• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.446-450
• /
• 1991

PID controller is popular but have defect inversing following reference input and noise elimination. Therefor, this paper focus on reducing rise time and robustness against noise. The result that is simulated with feedforward method and sliding mode show that rise time decrease and robustness increase.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.11
• /
• pp.720-726
• /
• 1988

This paper deals with an applicaton of some adaptive algorithms to a heat exchanger using a microcomputer and reviews the experimental results obtained. The heat exchanger prepared for experments was identified as a non-minimum phase system and its exact mathematical models was hardly obtainable with direct computation. Thus, classical strategies, such as PID, needed many trial and errors to determine parameters of the controllers. Furthermore such strategies could not guarantee good performance when system parameters vary. To overcome these difficulties and improve performance, two adaptive methods applicable to a non-minimum phase system were chosen and put to the test. In this paper the performance of adaptive controllers is compared with that of conventional PID controller. The final objective of this paper is to construct a controller readily applicable to industrial processes using a microprocessor.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.211-220
• /
• 2014

In this paper a full FPGA-based and compact motor-control system is shown that makes it easy to control the motor and analyze the result data in real time with embedding not only a DC motor controller but also a TFT LCD interface in a single FPGA. Both a PID speed control module for a DC motor and a monitoring module for plotting real time graphs on to a TFT LCD are designed in a single FPGA, and the system validity is shown through simulation and experimental results. The FPGA used is xc3s400 and the entire system is designed by using the AD (Altium Designer). A PWM motor drive system is constructed by using MOSFETs for a DC motor 4-quadrant operations.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1735_1736
• /
• 2009

This paper discusses about a robust servo system applying PID control to PMSM. The system has robustness by Sliding Mode Controller. A novel sliding surface is defined by virtual state. This sliding surface has nominal dynamics of an original PID control system. So Sliding Mode Control(SMC) technique can be used with PID controller. Its design is based on the augmented system whose dynamics have a higher order than that of the original system. The reaching phase is removed by using an initial virtual state whitch makes the initial sliding function equal to zero.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.1
• /
• pp.78-84
• /
• 1998

The fluid system such as, the quantity control of raw water, chemicals control in the purification, the waste water system as well as in the feed water or circulation system of the power plant and the ventilation system is controlled with the valve and moter pump. The system's performance and the energy saving of the fluid systems depend on control of method and delicacy. Until, PI controller use in these system but it cannot control delicately because of the coupling in the system loop. In this paper we configure a single flow system to the multi variable system and suggest the application of 2-DOF PID controller and the tuning methods by the neural network to the electrical power of the flow control system. the 2-DOF controller follows to a setpoint has a robustness against the disturbance in the results of simulation. Keywords Title, Intelligent control, Neuro control, Flow control, 2 - DOF control., 2 - DOF control.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.3
• /
• pp.114-119
• /
• 2001

An automatic train operation(ATO) system executes the operation of constant speed travelling and fixed point parking by using microprocessors instead of driver's manual operation. This paper describes the mathematical model for the train considering unknown disturbances which consist of start resistance, travelling resistance, slope resistance, curve resistance, and so on. The speed controller of ATO system is designed by considering the disturbances. The simulation is executed to verify the speed control and fixed point parking performance and to compare its performance with that of a PID-type ATO control system under disturbances. Simulation results show that the control performance of gain scheduled control scheme for ATO system is better than that of the conventional PID controller.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.112-115
• /
• 2003

Robust control for servo control system in needed according to the highest precision of industrial automation. However, when a servo control system has an effect of disturbance, it is very difficult to guarantee the robustness of control system. As a compensation method solving this problem in this paper, Hybrid control method of Main controller(PIU)-Differential Supervisory controller is presented. Main controller is operated as a feedback controller. Differential Supervisory controller as a assistant controller is operated when state in unstable disturbance. The robust control function of Differential Supervisory controller is demonstrated by Speed control of Motor.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.5
• /
• pp.131-138
• /
• 1996

This paper suggests a servo control algorithm to reduce the repeatable tracking error which is not explicitly taken into account in the design of a conventional PID controller of a computer hard disk drive. The robust stability of the repetitive control system with multiplicative modelling error is analyzed, and the controller was implemented using a fixed point DSP(Digital Signal Processor). Experimental results show that the repetitive errors are suppressed effectively by the proposed controller.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.370-373
• /
• 2010

본 논문에서는 유도전동기와 제어기의 폐루프 극점을 원하는 위치에 배치하여 유도전동기를 위한 PID제어 동조파라미터를 얻어 유도전동기를 제어하는 방법을 제안한다. 이러한 설계방법은, 설계요건뿐만 아니라 제어기 고유의 안정도와 강인성까지 제공하므로 매우 유용하다.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.9
• /
• pp.646-654
• /
• 1988

In this paper, a speed controller using a microcomputer is implemented and applied to a DC Servo Motor. Adaptive control is applied to a system for which a priori knowledge to its mathematical model is insufficient, on the basis of input and output data an apropriate controller is constructed through which the system input is synthesized. The pole-placement PID self tuning control algorithms as a control algorithm is used to compare the performance of the controller with that of the classical PID controller through computer simulations and experiments.