• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.5
• /
• pp.887-892
• /
• 2019

In this study, after 20nm-thick $SiO_2$ thin film was deposited by PECVD method on the PES substrate, which is known to have the highest heat resistance among plastic substrates, as a buffer layer, ITZO thin films were deposited by RF magnetron sputtering method to investigate the electrical and optical properties according to the working pressure. The ITZO thin film deposited at the working pressure of 3mTorr showed the best electrical properties with a resistivity of $8.02{\times}10^{-4}{\Omega}-cm$ and a sheet resistance of $50.13{\Omega}/sq.$. The average transmittance in the visible region (400-800nm) of all ITZO films was over 80% regardless of working pressure. The Figure of merit showed the largest value of $23.90{\times}10^{-4}{\Omega}^{-1}$ in the ITZO thin film deposited at 3mTorr. This study found that ITZO thin films are very promising materials to replace ITO thin films in next-generation flexible display devices.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.343-348
• /
• 2003

Indium tin oxide (ITO) thin films (170 nm) were grown by DC magnetron sputtering deposition on Coming glass substrates without a post annealing. The electrical transport and optical properties of the films have been investigated as a function of deposition temperature $T_{s}$ (10$0^{\circ}C$$\leq$ $T_{s}$$\leq$35$0^{\circ}C$) and oxygen partial pressure $P_{o_{2}}$, (0 $P_{o_{2}}$ $\leq$ 10$^{-5}$ torr). Films were deposited from a high density (99% of theoretical density) ITO target (I $n_2$ $O_3$: Sn $O_2$= 90 wt% : 10 wt%) made of ITO nano powders. With an increase of $T_{s}$ the electrical resistivity p of ITO thin films was found to decrease, but the mobility $\mu$$_{H}$ was found to increase. The carrier density nu shows the maximum value of 6.6$\times$10$^{20}$ /㎤ at $T_{s}$ = 30$0^{\circ}C$. At fixed Is, with an increase of the oxygen partial pressure, $n_{H}$ and $\mu$$_{H}$ were found to decrease, but p was found to increase. The minimum resistivity and maximum mobility values of the ITO films were found to be 0.3 mΩ.cm and 39.3 $\textrm{cm}^2$/V.s, respectively. The visible transmittance of the ITO films was above 80%.. 80%..

• Korean Journal of Optics and Photonics
• /
• v.13 no.5
• /
• pp.455-459
• /
• 2002

The transport and optical properties of $In_2O_3$:Zn(IZO) thin films grown by DC magnetron sputtering deposition have been studied. The deposition temperatures ($T_s$) were varied from room temperature to $400^{\circ}C$ in $50^{\circ}C$ steps. The IZO films are an amorphous phase for $T_s$<$300^{\circ}C$ and polycrystalline phase for $350^{\circ}C$＜$T_s$. In contrast to ordinary films, amorphous IZO films have lower resistivity and higher optical transmittance than polycrystalline IZO films. The resistivity of amorphous IZO was in the range of 0.29~0.4 m$\Omega$cm and that of polycrystalline IZO was in the range of 1~4 m$\Omega$cm. The carrier type for IZO film was found to be n-type, and the carrier density, was $3~5{\times}10^{20}/cm^3$. The Hall mobility, $({\mu}_H)$, was 20~$50\textrm{cm}^2$/V.sec. The predominant scattering mechanisms in both amorphous and polycrystalline IZO films were believed to be ionized impurity scattering and lattice scattering. The visible transmittance of the IZO films, which decreases with an increase of TS, was above 80%.

• Korean Journal of Optics and Photonics
• /
• v.19 no.4
• /
• pp.287-293
• /
• 2008

The collimator which makes a collimated beam, is an essential instrument for assembly and evaluation of telescopes. Recently, the Cassegrain type collimator has been widely used for its compact size as the focal length of high resolution cameras becomes longer. However, this kind of collimator has a disadvantage in that the secondary mirror is a heat source which can degrade the evaluation accuracy for an IR camera system. In this paper, we present the fabrication and measurement process for an off-axis parabolic mirror with the physical diameter pf 1 m, effective diameter 930 mm, and the focal length 6 m. After four months of works we obtained the final surface wave-front error of 30.4 nm rms ($\lambda$/138, ${\lambda}=4.2\;{\mu}m$), which is capable of evaluation of an IR camera as well as a visible camera.

• The Journal of Bigdata
• /
• v.6 no.1
• /
• pp.145-151
• /
• 2021

In recent years, digital data has been generated in all areas of human activity, and there are many attempts to safely store and process the data to develop useful services. A data lake refers to a data repository that is independent of the source of the data and the analytical framework that leverages the data. In this paper, we designed a tool to safely store various big data generated by smart cities in a data lake and ETL it so that it can be used in services, and a web-based tool necessary to use it effectively. Implement. A series of processes (ETLs) that quality-check and refine source data, store it safely in a data lake, and manage it according to data life cycle policies are often significant for costly infrastructure and development and maintenance. It is a labor-intensive technology. The mounting technology makes it possible to set and execute ETL work monitoring and data life cycle management visually and efficiently without specialized knowledge in the IT field. Separately, a data quality checklist guide is needed to store and use reliable data in the data lake. In addition, it is necessary to set and reserve data migration and deletion cycles using the data life cycle management tool to reduce data management costs.

