• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.177-180
• /
• 2010

Two-stage light gas gun, sorted with Ballistic Range System, is used to research spray characteristics of supersonic liquid jets. When high pressure tube was pressurized to the 135 bar, diaphragm films which composed with OHP film are ruptured. Expansion gases accelerate a projectile approximately 250 m/s at the exit of pump tube. And accelerated projectile collides with liquid storage part and liquid jets were injected into supersonic conditions. Supersonic liquid jets show the multiple jets and generate shockwave at the forward region of jets. Supersonic liquid jets of speed and shockwave angle have different value at each case. Supersonic liquid jets with minimum velocities are injected with M=1.53 at the geometry condition of L/d=23.8.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.1
• /
• pp.1-22
• /
• 2012

This paper tried to verify whether the fixed fire fighting system (FFFS) that is installed in road tunnel improves evacuation performance or not. Verification was performed according to the Disaster Prevention Facilities Installation and Management Guide at Road Tunnel. Twenty seven different fire scenarios were set up for the verification and the cases that FFFS was installed were compared with the cases that FFFS was not installed. The result of the comparison showed that the average equivalent death was reduced in 26 cases out of 27 cases when water spray extinguishing system was installed. It was confirmed that the risk when was not installed was unacceptable in Hong Kong and the Netherlands. On the other hand, it was confirmed that the risk was reduced to as low as reasonably practicable (ALARP) when was installed. The cumulative frequency of average death in case with FFFS was compared against the frequency of death without FFFS: death of one or more is about 50 times less; 10 or more is about 100 times less; and the death of more than 100 is four times less. It was verified that FFFS makes improved conditions to escape from the fires in road tunnel.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.53-59
• /
• 2011

The using of diesel engine will be increased in the world for fuel economy. But diesel engine emits harmful emissions such as much NOx, smoke etc. In this study, experiments were performed to investigate the spray characteristics of diesel spray in a common-rail system according to fuel temperature, injection pressure, injection period and fuel viscosity etc. using a high speed video camera. Diesel oil has different spray patten due to injection pressure and injection period in a common-rail system. A Filter pressure was influenced by fuel temperature which was turned to fuel viscosity related to a fluid flowing. The effect of the bio-diesel fuel mixing ratio on the spray and atomization characteristics was also investigated at various experimental conditions. It shows that the droplet atomization characteristics of bio-diesel fuel showed deteriorated results as the mixing ratio of biodiesel increased because of the high viscosity.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.495-501
• /
• 2012

Spray characteristics of liquid jets in crossflow, which can be observed in the liquid jet injection system of a gas turbine or ramjet engine, were experimentally investigated. By measuring liquid jet penetration in the case of single orifice and double orifice injectors, the experimental formula for jet penetration was modified to consider penetration distances greater than that considered in a previous study. The changes in spray characteristics resulting from changes in the liquid jet and crossflow pressure, including SMD and jet disintegration, were carefully studied. Specifically, the jet penetration was measured for different injector shapes, and in the case of a double orifice injector, the penetration of the rear orifice jet was found to be greater by approximately 20% ($L_h$ = 4 mm) compared to that in the case of a single orifice injector because of the influence of the front orifice.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2015.10a
• /
• pp.77-78
• /
• 2015

