• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.2
• /
• pp.93-101
• /
• 2001

본 논문은 국내의 비보강 조적조에 대해 내진성능을 조사하기 위하여 재료측성 평가를 위한 실험연구를 수행하였다. 실험결과를 바탕으로 조적용 모르터의 압축강도식을 제안하였다. 또한 조적용 모르터의 배합비에 따른 조적조 프리즘의 압축강도 특성을 비교하였다. 조적조 프리즘의 압축강도로써 조적조의 탄성계수를 구할 수 있는 약산식을 제시하였으며, 약산식을 사인장 조적조 실험을 통하여 구한 전단탄성계수값과 비교하여 볼 때 타당성을 가지고 있다고 판단된다. 실험결과로써 나온 재료특성 값을 바탕으로 2층 조적조 다세대 주택에 대한 유사동적해석을 수행하였다. 해석결과로 얻은 전단응력과 전단파괴가 나타난 사인장 조적조의 허용전단응력은 유사한 것으로 확인되었다.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.5
• /
• pp.107-116
• /
• 2000

강우에 의한 얕은 사면파괴는 우리 나라에서 흔히 볼수 있는 사면파괴의 형태이다. 본 연구에서는 재현기간에 따른 강우강도와 지속시간을 고려한 한계평형법에 의하여 이러한 얕은 사면파괴의 가능성을 평가하기 위함 방법에 대하여 논의하였다. 이를 위해 일차원 침투모델인 Green-Ampt 모델에 바탕을 둔 두 방법을 고려하였다. 즉 침투능에 따른 침투깊이를 산정하는 Pradel과 Raad의 방법과 일정한(uniform) 강우강도가 작용할 경우 폰딩(ponding)에 대해 해를 주는 Mein과 Larson의 방법을 고려하여 함수특성이 알려진 화강풍화토사면에 적용하였다. 연구결과에 의하며 Pradel과 Raad 방법은 실제 적용된 강우강도가 아닌 침투능을 바탕으로 침투깊이를 산정하므로 Mein과 Larson 방법에 비해 보수적인 사면안정 해석결과를 예측한다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.95-104
• /
• 2002

A methods to calculate non-linear moment-curvature relations of high-strength PSC flexural members for numerical analysis has been proposed. The moment-curvature relations were calculated with assumptions of design codes and by the layer method. The results of the proposed procedures for moment-curvature relations and numerical analysis were compared with those of pre-existing tests. The absorption energy rate of the design codes was about 30% larger than that of the layer method. The ultimate load and the external work of the layer method were 90% and 85% of those of tests, respectively The ultimate load of the strength design method was 97% of that of tests, but the external work was over-estimated with 122%. The ultimate load and external work by the proposed equation of the CEB-FIP Model Code were 113% and 173% of those of tests, respectively. It show that the use of ultimate strain of 0.0035 should be over-estimated for high-strength concrete. The procedure of non-linear numerical analysis of this research could be stably simulated the behavior of concrete flexural members until the ultimate state, and calculate results of the load-deflection relation and cracking pattern were very similar with those of tests.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.135-143
• /
• 2001

강우에 의한 잔류토에서의 얕은 사면파괴는 세계적으로 흔히 볼 수 있는 사면파괴의 형태이다. 본 연구에서는 침투가 사면 표면의 안정에 미치는 영향을 평가하기 위해 한계평형법을 이용하는 무한사면 해석법을 연구하였다. 재현기간에 따른 강우강도가 지속기간이 고려되는 임의의 강우에 의해 유발되는 얕은 사면파괴의 가능성을 평가하기 위해서 Green-Ampt 모델에 바탕을 둔 간략법들이 적용되었다. 간략법들에 의한 결과들과 비교하기 위하여 일련의 수치해석이 수행되었다. 그 결과에 의하면 적절하게 선택된 입력값을 사용하면 수정간략법이 더욱 엄밀한 해석법인 유한요소해석과 근사한 합리적인 결과를 줌을 알 수 있다.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.5
• /
• pp.5-19
• /
• 2019

