• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.6
• /
• pp.639-646
• /
• 2012

The characteristics of autoignited lifted flames in laminar jets of carbon monoxide/hydrogen fuels have been investigated experimentally in heated coflow air. In result, as the jet velocity increased, the blowoff was directly occurred from the nozzle-attached flame without experiencing a stabilized lifted flame, in the non-autoignited regime. In the autoignited regime, the autoignited lifted flame of carbon monoxide diluted by nitrogen was affected by the water vapor content in the compressed air oxidizer, as evidenced by the variation of the ignition delay time estimated by numerical calculation. In particular, in the autoignition regime at low temperatures with added hydrogen, the liftoff height of the autoignited lifted flames decreased and then increased as the jet velocity increased. Based on the mechanism in which the autoignited laminar lifted flame is stabilized by ignition delay time, the liftoff height can be influenced not only by the heat loss, but also by the preferential diffusion between momentum and mass diffusion in fuel jets during the autoignition process.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.1
• /
• pp.57-62
• /
• 1999

Polycrystaline thin film transistors are fabricated on the transparent glass substrate by a lamp-scan annealing. The line-shaped lamp scanning method, which is profitable for large area process, effectively radiated silicon film on glass substrate. Amorphous silion film absorbs the light which is emitted from halogen-lamp and it transformed into crystalline silicon by metal-induced lateral crystallization. In order to enhance the annealing effect, capping layer was deposited on the whole substrate. When the scan speed was 1-2mm/sec, lateral crystallization of amorphous silicon under capping layer was 18~27${\mu}m/scan$. The thin film transistor fabricated by this method shows high electron mobility over 130$cm^2/V{\cdot}sec$

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.551-560
• /
• 1988

Gas-particle two phase flow and heat transfer in a cavity receiving thermal radiation through selectively transparent walls have been analyzed by a finite difference method. Particles injected from the upper hole of the cavity are accelerated downward by gravity and exit through the lower hole while they absorb, emit and scatter the incident thermal radiation. Gas phase is heated through convection heat transfer from particles, and consequently buoyancy induced flow field is formed. Two-equation model with two-way coupling is adopted and interaction terms are treated as sources by PSI-Cell method. For the particulate phase, Lagrangian method is employed to describe velocities and temperatures of particles. As thermal radiation is incident upon horizontally, radiative heat transfer in the vertical direction is assumed negligible and two-flux model is used for the solution of radiative heat flus. Gas phase velocity and temperature distributions, and particle trajectories, velocities and temperatures are presented. The effects of particle inlet condition, particle size, injection velocity and particle mass rate are mainly investigated.

• Ocean and Polar Research
• /
• v.27 no.1
• /
• pp.87-95
• /
• 2005

The vertical profiles of radiative flux and heating rate at King Sejong Station in West Antarctica were calculated with radiative transfe model by Chou and Suarez (1999) and Chou et al (2001). To run this model, the profiles of temperature, mixing ratios of water vapor and ozone at King Sejng Station were derived from ECMWF Reanalysis data. The surface temperature and albedo were also derived from NCEP/NCAR Reanalysis and CERES data. The radiative flux strongly depends on the cloud optical path length that was calculated using the measured W-h data and model by Chou and Lee(1996). Durins the period of $2000{\sim}2001$ (12 and 18 UTC), the correlation coefficient between calculated and measured downward solar fluxes at surface was 0.90 and the coefficient for downward longwave flux was 0.61. The calculated net heating rates of surface layer decreased during the same period, the trend of which was in accordance with the decrease of measured temperature.

• Korean Journal of Food Science and Technology
• /
• v.16 no.4
• /
• pp.451-456
• /
• 1984

Rheological properties of gelatinized rice starch solutions were investigated with Brookfield rotational viscometer. The 8% starch solution showed thixotropic behavior with yield stress. The alkali gelatinized starch was more thixotropic than the thermal gelatinized one. The time dependent characteristics of starch solutions followed Tiu's model. The value of rate constant $(a_1)$ in Tiu's model increased linearly with shear rate, and was exponentially dependent on concentration and temperature. Temperature dependency of rate constant and apparent viscosity followed Arrhenius type equation and the activation energy were about 14.3 and 6.8 Kcal/g mole, respectively. The $a_1-value$ was found to be useful to evaluate changes in structaral decay on the shearing time of gelatinized rice starch solutions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.2
• /
• pp.314-321
• /
• 1987

Post weld heat treatment (PWHT) of weldment of the low alloy Cr-Mo steel, in general, is carried out not only to remove residual stress and hydrogen existing in weldment but to improve fracture toughness of weld heat affected zone (HAZ). There occur some problems such as toughness decrement and stress relief cracking (SRC) in the coarse grained region of weld HAZ when PWHT is practiced. Especially, embrittlement of structure directly relates to the mode of fracture and is appeared as the difference of fracture surface such as grain boundary failure. Therefore, in this paper, the effect of heating rate on PWHT embrittlement under the various kinds of stresses simulated residual stress in weld HAZ was evaluated by COD fracture toughness test and observation of fracture surface. Fracture toughness of weld HAZ decreased with increment of heating rate under no stress, but it was improved to increment of heating rate under the stress. Grain boundary failure didn't almost appear at the heating rate of 600.deg.C/hr but it appeared from being the applied stress of 294 MPa at 220.deg.C/hr and 196 MPa at 60.deg.C/hr.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.103-109
• /
• 2016