산업화로 인하여 토지의 사막화, 물부족, 오존층 파괴, 지구 온난화 등 많은 환경문제가 발생되었으며 아직 진행 중에 있다. 이에 UN에서는 환경 규제를 강화하였으며 국제해사기구(IMO:International Maritime Organization)에서는 선박의 배기가스 규제 강화를 위하여 NOx(질소산화물) 및 SOx(황산화물)의 배기량을 줄이도록 하고 있으며 2016년부터는 본격적으로 규제하려 하고 있다. 상기의 규제 물질 중 NOx를 제거하는 선택적환원촉매(SCR:Selectivity Catalytic Reduction) 시스템은 선박의 배기가스가 지나가는 통로에 요소수(Urea)를 분무하여 $260^{\circ}C$ 이상의 높은 온도에서 요소수에 있는 암모니아가 배기가스에 있는 NOx와 반응, 결합함으로서 NOx를 질소와 산소로 분리, 제거하는 방식이다. 하지만 선박의 경우 대부분 엔진이 2행정으로 배기가스 온도가 일반적으로 $180^{\circ}C{\sim}220^{\circ}C$이기 때문에 요소수에 있는 암모니아가 배기가스에 있는 NOx와 반응하지 않아 환원률이 높지 않다. 이에 우리는 초미세기포를 이용하여 낮은 온도에서도 반응할 수 있는 요소수 및 요소수 활성화 기기를 개발하여 상기의 문제점들을 최소화 할 수 있도록 하였다. 또한 SCR 시스템의 점성유동해석을 통하여 보다 효율적인 SCR 시스템의 개발을 할 수 있도록 기여하였다.

• Journal of ILASS-Korea
• /
• v.2 no.4
• /
• pp.7-14
• /
• 1997

Laser Raman scattering method has been applied to measure equivalence ratio of methane/air mixture in injected spray. We used high power KrF excimer laser$(\lambda=248nm)$ and a high gain ICCD camera to capture low intensity signal. Raman shifts and Raman scattering cross -sections of $H_2,\;O_2,\;N_2,\;CO_2,\;CH_4\;and\;C_3H_8$ are measured precisely. Our results show an excellent agreement with those of other groups. Mole fraction measurement of $O_2\;and\;N_2$ from air shows that $O_2:N_2=0.206:0.794$. We used gas injector which was operated at 1 bar. Methane is used as a fuel. Spray region is $10mm\times37mm$ and this region is divided into 80 points. In Raman signals are obtained and ensemble averaged for each point. 3-d and contour plot of distribution of equuivalence ratio is presented. Our measured results show that the equivalence ratio of methane/air mixture in methane-rich region is reasonable. However, more study is necessary for methane-lean region because background noise level is almost same as Raman intensity of methane.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.3 s.14
• /
• pp.83-87
• /
• 2004

In underground culvert are established main and basic facilities for electric power, communication, gas and heating pipe etc. In the future the use of underground culvert will be enlarged and the peril of fire will be increased. Thus it is necessary to make a general plan to prevent fire. The skills to prevent fire in underground culvert will be accumulated by the spray distribution of the nozzle and domestic skills in fire fighting will be upgraded. It will also contribute to the construction of common small fire fighting system suitable to the domestic surrounding and the growth of domestic skills for fire fighting and disaster prevention.

• Journal of ILASS-Korea
• /
• v.24 no.3
• /
• pp.105-113
• /
• 2019

In this paper, a study of Urea-SCR System for Dosing Injector for responding to enhanced environmental regulations has been conducted. There is a limit to the experimental approach due to the structural characteristics of the injector. In order to overcome this problem, The analysis was performed assuming unsteady turbulent flow through computational fluid analysis and the internal flow characteristics of the injector were analyzed. By changing the nozzle shape of the injector, the performance factors of the swirl injector by shape were selected and compared. The design parameters were modified by changing the diameter of the nozzle at a constant ratio compared to the base model. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. The Conv. model to which the taper was applied showed the dominance in mass flow rate, discharge coefficient and swirl because of the smooth fluid flow by shape. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. As a result of the comparison coefficient derivation with those performance parameters for comparing the performance of the model-specific injector, the Conv-140 model with the nozzle diameter expanded by 140% showed the best value of the comparison coefficient.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.4-4
• /
• 2000

