• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.2
• /
• pp.91-96
• /
• 2010

The purpose of this study is to find problems about pedestrian road of tourist resort and to make new type of sidewalk pavement with wood chip and binder using urethane resin on the parks and tourist resort. The wood chip pavement has new economics and durability with comfortable texture. Samples of these pavement materials were tested for tensile strength, permeability and ball rebound value. Also, after immersion for 24 hours, tensile strength, samples' thickness and weight were measured and discussed the strength reduction according to the water immersion. Tensile strength experimentation was examined on dry condition and water immersion. The result of examination on dry condition was 1.06MPa and on water immersion was 0.67MPa. The results showed 36.8% decreasing rate of tensile strength. Permeability experiment test based on field permeability method of pavement were conducted as a result, permeability coefficients were in the range of 0.67~0.78mm/s that all exceeds object permeability coefficient. Elasticity experiment was based on elasticity test method of Japan road association. GB coefficient was 21% and SB coefficient was 10%. GB coefficient and SB coefficient increased if fine aggregate were increased.

• Economic and Environmental Geology
• /
• v.42 no.4
• /
• pp.357-366
• /
• 2009

Since weathering weakens the rock fabric and exaggerates any structural weakness, it affects mechanical properties as well as physical and chemical properties of rock. Weathering leads to a decrease in density, strength, friction angle and cohesion, and subsequently it affects negatively on the stability of rock slope. The purpose of the study is to investigate the changes of the rock slope stability caused by discontinuities which have different weathering grades. For that, the discontinuity samples which are divided into two different weathering grades are obtained from the field and tested their mechanical properties such as JCS, JRC and residual friction angle. In order to evaluate the effects on the stability of slope due to weathering, the deterministic analysis is carried out. That is, the factors of safety for planar failure are calculated for rock masses which have two different weathering grades, such as fresh and weathered rock mass. However, since the JRC and friction angle values are widely scattered and the deterministic analysis cannot consider the variation, the factors of safety cannot represent properly the stability of the rock slope. Therefore, the probabilistic analysis has been used to consider the scattered values. In the deterministic analysis, the factors of safety for the fresh discontinuity and weathered discontinuity are 1.25 and 1.0, respectively. The results indicate the fresh discontinuities are stable for planar failure and the weathered discontinuities are marginally stable. However, the probabilities of failure for the fresh discontinuity and weathered discontinuity are 25.6% and 45.9%, respectively. This shows that both discontinuities are analyzed as unstable in the probabilistic analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.10
• /
• pp.2810-2818
• /
• 2009

In order to examine the characteristic of shallow failure in cut slopes composed of weathered granite soil, this study calculated critical permeability coefficient according to rainfall characteristic in Korea, performed stability analysis according to the representative physical properties of weathered granite soil distributed in Korea such as horizontal distance to the failure surface of cut slope, slope inclination, slope height, and the depth of wetting by rainfall, and analyzed the results. In the results of analyzing critical permeability coefficient, when the local rainfall characteristic was considered, the maximum critical permeability coefficient was $7.16{\times}10^{-4}cm/sec$. We judged that shallow failure according to wetting depth should be considered when rainfall below the critical rainfall intensity lasts longer than the minimum rainfall duration in cut slopes composed of weathered granite soil, which had a critical permeability coefficient lower than the maximum critical permeability coefficient. Furthermore, using simulated failure surface, this study could understand the characteristic of shallow failure in cut slopes based on the change in slope safety factor according to horizontal distance, wetting depth, and strength parameter.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1991-1995
• /
• 2010

도시화로 인한 토지 피복 상태의 변화로 인한 불투수면적의 증가와 강우강도가 증가함에 따라 지하수로 침투하지 못하고, 바다로 유출되는 강우량이 점차 증가하고 있다. 또한, 인구의 증가와 산업발달에 따른 무분별한 지하수의 사용은 심각한 지하수위의 하강으로 이어지고 있다. 지하수위와 강우량간의 상관관계를 분석하여 지하수의 체계적인 관리 및 운용을 하고자 본 연구를 진행하였다. 본 연구에서는 경상도 지역의 지하수위 관측소와 강우 관측소간의 거리가 10km 이내인 지점을 선정하여, 관측 자료와 분석결과를 토대로 13개 지점을 선정하였다. 침투현상이 침루과정을 거쳐 지하수에 유입되는 과정을 고려하면 강우가 발생한 시점보다 시간이 경과 한 후에 이 지점의 하루에 내린 강우량이 이틀에 걸쳐 지하수위에 영향을 준다고 가정하였고, 1일째의 강우를 실제 강우량의 최대 100%에서 50%까지로 설정하고 2일째에 나머지 강우가 내렸다고 가정하여 각각의 강우이동평균값과 지하수위간의 상관관계를 분석하였다. 또한, 한계침투량을 고려하여 강우이동평균값과 지하수위간의 상관관계를 분석하였다. 그 결과 한계침투량 고려시 상관계수가 0.5 이상인 지점들 중 약 70%가 강우량을 강우사상이 발생한 당일과 명일로 나누었을 때, 상관계수가 높게 나타났다. 그러므로 기존 강우와 지하수위 관측자료만 이용하여 강우이동평균과 지하수위의 상관관계를 분석하는 것 보다 침투율을 고려한 강우이동평균과 지하수위의 상관관계 분석으로 인해 지하수의 체계적인 관리와 분석이 가능할 것으로 사료된다.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.584-595
• /
• 2018

