carbon ratio. As the air ratio was low, the production of the hydrogen and carbon monoxide increased in the condition that 3D matrix reformer maintains the stable driving. As it was the simulation biogas in which the carbon dioxide content is high, the flammable range became narrow. And the flammable range was extended if the injected gas was preheated. The stable driving was possible in the low air ratio. The amount of hydrogen production was increased as S/C ratio increased.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.494-502
• /
• 2016

A 1-dimensional heterogeneous reactor model with the gas-solid interfacial phase gradients was developed for the simulation of the packed bed reactor where the exothermic reversible water gas shift reaction for the natural gas steam reformed gas was proceeding in adiabatic mode. Experimental results obtained over the WGS catalyst, C18-HA, were best simulated when the frequency factor of the reaction rate constant was adjusted to a half the value reported over another WGS catalyst, EX-2248, having the same kinds of active components as the C18-HA. For the reactor of the inside diameter 158.4 mm and the bed length 650 mm, the optimum feeding temperature of the reformed gas was simulated to be $194^{\circ}C$, giving the lowest CO content in the product gas by 1.68 mol% on the basis of dried gas. For reactors more extended in the bed length, the possible lowest CO content in the product gas with the optimum feeding temperature of the reformed gas were suggested.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.571-580
• /
• 2016

In this paper, performance of the gas turbine combined cycle(GTCC) using pre-combustion carbon capture technology was comparatively analysed. Steam reforming and autothermal reforming were used. In the latter, two different methods were adopted to supply oxygen for the reforming process. One is to extract air form gas turbine compressor (air blowing) and the other is to supply oxygen directly from air separation unit ($O_2$ blowing). To separate $CO_2$ from the reformed gas, the chemical absorption system using MEA solution was used. The net cycle efficiency of the system adopting $O_2$ blown autothermal reforming was higher than the other two systems. The system using air blown autothermal reforming exhibited the largest net cycle power output. In addition to the performance analysis, the influence of fuel reforming and carbon capture on the operating condition of the gas turbine and the necessity of turbine re-design were investigated.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.1
• /
• pp.89-96
• /
• 2015

n-octadecnae based shape stabilized phase change material (SSPCM) was prepared by using vacuum impregnation method. And an exfoliated graphite nanoplate (xGnP) which has high thermal conductivity properties is used as a PCM container. And then we made heat storage concretes which contains SSPCM for reducing heating and cooling load in buildings. In the prepararion process, the SSPCM was mixed to a concrete as 10, 20 and 30wt% of cement weight. The thermal properties and chemical properties of heat storage concrete were analyzed from Scanning electron microscope (SEM), Fourier transformation infrared spectrophotometer (FT-IR), Deferential scanning calorimeter (DSC), Thermogravimetric analysis (TGA) and TCi thermal conductivity analyzer. And we conducted surface temperature analysis of SSPCM and xGnP by using heat plate and insulation mold.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.97-97
• /
• 2015

전 세계적으로 화석연료의 고갈 및 환경오염 문제를 해결하기 위해 신재생에너지에 대한 관심이 급증하고 있다. 이러한 신재생에너지에는 수소 에너지, 자연 에너지(태양열, 지열 등), 바이오 매스 에너지 등이 포함된다. 이 중 수소 에너지는 지구상에 풍부하게 존재하고 있는 물과 탄화수소로부터 얻어지며, 연소 시에도 다시 물을 형성하여 오염 물질을 배출하지 않는 차세대 무공해 에너지원으로써 주목을 받고 있다. 수소 제조를 위한 공정에는 수증기 개질 공정(steam reforming), 부분 산화(partial oxidation) 및 자열개질(autothermal reforming) 등이 있으며 실제로 생산되는 대부분의 수소는 탄소/수소비(1:4)가 높은 메탄($CH_4$) 가스를 이용한 메탄 수증기 개질 공정(steam methane reforming)을 통하여 제조된다. 이 때 수소 제조의 고효율화 및 저비용화를 위해서는 반응물에 대한 높은 선택도, 고활성도 및 높은 안정성을 갖는 촉매가 반드시 필요하며, 대표적으로 Ni, Pt, Ru 등이 보고되고 있다. 이러한 촉매들은 대부분 세라믹 pellet 형태로 제작되어 왔으나 열전도도가 낮고 물리적 충격에 취약하다는 단점이 존재한다. 따라서 우리는 이러한 단점을 극복하고, 촉매의 활성을 높이기 위하여 다공성 금속 합금 폼을 촉매 지지체로 도입하였다. 또한, 다공성 금속 합금 폼 표면에 촉매의 분산 및 안정성을 향상시키기 위해 지지체와 촉매 사이에 원자층 증착법을 이용하여 inter-layer를 도입하였다. 이들의 구조, 형태, 및 표면의 화학적 상태는 주사전자현미경, EDS (energy dispersive spectroscopy)가 탑재된 주사전자현미경, X-선 회절, 및 X-선 광전자 분광법을 이용하여 규명하였다. 더하여 정전압-전류 측정법 및 유도 결합 플라즈마 분광 분석기을 이용하여 전기 화학 반응을 유도하고, 반응 후 전해질의 성분분석을 통해 촉매와 지지체 간의 안정성을 평가하였다. 따라서 본 결과들은 한국진공학회 하계정기학술대회를 통해 좀 더 자세히 논의될 것이다.

