• Journal of Korean Society of Forest Science
• /
• v.84 no.4
• /
• pp.409-414
• /
• 1995

This study was carried out for the analysis and comparison about the noise diminution effects by the height, width and density of Euonymus japonica wall, the distance of sound source, the distance of sound receiver, the height of sound source, and the height of sound receiver. The results obtained were summarized as follows; 1. After the establishment of tree wall, the volume of noise diminution measured 6.8dB and the effects of noise diminution measured heigher than before by 10.6% and t-value was significant at the 1% level 2. In simple correlation between the effects of noise diminution and variables, the density of tree wall was found as the most significant factor, and the last were found in the order of the distance of sound receiver, the width of tree wall, and the distance of sound source. 3. In partial correlation coefficients the effects of noise diminution and variables, the density of tree wall (r=-0.959) was found as the most significant factor, and the last were found in order of the distance of sound receiver (r=-0.906) and the width of tree wall (r=-0.753). 4. The estimated equation to measure the effects of noise diminution according to variables (the height of tree wall, the width of tree wall, the density of tree wall, the distance of sound source, the distance of sound receiver, the height of sound source, and the height of sound receiver) was $Y=69.520-1.672X_1-1.656X_2-0.066X_3-0.248X_4-3.134X_5-0.222X_6-0.343X_7$, and the coefficient of determination of this estimated equation was highly found as 0.950. 5. In semi-partial correlation coefficient the effects of noise diminution were found in the order of the density of tree wall, the distance of sound receiver, the width of tree wall, and the height of tree wall from the highest to the lowest. Therefore, it was considered that the density of tree wall, the distance of sound receiver, the width of tree wall and the distance of sound source should be controlled effectively to increase the effects of noise diminution by Euonymus japonica wall.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.520-525
• /
• 2009

본 연구은 해석적인 접근을 통하여 소형엔진 흡기포트 설계인자의 변화에 따른 유량계수를 고찰하였다. 기존모델을 Valve Lift별 유량계수들을 해석하였으며 그 중 유량계수가 일정해지는 구간의 Valve Lift를 기준으로 설계인자 변화에 따른 성능해석을 수행하였다. 결론적으로, 흡기포트 유량계수를 결정하는 중요한 인자는 포트각도와 유선형상임을 확인하였고 이들 값의 최적화를 수행하였다. 흡기포트의 유량계수를 결정하는 설계인자로는 포트각도, 흡기포트의 유선형상, Port Height_Guide, Flange 면적이 있다. 포트각도의 상승이 유량계수를 상승시키지만 그에 따른 굴절 및 Dead Volume의 발생으로 오히려 유량계수 측면에서는 불리한 조건이 되기도 한다. 급격한 형상변화 부분에서 박리현상이 발생되는데 이에 유동을 위한 곡률을 적용하여 급격한 형상변화를 줄여 박리형상을 감쇄시키고, Dead Volume 삭제하여 원활한 유동특성을 만들 수 있다.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.16 no.2
• /
• pp.81-86
• /
• 2012

Purpose : Combined MR/PET scanners that use the MRI for PET AC face the challenge of absent surface coils in MR images and thus cannot directly account for attenuation in the coils. To make up for the weak point of MR attenuation correction, Three Modality System (PET/CT +MR) were used in Severance hospital. The goal of this work was to investigate the effects of MR Torso Coil on CT attenuation correction for PET. Materials and Methods : PET artifacts were evaluated when the MR Torso Coil was present of CTAC data with changing various kV and mA in uniformity water phantom and 1994 NEMA cylinderical phantom. They evaluated and compared the following two scenarios: (1) The uniform cylinder phantom and the MR Torso Coil scanned and reconstructed using CT-AC; (2) 1994 NEMA cylinderical phantom and the MR Torso Coil scanned and reconstructed using CT-AC. Results : Streak artifacts were present in CT images containing the MR Torso Coil due to metal components. These artifacts persisted after the CT images were converted for PET-AC. CT scans tended to over-estimate the linear attenuation coefficient when the kV and mA is increasing of the metal components when using conventional methods for converting from CT number. Conclusion : The presence of MR coils during PET/CT scanning can cause subtle artifacts and potentially important quantification errors. Alternative CT techniques that mitigate artifacts should be used to improve AC accuracy. When possible, removing segments of an MR coil prior to the PET/CT exam is recommended. Further, MR coils could be redesigned to reduce artifacts by rearranging placement of the most attenuating materials.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12A
• /
• pp.1346-1353
• /
• 2007

