• Korean Chemical Engineering Research
• /
• 제51권4호
• /
• pp.455-459
• /
• 2013

휴대용 연료전지 시스템에 사용되는 연료 개질 시스템은 수소 발생기, 산화기, 일산화탄소 제거기로 구성되어 있다. 휴대용 연료전지 시스템 설계에서 시스템의 기동 시간은 매우 중요한 설계 인자이다. 특히, WGS 반응기의 기동 시간은 리포메이트의 질을 결정하기 때문에 전체 시스템의 기동 시간에 중요한 부분을 차지한다. 본 논문에서는 과량의 일산화탄소가 포함되어 있는 리포메이트 가스를 WGS 반응기에서 산화시킴으로써 WGS 반응기를 가열하는 방법을 사용하였다. 이때 공급되는 공기는 WGS 반응기 입구에 공급되어 기동 초기에 발생되는 과량의 일산화탄소가 함유된 리포메이트 가스를 제거하므로써, 운전 중에 일산화탄소의 과잉 공급없이 안정적으로 리포메이트를 공급함으로써 기동 시간을 단축할 수 있었다.

• Korean Chemical Engineering Research
• /
• 제62권3호
• /
• pp.238-245
• /
• 2024

젖산 전극은 환자의 건강상태와 스트레스 수준, 및 운동선수의 피로도를 실시간으로 모니터링하는 젖산 센서 또는 젖산 연료전지 전극으로 활용될 수 있다. 본 연구에서는 젖산 산화효소, 카탈라아제, 미토콘드리아로 구성된 고성능 전극을 제작하고 전극의 표면분석 및 전기화학적 특성을 조사하였다. 단일벽 탄소나노튜브로 개질된 탄소종이(CPSWCNT)는 개질 전보다 전기 전도성이 크게 향상되었다. 젖산 산화효소, 카탈라아제, 그리고 미토콘드리아가 부착된 전극(CP-SWCNT-LOx-Cat-Mito)은 젖산 산화효소와 카탈라아제가 부착된 전극에 비하여 많은 전류를 생산하였다. 빌리루빈 산화효소(BOD)가 부착된 전극(CP-SWCNT-BOD)이 생산하는 환원전류량은 전해질의 산소 존재 유무에 따라 크게 영향을 받았다. CP-SWCNT-LOx-Cat-Mito (anode)와 CP-SWCNT-BOD (cathode)로 구성된 연료전지는 133 ㎂/cm²로 방전 시 0.2 V의 셀 전위를 유지하며 29 ㎼/cm²의 전력을 생산하였다. 본 연구결과는 미토콘드리아가 젖산 센서 및 연료전지 성능 향상에 필수적인 생체물질임을 시사한다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.260-265
• /
• 2006

An experimental study on the catalytic reformer adopted in the auxiliary power unit system of solid oxide fuel cell was conducted. A 3-fluid nozzle, by which liquid fuel such as diesel, water and air are sprayed and uniformed mixed, was designed and used in this study. An electrically heated monolith inserted in the reformer was used for the vaporization of fuel and water in the transient state of reformer. The reformer uses the partial oxidizing reaction at the catalyst and the supply of water prevents the flame combustion in the spraying zone and lessens the deactivation of catalyst. The result showed that the reforming of liquid fuel can be started by the electrically heated monolith and the 3-fluid nozzle can give the uniform mixing of fuel, water and air. It was also found that the reformer fueled by n-hexadecane can make the reformate, at best, containing $H_2$ at 15.5% and CO at 11.5% that are used as fuel in the solid oxide fuel cell.

• 공업화학
• /
• 제19권1호
• /
• pp.31-36
• /
• 2008

혐기성소화가스(ADG)를 원료로 수소를 제조하여 연료전지에 활용할 경우 ADG에 포함된 황화합물이 개질기의 촉매와 연료전지의 전극에 독으로 작용하므로 금속이온이 담지된 활성탄을 이용하여 황화합물을 제거하였다. 수분과 산소농도에 따라 고정층 흡착량이 변화하였으며, 산소 0.2 vol%, RH 90% 이상일 때 가장 높은 흡착량을 나타내었다. 본 연구에서는 KI 첨착한 활성탄에서 황화합물의 흡착특성을 고정층에서 동특성 실험을 통해 관찰하고 그 결과를 기준으로 흡착탑을 설계 제작 현장실험을 실시하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.243-247
• /
• 2005

This paper describes an on-going national R&D program for the development of a gas turbine/fuel cell hybrid power generation system and related R&D activities. The final goal of this program is to develop a 200kW-c1ass gas turbine/fuel cell hybrid power generation system and achieve high efficiency over $60\%$ (AC/LHV). In the first phase of the development, a sub-scaled 60kW-class hybrid system based on the 50kW-class microturbine and the 5kW SOFC will be developed for the purpose of concept proof of the hybrid system. Core components such as the microturbine and the SOFC system are being developed and parallel preparation for system integration is being carried out. Before the core components are assembled in the final system. operating characteristics of a hybrid system are investigated from a simulated system where a turbocharger (microturbine simulator) and a modified fuel cell burner test facility (fuel cell simulator) are employed. The 60kW demonstration unit will be built up and operated to provide the valuable information for the preparation of the final full scale 200kW hybrid system.

