• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.2
• /
• pp.91-97
• /
• 2000

Tn this paper, a novel control circuit applicable to the error sensor loop block in the feedforward linearizer system is proposed. The proposed control circuit is applied to the error sensor loop block, where in the 11dB power range, it operates stably, and makes main carrier signals to be eliminated more than 40dB below 3$\^$rd/ order IM level. In the operating point, the amplitude control error is 0.05∼0.12dB, and the phase control error is smaller than 0.02。. It is verified theoretically as well as experimentally that the control circuit can precisely compensate the variation of nonlinear characteristics in a high power amplifier, due to the variations of input power, operating temperature, humidity and the other system environments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.6A
• /
• pp.499-509
• /
• 2005

The capacity of Satellite DMB(Digital Multimedia Broadcasting) system is limited mainly by the interference. So, to achieve the expected performance of Satellite DMB system and to minimize the interference from other Satellite DMB system, ACI(Adjacent Channel Interference) should be considered carefully. Satellite DMB system uses the Gap-filler for effective transmission in terrestrial environment, and the Gap-filler can use direct amplification or frequency conversion to satisfy the specific requirements. Therefore, amplified signal causes several effects on interference between System A(Eureka 147 DAB) and System E(ISDB : Integrated services Digital Broadcasting). In this paper, by using the outcome of system-level simulation considering the results of link-level simulation, we analyze the interferences between System A and System E under practical situation based on the exact parameters of ITU-R BO. 1130-4. We also propose the appropriate level of guard band and Cell Radius to optimize system capacity by adapting the spectrum mask given in the spec. and utilizing the interference analysis between System A and System E.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.1B
• /
• pp.90-98
• /
• 2002

To increase system capacity in WCDMA receiver, the coherent detection is an essential technology for recovering transmitted symbols correctly. For coherent detection, an accurate and fast channel estimation is required. In next generation mobile communication system, high frequency carriers are used, and high data rate services are provided for subscribers having high mobility. In this communication environment, however, the rapidly-changing doppler frequency degrades the quality of the transmitted signal a lot. In WCDMA system, the channel estimation is conducted using pilot channel and/or pilot symbols which are known to both transmitter and receiver. Some existing channel estimation algorithms utilize these information quite well, but the performance of channel estimation gets very poor in a complicated fading channel distorted by the doppler effect. In this paper, we propose a new channel estimation algorithm combining an early-late doppler compensator so that the doppler effect and the fading characteristics are compensated at the same time. By computer simulation, the proposed algorithm proved to be a much more efficient channel estimation method in the fast fading channel, even at reasonably low Eb/No.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.3
• /
• pp.1-9
• /
• 2003

In this paper, we designed a highly suppressed sidelobe ladder type RF SAW bandpass filter based on 1-port resonator, for 800 MHz mobile communication system. In order to get the highest device characteristics, we optimized some important parameters such as the electrode thickness, electrode lambda weghting of the reflectors, and static capacitance ratio. Furthermore, we fabricated the Tx and Rx. filter using optimized parameters. Implemented filters can be used in 800 MHz mobile communication system and external impedance matching circuits are not needed. RF filter was fabricated on 36$^{\circ}$LiTaO$_3$ substrates with Al-Cu (W 3 %)and mounted 3.8mm$\times$3.8mm$\times$1.5mm SMD package. Developed filters has 2.3 dB insertion loss in the 25 MHz pass-band, 33MHz with 3-dB insertion loss, stop-band rejection of 30 dB, passband ripple is less than 0.5 The power durability of the filters measured about 3.5W and the maximum temperature variation within -2$0^{\circ}C$~8$0^{\circ}C$ was 0.09 dB/$^{\circ}C$ of 3-dB insertion loss.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.395-402
• /
• 2002

In the conventional public switched telephone network(PSTN), there are various types of modulation that can be used in ADSL to offer fast data communication, two of which are CAP(Carrierless Amplitude Phase) and DMT(Discrete MultiTone). As we consider the current situation, DMT is getting more predominant in the market than CAP. One of the reasons is that it gives high performance in spite of its high complexity Since DMT divides the full range of bandwidth into 256 sub-channels, it can be highly adaptive in the circumstances, where the problems of attenuation and noise caused by the propagation distance are very crucial. In this paper, a new bit loading algorithm for DMT modulation is proposed. The proposed algorithm can be efficiently implemented in a way that it requires less computation than the conventional modulation techniques. In contrast to the conventional algorithms which perform sorting processing, the proposed algorithm uses look-up tables to reduce the repetition of calculation. Consequently, it is shown that less processing time and lower complexity can be achieved.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.7
• /
• pp.709-715
• /
• 2011