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.528-534
• /
• 2006

The purpose of this paper is to investigate the optimal operating condition for the hydrogen production by biogas reforming using the plasmatron induced thermal plasma. The component ratio of biogas($CH_4/CO_2$) produced by anaerobic digestion reactor were 1.03, 1.28, 2.12, respectively. And the reforming experiment was performed. To improve hydrogen production and methane conversion rates, parametric screening studies were conducted, in which there are the variations of biogas flow ratio(biogas/TFR: total flow rate), vapor flow ratio($H_2O/TFR$: total flow rate) and input power. When the variations of biogas flow ratio, vapor flow ratio and input power were 0.32~0.37, 0.36~0.42, and 8 kW, respectively, the methance conversion reached its optimal operating condition, or 81.3~89.6%. Under the condition mentioned above, the wet basis concentrations of the synthetic gas were H2 27.11~40.23%, CO 14.31~18.61%. The hydrogen yield and the conversion rate of energy were 40.6~61%, 30.5~54.4%, respectively, the ratio of hydrogen to carbon monoxide($H_2/CO$) was 1.89~2.16.

• Applied Chemistry for Engineering
• /
• v.8 no.3
• /
• pp.382-388
• /
• 1997

Reforming of propane by carbon dioxide using NiO/${\gamma}$-$A1_2O_3$ was carried out in a pulse or continuous kid bed reactor. NiO/${\gamma}$-$Al_2O_3$ showed higher dissociation ability of $CO_2$ than NiO/${\gamma}$-$Al_2O_3$, and the former exhibited higher conversion of propane than the latter. The presence of oxygen in the reaction mixture of propane and $CO_2$ increased the conversion of propane and reduced the amount of carbon deposit on the catalyst surface. Mechanical mixture catalyst of NiO/${\gamma}$-$Al_2O_3$ and $Ga_2O_3$ showed higher stability to deactivation than NiO/${\gamma}$-$Al_2O_3$ itself. The synergistic effect between NiO/${\gamma}$-$Al_2O_3$ and $Al_2O_3$ was also observed in this study.

• Journal of Korea Society of Industrial Information Systems
• /
• v.24 no.5
• /
• pp.9-16
• /
• 2019

In today's global energy market, the importance of green energy is emerging. Hydrogen energy is the future clean energy source and one of the pollution-free energy sources. In particular, the fuel cell method using hydrogen enhances the flexibility of renewable energy and enables energy storage and conversion for a long time. Therefore, it is considered to be a solution that can solve environmental problems caused by the use of fossil resources and energy problems caused by exhaustion of resources simultaneously. The purpose of this study is to efficiently produce hydrogen using plasma, and to study the optimization of DME reforming by checking the reforming reaction and yield according to temperature. The research method uses a 2.45 GHz electromagnetic plasma torch to produce hydrogen by reforming DME(Di Methyl Ether), a clean fuel. Gasification analysis was performed under low temperature conditions ($T3=1100^{\circ}C$), low temperature peroxygen conditions ($T3=1100^{\circ}C$), and high temperature conditions ($T3=1376^{\circ}C$). The low temperature gasification analysis showed that methane is generated due to unstable reforming reaction near $1100^{\circ}C$. The low temperature peroxygen gasification analysis showed less hydrogen but more carbon dioxide than the low temperature gasification analysis. Gasification analysis at high temperature indicated that methane was generated from about $1150^{\circ}C$, but it was not generated above $1200^{\circ}C$. In conclusion, the higher the temperature during the reforming reaction, the higher the proportion of hydrogen, but the higher the proportion of CO. However, it was confirmed that the problem of heat loss and reforming occurred due to the structural problem of the gasifier. In future developments, there is a need to reduce incomplete combustion by improving gasifiers to obtain high yields of hydrogen and to reduce the generation of gases such as carbon monoxide and methane. The optimization plan to produce hydrogen by steam plasma reforming of DME proposed in this study is expected to make a meaningful contribution to producing eco-friendly and renewable energy in the future.

• Korean Chemical Engineering Research
• /
• v.47 no.2
• /
• pp.243-247
• /
• 2009

This study is purposed to analyze thermodynamic properties on the hydrogen production by ethylene glycol steam reforming. Various reaction conditions of temperatures(300~1,600 K), feed compositions(steam/carbon= 0.5~4.5), and pressures(1~30 atm) were applied to investigate the effects of the reaction conditions on the thermodynamic properties of dimethyl ether steam reforming. An endothermic steam reforming competed with an exothermic water gas shift reaction and an exothermic methanation within the applied reaction condition. Hydrogen production was initiated at the temperature of 400 K and the production rate was promoted at temperatures exceeding 500 K. An increase of steam to carbon ratio(S/C) in feed mixture over 1.0 resulted in the increase of the water gas shift reaction, which lowered the formation of carbon monoxide. The maximum hydrogen yield with minimizing loss of thermodynamic conversion efficiency was achieved at the reaction conditions of a temperature of 900 K and a steam to carbon ratio of 3.0.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.715-719
• /
• 2011

The $La_{0.7}Sr_{0.3}Cr_{1-x}Ni_{x}O_{3}$(LSCN-x) perovskites were prepared by citric acid and EDTA using a sol-gel method. The LSCN-x was characterized by BET, XRD, SEM, $H_2$-TPR, EA and TEM. The catalytic performance of LSCN-x catalysts in steam reforming of propane in the temperature range 600~$800^{\circ}C$ was investigated. Propane conversion and hydrogen yield increased with an increase in the amount of added Ni up to x=0.5 in the B-site, denoted as LSCN-0.5, under S/C=1 and S/C=1.7 reaction conditions. The LSCN-0.5 catalyst exhibited the best performance under Ni-substitution of which propane conversion and hydrogen yield was 100%, 95.9% at $800^{\circ}C$ in the S/C=1.7 condition, respectively. The morphology of carbon deposited on the catalysts after reaction exhibited filamentous carbon and amount of carbon deposited on the catalysts after reaction increased with an increase in the amount of added Ni.