This study conducted direct shear test on about 290 sorts of materials such as sandy soil, clayey soil and gravely soil to present proper standard on shear strength of soil. Shear strength of soil in large scale tends to show that angle of internal friction increases as sand contents grow and it ranges $23.5^{\circ}{\sim}34.9^{\circ}C$ with cohesion of 2.0 kPa~15.7 kPa. Elastic modulus was visibly distinct by load, and which increased approximately 80% as vertical load grows. Angle of internal friction arranging $15.0^{\circ}{\sim}28.6^{\circ}$ on clayey soil decreased as clay contents rises and cohesion increase in regular scale. Elastic modulus tends to increase initial elastic modulus with almost same growing rate. While angle of internal friction on gravely soil indicates $29.9^{\circ}{\sim}36.7^{\circ}$ which hardly shows distinctive features. According to test in detail, cohesion of SW (well-graded sand), SP (poorly-graded sand), SC (clayey sand) and SM (silty sand) indicates value by 94%, 78% and 59% comparing to SC, SW and SP respectively. Angle of internal friction of ML (low-liquid limit silt) and CL (low-liquid limit clay) appears almost same features, and MH (high-liquid limit silt) despite of 88% value of ML. Cohesion among them varies with similar growing rate.

• Geotechnical Engineering
• /
• v.12 no.1
• /
• pp.21-34
• /
• 1996

This paper presents the engineering characteristics of the Samcheok organic soil which contains a large portion of organic matter and high natural water content. A series of lab tests shows that the measured liquid limit is quite different depending on preparing methods of specimens. The values tested with natural condition are higher up to 4 times than thole of the oven dry specimen. It is shown that the organic soils fail at large strain and do not show peak stress in the stress strain relationships. Also strength increase ratios, which are measured 0.43 to 0.65 in this tests, are significantly higher than those of the soft clay without organic matter. The consolidation tests indicate that the verti'cal and horizontal Permeabilities are almost the same. For the remolded samples is reduced from 112 to 116 of the vertical permeability An increase of organic matter or water content of the organic soils results in an increase of the coefficient of secondary consolidation. The increase rate is slow below 15 percents of the organic contents while the rate becomes higher above the value.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.24-29
• /
• 2018

The properties of concrete with addition of microgel - containing hydrogel support were investigated. As a result of measuring the slump of the self - healing concrete, the target slump was satisfied in all the mixing conditions, but the slump was decreased as the mixing amount of the hydrogel support increased. The change of porosity due to incorporation of hydrogel support was minimal. As a result of the evaluation of the compressive strength of the self - healing concrete, the incorporation of the hydrogel support did not affect the strength. However, under the same mixing condition, the dispersion value of the specimens tended to increase with increasing hydrogel support contents. As a result of the permeability test of self-healing concrete according to the incorporation of hydrogel support, it was confirmed that the mixing ratio of hydrogel support was effective to decrease the permeability coefficient.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.5
• /
• pp.155-163
• /
• 1995

The primary purpose of this study is to hvestigate reusal techniques of high calclun-i fly ash in the construct.ion field, which may contribute to the savings of construction materials and consenratlng environment. Furt.hcrrnore, it can setup material properties or characteristics requiremi for development of new materials. Firstly, chemical and physical cahraci.eristics of liigh~calciurn fly ash is arialyseti. And then, the usability of the concrete is tcsted by investigating the flowablility and strength development through parameters of various replace ment r,itios with respect to different nuxing conditions. Finally, the durability and mechanical properties(e1astic nlodulus of the concrete is tested. As the result of the study, the following conclusions are derived : (1) the quaritii y of the CaO The primary purpose of this study is to hvestigate reusal techniques of high calclun-i fly ash in the co:lstruct.ion field, which may contribute to the savings of construction materials and consenratlng environment. Furt.hcrrnore, it can setup material properties or characteristics requiremi for development of new materials. Firstly, chemical and physical cahraci.eristics of liigh~calciurn fly ash is arialyseti. And then, the usability of the concrete is tcsted by investigating the flowablility and strength development through parameters of various replace ment r,itios with respect to different nuxing conditions. Finally, the durability and mechanical properties(e1astic nlodulus of the concrete is tested. As the result of the study, the following conclusions are derived : (1) the quaritii y of the CaO