In this paper, the methods are presented for the calculation of general coupling coefficient matrixes used in the band pass filter design. They are calculated from transmission coefficient($S_{21}$) and reflection coefficient($S_{11}$) with desired characteristics derived from the poles of filter function and return loss(RL). The calculated matrixes from this method are transformed to the folded canonical filter structure using similarity transformation which lends us the practical filter design. Based on the resulting matrix, the folded canonical filter has been designed.

• Journal of Korea Water Resources Association
• /
• v.39 no.9 s.170
• /
• pp.737-744
• /
• 2006

The velocity of the inner region of turbulent flow on a smooth bed has complex profile which can not be described with a simple formula. Though there have been a couple of formulas describing the profile, most of them have very complex forms, i.e., with many terms, with integration form, or with implicit forms. It means that it is hard to use them or it is difficult to estimate their parameters. A new single formula that describes the velocity profile of the inner region of the turbulent flow on a smooth bed was proposed. This formula has a form of the traditional log-law multiplied by a damping function. Introducing only one additional parameter, it can describe the whole inner range nicely. It approximates the law-of-the-wall in the vicinity of the bed and approaches to the log-law in the overlap region. The added parameter, damping factor, can be estimated very easily. It is not sensitive to the Reynolds number change and the velocity profile calculated by the formula does not change much due to the change of the parameter.

• Journal of the Korean Magnetics Society
• /
• v.4 no.1
• /
• pp.1-6
• /
• 1994

The magnetization dynamics was investigated by solving possible origins of overdamped susceptibility observed in ultra-soft magnetic amorphous thin films. The experimental high frequency spectrum and computational spectrum calculated from Gilbert's equation of motion were compared in order to find proper damping factor $\alpha{\approx}20$ and demagnetizing coefficients $D_{x}{\approx}D_{y}{\approx}D_{z}{\approx}0$ for ultra-soft magnetic films. A magnetization vortex mode was, then, proposed to explain the origin of the reversible susceptibility and other anomalies of the ultra-soft magnetic heterogeneous thin films. In this mode it is suggested that there occur, within the nanoscale structural features of the ultra-soft films, incoherent rotational spin motions that are highly damped by the energy transfer from short wavelength spin wave modes and local defect structure mode interactions.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.153-156
• /
• 2000

본 논문에서는 멀티미디어 서비스들 중에서 음성 또는 오디오 신호를 저속으로 압축할 때 사용되는 G.723.1 부호화기의 line spectral frequency(LSF) 계수 양자화 방식을 고속으로 처리하는 알고리즘을 제안하였다. 제안된 고속탐색 방법은 LSF 계수의 순서성질을 이용하여 코드북의 탐색 범위를 줄임으로써 계산량을 크게 감소시킨다. 제안된 고속탐색 방법을 predictive split VQ(PSVQ) 구조를 갖는 G.723.1 에 적용한 결과 spectral distortion(SD) 성능 감쇄 및 추가적인 메모리 증가 없이 최적 코드벡터를 찾기 위한 코드북 탐색 과정에서 코드북의 평균 탐색 범위가 $20.1\%$ 감소했으며, 이는 additions, subtractions, multiplies 및 comparisons 수가 각각 $19.1\%$, $20.1\%$, $19.4\%$ 및 $12.2\% 감소하는 결과를 얻었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.240-240
• /
• 2020

