• Transactions of Materials Processing
• /
• v.10 no.5
• /
• pp.402-410
• /
• 2001

The gas-assisted injection molding process is often perceived to be unpredictable, because of the extreme sensitivity of the gas. Since a slight change in design or process parameters can significantly change the resulting gas penetration, few designers and molders have the level of experience with the new gas-assisted injection molding process required for the development of new parts. This paper is concerned with the unified molding for a thick cosmetic chest by using gas-assisted injection molding. CAE analysis was carried out to design the part and the gas channel without inducing sink marks. And based on the part weight measurement, the processing parameters to control gas penetration percentage were chosen through the method of design of experiments. A thick cosmetic chest was successfully produced using the gas assist technology. The sink mark issue associated with the conventional injection molded parts was resolved. Weight savings and cycle-time reduction were also achieved.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1193-1194
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.852-855
• /
• 2003

Gas-Assisted Injection Molding(GAIM) process, that can be used to provide a hollow shape in a molding, is a variant of the conventional injection molding process. GAIM has many advantages such as reduction of material, sink mark. warpage. and lower injection pressure. Thus, GAIM has been widely applied in the industry to make moldings with a hollow channel such as handles, TV frames and so on. On the other hand, GAIM has some disadvantages such as slow cooling time and flow marks. In the disadvantages, hot gas core causes slow cooling of a molding and the overflow. which is to prevent flow mark. is waste of materials. To solve these problems, we developed a new GAIM system that we called RGIM(Reverse Gas Injection Molding). The RGIM has two special units; one is the overflow buffer, which is used for reduction of a material, and the other tile air unit, which is used for faster cooling of a molding. We conducted an experiment and simulation to verify the efficiency of the RGIM system. Through experiments and simulation, we confirmed the effectively operating of the RGIM system and extracted the optimum process conditions.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1710-1714
• /
• 2005

Micro Cellular Plastics create a sensation at polymer industrial for lowering product cost & overcoming a lowering of mechanical intensity. This research is surface quality research of MCPs product Through surface rough measurement. This experiment is carried out according to injection speed control with the surface rough & Product surface quality are searched

• Food Engineering Progress
• /
• v.21 no.2
• /
• pp.150-157
• /
• 2017

The objective of this study was to determine the effect of moisture contents (40, 50, 60%) and $CO_2$ gas injection (0 and 800 mL/min) on physicochemical properties of extruded soy protein isolate (SPI). The expansion ratio and the specific length increased, but piece density decreased with the increase in $CO_2$ gas injection from 0 to 800 mL/min at both 40 and 50% moisture contents. On the contrary, the expansion ratio and the specific length decreased, but piece density increased with the increase in $CO_2$ gas injection from 0 to 800 mL/min at 60% moisture content. Extruded SPI with $CO_2$ gas injection at 800 mL/min had small cell size and higher amount of cell than extruded SPI without $CO_2$ gas injection. The water holding capacity and nitrogen solubility index increased, and the integrity index and the texture decreased with the increase in $CO_2$ gas injection from 0 to 800 mL/min. In conclusion, extruded SPI with the $CO_2$ gas injection at 800 mL/min showed better expansion properties and cell formation than extruded SPI without the $CO_2$ gas injection.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.131.2-135
• /
• 1999

This study focuses on part quality and cycle times under gas-assisted injection molding(GIM) of housing molded parts. The position of the gas channel was estabished near to parting line at the end of last locations to fill. Applied hot runner and valve gates the gas was introduced directly into the mold cavity via gas pin. As GIM was applied the introduced directly into the mold cavity via gas pin. As GIM was applied the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture ii) The realibility was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout iii)It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM iv)The productivity were improved by reducing cycle times.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.276-283
• /
• 1999

This study focuses on part quality and cycle times under gas-assisted injection molding (GIM) of box shape molded parts. The position of the gas channel was established near to parting line at the end of last locations to fill. Applied hot runner and valve gates, the gas was introduced directly into the mold cavity via gas pin. As GIM was applied, the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture. ii) The reliability was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout. iii) It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM. iv) The productivity were improved by reducing cycle times.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• Transactions of Materials Processing
• /
• v.21 no.2
• /
• pp.107-112
• /
• 2012

Gas-assisted injection molding(GAIM) produces parts with hollow internal sections. The technique offers benefits to powder injection molding(PIM), with lower material usage and reduced time for de-binding processes. In this study, the effects of processing parameters on gas penetration length of gas-assisted powder injection molding(GAPIM) were investigated for SUS316L stainless steel powder feedstock. Experiments were planned based on the Taguchi method, involving processing variables such as melt temperature, shot size, gas pressure, and gas delay time. The most significant parameters affecting gas penetration length were gas delay time and shot size, while the effects of melt temperature and gas pressure was relatively insignificant.

• The Korean Journal of Rheology
• /
• v.7 no.3
• /
• pp.237-249
• /
• 1995

폴리우레탄 미세포 포움의 가공에 대한 연구를 수행하였으며 기체 과포화 수지 내 의 핵생성율을 증진시키기 위하여 폴리올과 이소시아네이트의 혼합물에 초음파 가진을 적용 하였다. 미세포 구조는 고압에서 질소 가스로 폴리올을 과포화ㅣ키고 폴리우레탄의 두 성분 을 충돌혼합시킨 직후 초음파에 의해 기포를 생성시켜 이루어진다. 낮은 포화 압력에서 질 소에 의해 포화된수지의 핵생성율을 증가시키기위하여 초음파 가진을 적용하였다. 확산에 의해 기포의 성장이 조절된다고 가정하고 금형이 충전되는 동안에 금형 내부에서의 기포성 장기구를 이해하기 위하여 수치적인 방법으로 이론적 연구를 수행하였다. 경화 시간과 확산 경계를 고려하여 최종적인 기포의 크기를 계산하였으며 반응속도론을 고려하여 중합반응 동 안의 폴리우레탄의 점도의 변화를 예측하고 경화 시간을 결정하였다. 이론적 및 실험적으로 결정된 기포의 수를 기준으로 하여 확산 경계를 예측하였다.