Considering the natural phenomenon in which steep slopes ($65^{\circ}{\sim}85^{\circ}$) consisting of rock mass remain stable for decades, slopes steeper than 1:0.5 (the standard of slope angle for blast rock) may be applied in geotechnical conditions which are similar to those above at the design and initial construction stages. In the process of analysing the stability of a good to fair continuum rock slope that can be designed as a steep slope, a general method of estimating rock mass strength properties from design practice perspective was required. Practical and genealized engineering methods of determining the properties of a rock mass are important for a good continuum rock slope that can be designed as a steep slope. The Genealized Hoek-Brown (H-B) failure criterion and GSI (Geological Strength Index), which were revised and supplemented by Hoek et al. (2002), were assessed as rock mass characterization systems fully taking into account the effects of discontinuities, and were widely utilized as a method for calculating equivalent Mohr-Coulomb shear strength (balancing the areas) according to stress changes. The concept of calculating equivalent M-C shear strength according to the change of confining stress range was proposed, and on a slope, the equivalent shear strength changes sensitively with changes in the maximum confining stress (${{\sigma}^{\prime}}_{3max}$ or normal stress), making it difficult to use it in practical design. In this study, the method of estimating the strength properties (an iso-angle division method) that can be applied universally within the maximum confining stress range for a good to fair continuum rock mass slope is proposed by applying the H-B failure criterion. In order to assess the validity and applicability of the proposed method of estimating the shear strength (A), the rock slope, which is a study object, was selected as the type of rock (igneous, metamorphic, sedimentary) on the steep slope near the existing working design site. It is compared and analyzed with the equivalent M-C shear strength (balancing the areas) proposed by Hoek. The equivalent M-C shear strength of the balancing the areas method and iso-angle division method was estimated using the RocLab program (geotechnical properties calculation software based on the H-B failure criterion (2002)) by using the basic data of the laboratory rock triaxial compression test at the existing working design site and the face mapping of discontinuities on the rock slope of study area. The calculated equivalent M-C shear strength of the balancing the areas method was interlinked to show very large or small cohesion and internal friction angles (generally, greater than $45^{\circ}$). The equivalent M-C shear strength of the iso-angle division is in-between the equivalent M-C shear properties of the balancing the areas, and the internal friction angles show a range of $30^{\circ}$ to $42^{\circ}$. We compared and analyzed the shear strength (A) of the iso-angle division method at the study area with the shear strength (B) of the existing working design site with similar or the same grade RMR each other. The application of the proposed iso-angle division method was indirectly evaluated through the results of the stability analysis (limit equilibrium analysis and finite element analysis) applied with these the strength properties. The difference between A and B of the shear strength is about 10%. LEM results (in wet condition) showed that Fs (A) = 14.08~58.22 (average 32.9) and Fs (B) = 18.39~60.04 (average 32.2), which were similar in accordance with the same rock types. As a result of FEM, displacement (A) = 0.13~0.65 mm (average 0.27 mm) and displacement (B) = 0.14~1.07 mm (average 0.37 mm). Using the GSI and Hoek-Brown failure criterion, the significant result could be identified in the application evaluation. Therefore, the strength properties of rock mass estimated by the iso-angle division method could be applied with practical shear strength.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.153-161
• /
• 2005

A series of installation damage tests and creep tests are performed to assess the combined effect of installation damage and creep deformation far the long-term design strength of geogrid reinforcement. Three types of geogrids are used to investigate the influence of the geogrid types. From the experimental results, it is shown that installation damage and creep deformation of geogrids significantly depends on the polymer types of the geogrids and the larger the installation damage, the more the combined effect of installation damage and creep deformation. In addition, The results of this study show that the tensile strength reduction factor, RF, considering the combined effect between installation damage and creep deformation is less than that calculated by the current design practice which calculates the long-term design strength of geogrids damaged during installation by multiplying two partial safety factors, $RF_{ID}$ and $RF_{CR}$.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.108-108
• /
• 2012