Polyethylene pipes has useful benefits which are anti-corrosive and flexible material, so it is used to gas pipes but also class 3 water pipes of nuclear power plant, process pipes of petrochemical plant and chemical plant. So the usage of polyethylene pipes is widely increased. But it has been limited for the usage of polyethylene, because it can not be directly detected to fusion joints by using non destructive evaluation. Polyethylene pipes are connected by two methods, one is butt fusion and the other is electrofusion. Butt fusion is widely used to connecting the pipes. It is proposed to method for determining the reliability of joints in this study that is detection of the melt flow zone at fusion joints. In this study, middle density polyethylene is used, outside diameter of the test specimen is 225mm and thickness is 20.5mm. Speed of ultrasonic of this test specimen is 2,200m/s. Test specimens were fabricated by varying the heating time which means from 0% to 130% applying time through heating plate to polyethylene for detecting melt flow zone. Also 4 additional test specimens were made, one was made that not scrapping attached surface of pipes but applying 100% of the proper heating time and the others were made to include of soil, gravel and vinly tape paper at fusion joints, that were also applied 100% of proper heating time. Ultrasonic testing to measure the melt flow zone of 20 test specimens was conducted by using 3.5MHz and 5.0MHz ultrasonic probes and melt flow zone measuring was conducted to three times at different point to one specimen. To differentiate the melt flow zone signal, post image processing was equally conducted to all test results and image levels, contrast, sharpen, threshold were adopted to all teat results and the test results were displayed gray scale. From the results, for the shorter heating times the reflection area of multiple echo have been increased, so the data was obtained from the position where it can be eliminated as much as possible. At 80% of proper heating time(168 sec.), the signal of melt flow zone was obtained clearly, so measuring could be conducted. From 7% of proper heating time(15 sec.) to shorter heating times. we could not obtain the signal because test specimen was not fused. From the result, we can verify that measuring of melt flow zone by using phased array ultrasonic imaging method is possible. And we can verify to complete and incomplete butt fusion by measuring the melt flow zone.

• Applied Biological Chemistry
• /
• v.10
• /
• pp.39-45
• /
• 1968

Maillard 반응(反應)에서 생성(生成)된 가용성(可溶性) 혼합물질(混合物質) "Premelanoidines"의 Saccharomyces cerevisiae에 의(依)한 주정발효(酒精醱酵)에 미치는 생리적(生理的) 영향에 관(關)해서 관찰하였다. Premelanoidines은 포도당과 Glycine의 수용액(水溶液)을 $90^{\circ}C$에서 $1{\sim}48$시간(時間) 가열(加熱)함으로써 얻었으며 이의 주정발효(酒精醱酵)에 미치는 생리적(生理的) 영향은 Micro-Warburg를 사용(使用)하여 주정발효(酒精醱酵) 과정중(過程中) 발생(發生)되는 $CO_2$의 량(量)을 측정(測定)함으로써 발효속도(醱酵速度)의 촉진(促進)여부를 결정(決定)하였다. 실험결과(實驗結果)를 종합(綜合)해 보면, Premelanoidines은 효모(酵母)에 의(依)한 주정발효(酒精醱酵)의 속도(速度)를 촉진(促進)하는 결과(結果)를 나타냈으며 이 촉진현상(促進現象)은 어느 한계내(限界內)에서 발효(醱酵)배지에 함유(含有)된 Premelanoidines의 량(量)에 비례(比例)하여 증가(增加)한다. 또한 이 Premelanoidines의 활성(活性)은 특(特)히 발효(醱酵)의 초기(初期)에 한(限)하여 작용(作用)하는 것을 알 수 있었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.536-547
• /
• 1997

For various angular velocities of crucible and crystal, the characteristics of melt flows, temperatures and concentrations of oxygen are numerically studied in the Czochralski furnace with a uniform axial magnetic field. Buoyancy effect due to the heating of crucible wall and thermocapillary effect due to the temperature gradient at the free surface, can be differentiably suppressed by the centrifugal forces due to the rotations of the crucible and crystal. The most important factor which yields the centrifugal forces is the rotation velocity of the crucible, that influences the fields of velocities, temperatures and concentrations. In the case that the crucible rotation velocity is not high, the rotations of the crystal gives rise to the centrifugal forces effectively.

• Resources Recycling
• /
• v.6 no.1
• /
• pp.40-46
• /
• 1997

Sludgc d~sposal has been a major challenge in the wastewater treatment. Drying is operation which is separated fromsewage sludge to solid and liquid by heating. Drying needs to pretreatment process for effective "thation, incinerationand dispaal The objective of this work was to the drying dewatered sewage sludge by microwave heating, and tocompare the experimental rcsults with thcorctical rcsults. Microwave drylng is fast and has a high efficiency. In thepresent \ark, an unsteady state analysis of one dunensional drying, with microwave heating, is carried out. In drying ratecurve, moisture movement at falling rate period occured by dfision. A good agreement was abtamed between the modcland the experimental results using the slab sample of 0.2cm thickness. 0.2cm thickness.