• 한국가스학회지
• /
• 제11권1호
• /
• pp.51-54
• /
• 2007

78개 셀의 전극유효 면적이 $295cm^{2}$인 고분자 전해질 연료전지(PEMFC) 스택의 운전특성과 CO 피독에 대한 영향을 조사하였다. 전류밀도 $325mA/cm^{2}$에서 출력 5.4kW를 6시간 유지시키는 동안 셀들의 전압편차는 2.3%로 매우 안정함을 보였다. 개질과정의 부산물로 생성되는 CO는 PEHFC의 성능에 중요한 영향을 끼치는 스택의 주 오염물질중의 하나이다. 시간에 따른 연속적인 CO 피독 실험(5-20ppm)은 스택의 피독과 재생과정의 route를 알 수 있었다.

• 대한기계학회논문집B
• /
• 제29권6호
• /
• pp.722-729
• /
• 2005

Design analysis of the solid oxide fuel cell and gas turbine combined power system is performed considering different methods for preheating cell inlet air. The purpose of air preheating is to keep the temperature difference between cell inlet and outlet within a practical design range thus to reduce thermal stress inside the cell. Three different methods considered are (1) adopting a burner in front of the cell, (2) adopting a preheater (heat transfer from the main combustor) in front of the cell and (3) using recirculation of the cathode exit gas. For each configuration, analyses are carried out for two values of allowable maximum cell temperature difference. Performance characteristics of all cases are compared and design limitations are discussed. Relaxation of the cell temperature difference (larger difference) is proved to ensure higher efficiency. Recirculation of the cathode exit gas exhibits better performance than other methods and this advantage becomes more prominent as the constraint of the cell temperature difference becomes more severe (smaller temperature difference).

• 대한기계학회논문집B
• /
• 제32권11호
• /
• pp.849-855
• /
• 2008

The paper addresses modeling and analysis of the part load performance of a hybrid fuel cell system integrating a polymer electrolyte membrane fuel cell(PEMFC) and a gas turbine(GT). The system is a pressurized one where the working pressure of the PEMFC is higher than the ambient pressure. In addition to the two major components, the system also includes auxiliary parts such as a steam reformer, a humidifier, and afterburner and so on. Based on design analysis, component off-design models are incorporated in the analysis program and part load operation is simulated. The mode for the part load operation of the PEMFC/GT hybrid system is a variable rotational speed operation. The operating characteristics and variations in the system efficiency and component performance parameters at part load are analyzed.

• 한국군사과학기술학회지
• /
• 제14권4호
• /
• pp.732-739
• /
• 2011

A fuel cell/secondary battery hybrid power generation system could extend well beyond the efficiency and interoperability of the conventional diesel generator. The suggested power source system consists of 2.3 kW class PEMFC, 100 Ah lithium polymer battery, and two DC/DC converters by serial connection type. It was known that interoperability of sub-systems is the key factor for stable and optimal control of the hybrid power generation system. The modeling and simulation methods have been proposed to reduce the number of configurations and performance tests for components selection and select the optimized control condition of the power generation system. The control model for power source system is implemented based on the empirical formulation and carried out in the Matlab/Simulink environment. The results show that the simulation can be used to establish the algorism of prototype and increase the durability of the power source system.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.21-24
• /
• 2008

We have developed a $kW_e$ class liquid fuel based solid oxide fuel cell (SOFC) system. Our final target is to develop the 1 $kW_e$ diesel based SOFC system for residential power generator(RPG). In this study, we present the conceptual design of SOFC system. System is composed of hot-box and cold-box. Planar typed SOFC stack, heat exchanger, combustor for stack tail gas, and fuel processor, such as fuel reformer and desulfurizer, are contained in the hot-box. And several balance of plants(BOP), such as fuel suppliers and controller, are contained in the cold-box. Before the SOFC system fabrication, we have already operated the selfsustaining fuel processor, and heat exchange of all heat-related components is simulated using ASPEN HYSYS, because heat maintenance and management in hot-box are important for stable operation of SOFC system. The self-sustained fuel processor was successfully operated for about 250 hours, and heat exchange is enough to operate the SOFC system.