• Journal of Broadcast Engineering
• /
• v.26 no.4
• /
• pp.409-418
• /
• 2021

Conformal coating is a technology that protects PCB(Printed Circuit Board) and minimizes PCB failures. Since the defects in the coating are linked to failure of the PCB, the coating surface is examined for air bubbles to satisfy the successful conditions of the conformal coating. In this paper, we propose an algorithm for detecting problematic bubbles in high-risk groups by applying image signal processing. The algorithm consists of finding candidates for problematic bubbles and verifying candidates. Bubbles do not appear in visible light images, but can be visually distinguished from UV(Ultra Violet) light sources. In particular the center of the problematic bubble is dark in brightness and the border is high in brightness. In the paper, these brightness characteristics are called valley and mountain features, and the areas where both characteristics appear at the same time are candidates for problematic bubbles. However, it is necessary to verify candidates because there may be candidates who are not bubbles. In the candidate verification phase, we used convolutional neural network models, and ResNet performed best compared to other models. The algorithms presented in this paper showed the performance of precision 0.805, recall 0.763, and f1-score 0.767, and these results show sufficient potential for bubble test automation.

• Korean Journal of Ichthyology
• /
• v.33 no.2
• /
• pp.148-154
• /
• 2021

Two specimens (1770~1850 mm disc width) of Mobula thurstoni, belonging to the family Myliobatidae, order Myliobatiformes, were first collected from the central coast of the Southern Sea of Korea in September 2018. This species is characterized by an anterior margin of disc with double curvature, a white-tipped dorsal fin, and the absence of a caudal spine. This species is morphologically similar to Mobula kuhlii, but has an anterior margin of pectoral fins with a double curvature and the dorsal coloration is bluish black rather than white. In addition, M. thurstoni was well distinguished from M. kuhlii as determined by mitochondrial DNA 16S rRNA sequences with genetic distances ranging from 0.030 to 0.069. The Korean name 'Mae-kkeun-kko-li-jwi-ga-o-li' is proposed for the species M. thurstoni.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.497-504
• /
• 2019

We fabricated $HfO_2$ thin films using RF magnetron sputtering method, and investigated structural and optical properties of $HfO_2$ thin films with RTA temperatures in $N_2$ ambient. $HfO_2$ thin films exhibited polycrystalline structure regardless of annealing process, FWHM of M (-111) showed reduction trend. The surface roughness showed the smallest of 3.454 nm at a annealing temperature of $600^{\circ}C$ in result of AFM. All $HfO_2$ thin films showed the transmittance of about 80% in visible light range. By fitting the refractive index from the transmittance and reflectance to the Sellmeir dispersion relation, we can predict the refractive index of the $HfO_2$ thin film according to the wavelength. The $HfO_2$ thin film annealed at $600^{\circ}C$ exhibited a high refractive index of 2.0223 (${\lambda}=632nm$) and an excellent packing factor of 0.963.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.4
• /
• pp.179-186
• /
• 2019

In this study, we investigated the structural properties of $Ga_2O_3$ thin films and the photo-electrical properties of metal-semiconductor-metal (MSM) photodetectors deposited by Ti/Au electrodes. $Ga_2O_3$ thin films were grown at different temperatures using metal organic chemical vapor deposition (MOCVD). The crystal phase of $Ga_2O_3$ changed from ${\varepsilon}$-phase to ${\beta}$-phase depending on the growth temperature. The crystal structure of ${\varepsilon}-Ga_2O_3$ was confirmed by X-ray diffraction (XRD) analysis and the formation mechanism of crystal structure was discussed by scanning electron microscopy (SEM) images. From the results of current-voltage (I-V) and time-dependent photoresponse characteristics under the illumination of external lights, we confirmed that the MSM photodetector fabricated by ${\varepsilon}-Ga_2O_3$ showed much better photocurrent characteristics in the 266 nm UV range than in the visible range.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.443-450
• /
• 2021

After selecting a PES substrate with excellent thermal stability and optical properties among plastic substrates, a SiO₂ thin film was deposited as a buffer layer to a thickness of 20nm by plasma-enhanced chemical vapor deposition to compensate for the high moisture absorption. Then, the ITZO thin film was deposited by a RF magnetron sputtering method to investigate electrical and optical properties according to RF power. The ITZO thin film deposited at 50W showed the best electrical properties such as a resistivity of 8.02×10^-4 Ω-cm and a sheet resistance of 50.13Ω/sq.. The average transmittance of the ITZO thin film in the visible light region(400-800nm) was relatively high as 80% or more when the RF power was 40 and 50W. Figure of Merits (Φ_TC and FOM) showed the largest values of 23.90×10^-4 Ω^-1 and 5883 Ω^-1cm^-1, respectively, in the ITZO thin film deposited at 50W.