Harmonic drives have been widely used in combination with joint torque sensors in order to facilitate accurate manipulator control. A harmonic drive causes a torque ripple because of its structural characteristics, and this torque ripple tends to deteriorate the performance of a controller or observer that uses torque sensors. This paper proposes a switching notch filter for reducing the torque ripple caused by a harmonic drive in a joint torque sensor; the functioning of this filter is based on the relationship between the frequency components of the torque ripple and the rotational velocity of the harmonic drive. The proposed switching notch filter is advantageous in that it requires less computational load and does not necessitate additional circuits or structures. Various experiments demonstrate that the proposed filter has good filtering performance, fast response, and good switching stability.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.138-144
• /
• 2017

In this paper, we propose a high frequency boosting circuits compensating for age-related hearing loss. The frequency response of this hearing loss is quite similar to that of a low-pass filter of which the critical frequency get lower with age. Therefore the voltage gain of this compensation circuits increase proportionally to the frequency of signals when the frequency is higher than the critical frequency and the voltage is constant irrespective of the frequency of signals when the frequency is lower than the critical frequency. The proposed circuits consist of a differential circuit and a unity gain amplifier. Because the critical frequency of the proposed circuits is controlled simply in the shape of a volume control lever, the aged people can adjust the high frequency boosting level easily according to one's hearing loss level. The critical frequency is continuously controllable in the whole audible frequency band and the gain of this high frequency boosting circuits is above 80dB at 10kHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.101-106
• /
• 2005

A ground penetrating image radar (GPR) using an ultra wideband (UWB)impulse waveform is developed for non destructive detection of metallic pipelines buried under the ground. Dielectric constant of test field is measured and then a GPR system is designed for better detection up to 1 meter deep. By considering total path loss, volume of complete system, and resolution, upper and lower frequencies are chosen. First, a UWB impulse for the frequency bandwidth of the impulse is chosen with rising time less than 1 ns, and then compact planar UWB dipole antenna suitable for frequency bandwidth of a UWB impulse is designed. Also, to receive reflected signals, a digital storage oscilloscope is used. For measurement, a monostatic technique and a migration technique are used. For visualizing underground targets, simple image processing techniques of A-scan removal and B-scan average removal are applied. The prototype of the system is tested on a test field in wet clay soil and it is shown that the developed system has a good ability in detecting underground metal objects, even small targets of several centimeters.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.25-30
• /
• 2006

When wet soil overlies dry soil, which can be found in the infiltration test, the radar wave is not attenuated and guided within wet soil layer. This phenomenon is known to be the dispersive guided wave and happens when the thickness of upper wet layer is less than or comparable to the wavelength of radar wave. In this study, we have conducted the FDTD modeling and obtained the velocity dispersion curve to identify the dispersive guided wave through F-K analysis. This guided wave can be explained by modal propagation theory and a simple inversion code was developed to obtain the two layer's dielectric constants as well as layer thickness. By inverting the dispersion curve from synthetic modeling data, we could obtain the accurate dielectric constants and layer thickness. Moreover, we could enhance the accuracy by including the higher mode data. We expect this method will be very useful to get the quantitative property of subsurface when the condition is similar.

• Tunnel and Underground Space
• /
• v.16 no.2 s.61
• /
• pp.156-165
• /
• 2006

Already, vari-stem, gas-bag, power deck, air ball etc. are used by various blasting methods to take the advantage of air decking technology in abroad. Air tube product has been used continuously in domestic and air ball product was made recently. In the case study, we analyzed about the application and the effect or air deck blasting method in domestic blasting area. As results or this case study, it was shown that blasting vibration was decreased about $21{\sim}41%$ and quantities or explosives was decreased about $17{\sim}30%$. Also, in the case of using air deck blasting method, fragmentation was shown to be smaller than common blasting method.