강우 시 우수관로 내부의 수리 거동(유속, 수위)에 영향을 미치는 대표적인 매개변수는 관로의 조도계수와 손실계수 등이 있다. 이 중 조도계수는 관로 내부의 퇴적 및 협잡물로 인한 조도높이 변화에 따른 관로 내의 수리학적 거동을 평가할 수 있는 매개변수이며 손실계수는 관로의 확대, 축소, 만곡 등에 의한 에너지 감쇄 효과에 따른 관로 내 수리학적 변화를 평가할 수 있는 매개변수이다. 본 연구에서는 서울시 주요 배수구역에 대해 관로 조도계수 및 손실계수 변화에 따른 수위, 유속 변동성을 SWMM으로 분석하였다. 연구에 적용한 대상 배수구역은 반포 02 (방배1), 안양천 13 (봉천1), 성내 05 (길동), 안양천 11(신림4), 반포 03 (방배2), 안양천 01 (오류1), 성내 03 (천호)로 총 7개 배수구역이다. 모형수행을 위한 조건으로 조도계수는 0.015 ~ 0.120 구간에 대해 0.003 단위로 증가시키며 총 12개 CASE를 적용하였으며 손실계수는 0.0 ~ 0.5 구간에 대해 0.1 단위로 총 6개 CASE를 적용하였다. 관로 수리특성에 따른 수심, 유속의 변화량 분석 결과는 관로 및 유역의 크기별로 변화의 폭이 매우 크므로 상자-수염그림(Box-whisker plot) 이용하여 중간값의 변화 정도를 검토하였다. 조도계수 증가에 따른 수심증가, 유속 감소치의 중간값을 분석한 결과 조도계수가 0.013에서 0.034로 증가 시 수심은 40.6% 증가하고 유속은 47.4% 감소하는 것으로 검토되었다(그림 1, 2). 한편, 손실계수 증가에 따른 수심증가, 유속 감소치의 중간값을 분석한 결과 조도계수가 0.0에서 1.6으로 증가시 수심은 15.7% 증가하고 유속은 15.0% 감소하는 것으로 검토되었다. 이상과 같은 연구의 성과는 우수관로 내부의 다양한 여건 변화가 강우 시 관로 내 수리특성에 미치는 영향을 판단하기 위한 기초 자료로 활용할 수 있으며 향후, 우수관로 모니터링 결과와 연계하여 유지관리 방안 수립에 활용할 수 있을 것으로 판단된다.

• Nuclear Engineering and Technology
• /
• v.27 no.6
• /
• pp.811-824
• /
• 1995

The CANDU element bowing is attributed to actions of both the thermally induced bending moments and the bending moment due to hydraulic drag and mechanical loads, where the bowing is defined as the lateral deflection of an element from the axial centerline. This paper consider only the thermally-induced bending moments which are generated both within the sheath and the fuel and sheath by an asymmetric temperature distribution with respect to the axis of an element The generalized and explicit analytical formula for the thermally-induced bending is presented in con-sideration of 1) bending of an empty tube treated by neglecting the fuel/sheath mechanical interaction and 2) fuel/sheath interaction due to the pellet and sheath temperature variations, where in each case the temperature asymmetries in sheath are modelled to be caused by the combined effects of (i) non-uniform coolant temperature due to imperfect coolant mixing, (ii) variable sheath/coolant heat transfer coefficient, (iii) asymmetric heat generation due to neutron flux gradients across an element and so as to inclusively cover the uniform temperature distributions within the fuel and sheath with respect to the axial centerline. As the results of the sensitivity calculations of the element bowing with the variations of the parameters in the formula, it is found that the element bowing is greatly affected relatively with the variations or changes of element length, sheath inside diameter, average coolant temperature and its variation factor, pellet/sheath mechanical interaction factor, neutron flux depression factor, pellet thermal expansion coefficient, pellet/sheath heat transfer coefficient in comparison with those of other parameters such as sheath thickness, film heat transfer coefficient, sheath thermal expansion coefficient and sheath and pellet thermal conductivities.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.1
• /
• pp.35-40
• /
• 1982

As a general-purpose device, the microprocessor has made a large impact on many area of engineering, In this paper, a controller has been implemented using microprocessors allowing the damping ratio ζ to be changed dynamically in control systems. The results show definite improvement in response time.