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.613-620
• /
• 2013

Concrete has been recognized as a material which is resistant to high temperatures, but chemicophysical property of concrete is changed by the high temperature. So, mechanical properties of concrete may be reduced. Because of this, standards and researches on the degradation of the mechanical properties of concrete at high temperatures have been presented. However, research data about the state that considering the loading condition and high-strength concrete is not much. Therefore, this study evaluated the high-temperature properties of high-strength concrete by loading condition and elevated temperature. The stress-strain, strain at peak stress, compressive strength, elastic modulus, thermal strain and the transient creep are evaluated under the non-loading and $0.25f_{cu}$ loading conditions on high strength concrete of W/B 12.5%, 14.5% and 20%. Result of the experiment, decrease in compressive strength due to high temperature becomes larger as the compressive strength increases, and residual rate of elastic modulus and compressive strength is high by the shrinkage caused by loading and thermal expansion due to high temperature are offset from each other, at a temperature above $500^{\circ}C$.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.193-197
• /
• 2001

본 연구에서는 국산닥, 태국닥, 중국닥의 원료를 사용하여 펄핑, 표백, 고해, 초지, 건조의 방식을 변화시켜 총 3500 여장에 이르는 한지를 한지제조 전문가가 일정한 방법에 따라 제 조하였고 그 특정들을 조직적으로 검토하였다. 이러한 연구는 한지의 물성이 닥섬유의 처 리공정에 의해 어떻게 영향을 받는지 연구를 통계적으로 가능하게 하였다. 본 연구에서는 육재펄핑과 일광표백의 효과, 외발뜨기와 쌍발뜨기의 효과, 고해방식의 차이, 먹퍼집성에 대 해 결과들을 보이 고 있다. 육재 펄핑과 일광표백이 한지의 물성에 어떠한 영향을 미치는지 알아보기로 하였다. 현 재는 많은 한지 업자들이 육재펄핑보다는 가성소다 펄핑 (그림에서는 약품펄핑으로 표기), 일광표백보다는 차아염소산 나트륨 (그림에서는 약품표백으로 표기)을 사용하는 것이 보통 이다. 육재펄핑과 일광표백을 실시한 한지는 열단장, 인열강도, 내절도를 약품펄핑이나 약 품표백보다 높이는 효과가 있음을 알 수 있었다. 하지만 약품을 사용하는 경우 리그닌의 용출이 더 수윌하므로 백색도는 약품을 사용하는 경우가 더 유리하였다. 국산닥의 경우 육 재펄핑과 일광표백을 한 경우 먹퍼짐성이 약품사용 한지보다 크지 않음을 볼 수 있었다. 한국의 전통적인 외발뜨기 초지방식은 일본의 쌍발뜨기 방식에 비해 많은 물리적 우수성 을 보이고 있다. 외발뜨기가 쌍발뜨기에 비해 열단장, 신장율, 인열지수 및 내절도 모두가 우수함을 잘 보이고 있다. 섬유의 성질과 관련하여 전체적으로 조명해 보면, 열단장, 인열 지수는 국산닥이 가장 높으며, 내절도는 태국닥이 우수하였고, 중국닥의 경우 모두 매우 불 량함을 알 수 있다. 이것은 아마도 처리중에 과도한 표백을 실시하지 아니하였는가 하는 의구심을 들게한다. 열단장과 신장율 역시 국산닥이 우수하였다. 글씨를 쓸 때, 붓이 나가 는 정도를 마찰게수로 짐작해 보았다. 동 마찰계수와 정 마찰계수는 국산닥이 낮은 편이였 다. 마찰계수가 낮다는 사실은 한지의 표면이 더 매끄럽다고 표현될 수 있는데, 역시 국산닥 으로 제조한 한지가 붓이 나가는데 유리하지 않을까 하는 추측을 할 수 있다. 본 실험결과 는 한지 사용자들의 느낌과 상관관계를 얻어내어서 확인해야 할 것이다. 닥방망이로의 고해나 칼비터에 의한 고해나 큰 물성적으로 큰 차이를 보이지는 않고 있 었다. 단지 섬유의 차이가 고해방식의 차이보다 월등히 크다는 사실을 보이고 있다 이러한 점은 섬유장의 길이에서도 볼 수 있다. 칼비터가 섬유를 절단하기만 하고 닥방망이 고해가 섬유장의 변화를 일으키지 않는다면 틀림없이 평균 섬유장의 차이가 생길것이다.