이전의 연구에서 기존의 ATY 장치에 ITY 노즐을 접목하여 개조한 사가공기로 제조한 탄성복합사를 자동차 시트용 트리코트 원단으로 편직하여 일광견뢰도가 우수한 염료를 선정하고 $125^{\circ}C$에서 염색하여야 견뢰도와 spandex의 물성을 저해하지 않음을 알 수 있었다. 폴리에스테르 탄성복합사의 염색성 평가에 이어 본 연구에서는 나일론 필라멘트 (70/24, Full-dull, 2ply사와 40D spandex 1ply사 복합)와 레이온사(75D, 1ply)를 투입하여 직물 원단(중량 216g/yd, 밀도 경사 78, 위사 52본/inch)을 제직한 후 2욕에서의 염색공정을 거칠 경우, 탄성복합사의 견뢰도와 물성에 미치는 영향을 조사하였다. 나일론, 레이온, 폴리우레탄의 3종 원단을 염색성 평가를 위하여 반응성염료로 먼저 레이온 부분을 염색한 후 산성염료로 나일론 부분을 염색하였으며, 이 때 spandex가 미치는 영향을 비교하기 위하여 spandex가 함유되지 않은 나일론, 레이온 복합 제직원단도 함께 염색한 후 견뢰도를 평가하였다. 또한, 레이온 부분은 CPB염색법과 제트염색기로 나누어 염색하여 염색기에 따른 인장강도와 인열강도를 평가하였다. 레이온 염색에는 셀룰로오스용 2관능기 반응성염료 3원색을 이용하여 khaki color로 combination염색하였으며, 나일론 부분에는 입자크기가 커서 견뢰도가 우수한 산성염료를 선정하여 combination염색한 후 냉수세하였다. 견뢰도를 비교한 결과, spandex가 포함된 탄성복합사 원단과 나일론과 레이온 만으로 제직된 원단 모두 세탁, 마찰, 물, 땀, 일광 견뢰도 모두가 4~5급으로 우수하여 spandex에 이염된 염료가 견뢰도에 미치는 영향은 없음을 확인하였다. 또한, 레이온 부분의 반응성염료 염색 시 CPB와 제트염색법의 두 가지 종류에 대한 인장강도와 인열강도 평가결과는 CPB 염색물이 제트염색물보다 약간 높게 나타났지만 3% 이내의 차이로 거의 차이가 없음을 나타내었다. 일반적으로 제트염색 시 원단은 로프상으로 이동하고, CPB염법은 확포상태 그대로 염색되기 때문에 제트염색 시 강도가 낮아지는 것으로 알려져 있으나, 본 연구에서는 탄성복합사를 경사, 위사 모두 사용함으로써 spandex가 신장하는 특성 때문에 강도의 저하가 없는 것으로 사료된다.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.05a
• /
• pp.141-146
• /
• 2005

Ship have cutout inner bottom and girder and floor etc. Ship's structure is used much, and structure strength must be situated, but establish new concept when high stress interacts sometimes fatally the area. There is no big problem usually by aim of weight reduction, a person and change of freight, piping etc. Because cutout's existence grow up in this place, and, elastic buckling strength by load causes large effect in ultimate strength. Therefore, stiffened perforated plate considering buckling strength and ultimate strength is one of important design criteria which must examine when decide structural concept at initial design. Therefore, and, reasonable buckling strength about perforated stiffened plate need to ultimate strength limited design . Calculated ultimate strength varied several web height and cutout's dimension, and thickness in this investigated data. Used program(ANSYS) applied F.E.A code based on finite element method.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.6
• /
• pp.13-19
• /
• 2013

In this study, the target ground was selected for the assessment of liquefaction, for which energy-based Arias intensity liquefaction assessment method was applied, The results of evaluation by simplified method using conventional in-situ test were compared. The result of the assessment of liquefaction revealed that the safety factor of the Arias Intensity using the actual records of the Hachinohe and Ofunato earthquake showed generally similar trends with the simplified method, However, the Arias Intensity factor of safety for the artificial earthquake created from the design response spectrum showed some difference from the factors of safety of the simplified method. The shear stress ratio and the occurrence strength of the Arias Intensity are differently calculated between stress and energy, but the resistance stress ratio of the simplified method and the resistance strength of the Arias Intensity use the empirical chart of the results of the standard penetration test for the actual liquefaction areas by the earthquake, which seems the reason for the similar results between Arias Intensity assessment and stress concept simplified method for Hachinohe and Ofunato earthquakes. Therefore, it was found that the energy-based Arias Intensity liquefaction assessment could represent the dynamic changes of the ground caused by seismic characteristics such as acceleration, magnitude, duration and amplitude.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.2
• /
• pp.130-137
• /
• 2017

Due to the economic growth and development of construction technology, a role of foundation to resist heavy loads has been increased. In this present study to improve the structural performance of reinforced concrete pile, the precast HPC pile reinforced with rebar and filling concrete was developed and the strength of pile was predicted based on the limit state design method. The safety of HPC pile strength was evaluated by comparing with the design values. The geometry of HPC pile is a decagon cross section with a maximum width of 500 mm and a minimum width of 475 mm, and the hollow head of pile thickness is 70 mm. The inner area of the hollow head part was made as the square ribbed shape presented in the limit state design code in order to achieve horizontal shear strength between pile concrete and filling concrete. From the shear test results, it was found that the stable shear strength were secured without abrupt failure until maximum load stage despite the shear cracks was found. Shear strength is 135% and 119% higher than that of design value calculated from limit state design code. The driving test results of HPC pile according to the presence of additional reinforcement showed the outstanding crack resistance against impact loads condition. From the bending test results the flexural load between PHC pile and HPC pile was 1.51 times and 1.48 times higher than that of the design flexural load of conventional PHC pile.