일반적인 액체추진제 로켓엔진의 연소는 분사제트의 미립화, 액적의 증발, 기상 추진제의 혼합, 화학반응 등, 일련의 물리적 과정들로 이루어지고, 여기서 특성속도 효율은 크게 분사특성 및 연소의 두 단계에서 결정되게 된다. 액체추진제 로켓엔진에 사용되는 여러 분무형태 중, 동축형 분사기에서는 액상과 기상 제트의 운동량 차에 의해 미립화가 이루어지며, 분무 액적들의 전개와 더불어 분사기 출구를 포함한 전 영역에서 연소가 발생되므로 매우 복잡한 물리적 특성들을 포함하게 된다. 본 연구에서는 기상 연료-액상 산화제의 동축형 분무연소를 JANNAF의 방법을 사용하여 수식화 하였으며, 이를 바탕으로 분무특성과 연소성능 예측을 위한 프로그램을 작성, 분사조건에 의한 분무특성과 그에 따른 연소성능을 계산하였다. 연속, 운동량, 에너지 및 혼합비 방정식의 지배방정식들을 바탕으로 기상 유동을 수식화 하였으며, 별도로 액적의 소산 및 연소과정을 모사하기 위한 별도의 수식들이 추가되었고, 이 식들을 결합하여 액적의 크기, 분포를 포함하는 액체 제트의 미립화 정도를 공간적으로 계산하였다. 미립화 모델의 검증을 위하여 계산 결과를 Reitz의 실험과 Giridharan의 모델 등과 비교하였으며 잘 일치하는 경향을 나타내었다. 또한 동축형 분사기에서의 분무 특성을 예측하기 위해 액체 산소, 기체 수소를 추진제 조합으로 하는 동축형 분무 연소장에서의 제트 길이, 액적의 크기, 액체 제트의 속도를 계산하였다. 계산 결과 액체 제트의 접촉길이는 분사공의 지름이 증가할수록 웨버수가 증가되므로 짧아지는 것으로 관찰되었으며 액적의 크기도 분사공의 지름이 증가할수록 작아지는 경향을 나타내었다. 액체 제트의 속도는 처음에는 일정하게 유지되다가 운동량을 보존하기 위해 가스로부터 운동량을 받아 점차 가속되어지는 것으로 나타났다.본 규격은 키, 총장, 어깨길이, 등길이, 머리길이, 머리둘레, 진동둘레, 목둘레, 가슴둘레, 허리둘레, 배둘레, 엉덩이둘레, 앞품, 뒤품, drop치를 포함하고 있고, 각 규격에서 호칭간 치수 간격도 함께 제시하고 있다. 본 연구 결과에서 보듯, 현행 8규격의 무진복의 각 호칭간 적정 허용범위를 고려해 합리적인 치수체계를 정립한다면 치수에 대한 적합도가 상당히 증가할 뿐 아니라 생산비용도 상당히 감축할 것으로 생각된다.나타났다. 4) 호감적 서비스능력 차원에서 세 독립변수간에 유의한 3원 상호작용이 존재하는 것으로 나타나( $F_{2,228}$=15.62, P<.001) 20대에 적합한 의복 착용시( $F_{2,228}$=3.98, P<.05)와 60대에 적합한 의복 착용시( $F_{2,228}$=16.55, P<.001) 점포유형과 격식차림간에는 유의한 상호작용이 존재하는 것으로 나타났다. 5) 호감을 구성하는 세 요인들이 구매의도에 미치는 영향을 조사한 결과 호감적 인상차원은 29%(P<.001), 호감적 서비스능력차원은 6%(P<.001)의 구매의도를 설명해 주는 것으로 나타났다. 본 연구결과 노년 소비자에게 호감을 주는 판매원의 외모는 구매의도에 영향을 주어 실버의류산업의 이익증대와 밀접한 연관을 갖는 서비스품질의 중요한 요인으로 밝혀졌다.중요한 요인으로 밝혀졌다.로운 단백질 EPSPS가 다른 여러 식물에 이미 존재하고 있는 단백질로서 우리가 이미 이러한 식품을 섭취할 때 이 단백질도 같이 섭취해오고 있었다는 점, 둘째. 이 단백질이 소화액 분해 실험에서 짧은 시간내에 분해가 되었다는 점, 셋째. 재조합 된 콩과 자연 콩이 성분 분석에서 차이를 나타내지 않았다는 점, 네 번째. 쥐를 통한 다양섭취 실험에서 아무런 이상 반응이 없었