• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.28-33
• /
• 2020

In this study the possibility of hydrogen as a fuel in a small-sized two-stroke SI (Spark ignition) engine was investigated. For this purpose, experimental setup including an engine, a dynamometer, equipments for hydrogen and lubricant oil supply was prepared. And then preliminary experiments for the hydrogen-fueled engine combustion were conducted. In the case of hydrogen-fueled engines comparing to gasoline backfire occurs when the excess air ratio is lower than a specific value. This can cause engine power reduction and damage to the engine parts. The engine was controlled to operate at lean conditions to prevent backfire. Through the control of excess air ratio, the maximum engine brake power output of 3 kW was achieved in a 210 cc engine, while it was 6 kW in case of gasoline fuel.

• Journal of the Korean Society of Industry Convergence
• /
• v.1 no.1
• /
• pp.31-41
• /
• 1998

Fuel conservation and environmental pollution control are the principal motivating factors that are urging at present widespread research and development activities for electric hybrid vehicles throughout the world. The paper describes different possible energy storage devices, such as battery, flywheel and ultra capacitor, and power sources, such as gasoline engine, diesel engine, gas turbine and fuel cell for next generation hybrid electric vehicle. The technology trend and comparison in energy storage and power devices indicate that battery and gasoline engine, respectively will remain the most viable devices for hybrid vehicle at least in the near future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5082-5088
• /
• 2015

In this paper, durability test of 1000cc level gasoline engine has been carried out. Durability test set total 300 hours and WOT condition. Engine torque, power, fuel consumption, blow-by gas flow rate, and oil pressure are measured to analyse performance variation by time. As a result, engine performance of high rpm range gradually reduced by time but for relatively low rpm range shows stable performance. Blow-by gas flow rate shows 0.4% of averaged induction air flow rate, which is excellent rate for 1000cc level gasoline engine. Engine torque and fuel consumption data show the break-in upto 100 hours and aging trend after that. After 300 hours, engine is disassembled and each part is checked for the damage or crack.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.16-27
• /
• 1986

In this study, low emission gasoline engine system is developed utilizing an EGR valve, 3 way catalytic converter and electronic fuel injection system. EGR was controlled by a needle valve and optimized at the engine conditions. Throttle body fuel injection system is used for fueling. When the engine was operated at constant speed by the electronic engine control system with the 3 way catalytic converter, th emissions were reduced by 50 to 90% in volume depending on he engine operating conditions.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.3
• /
• pp.109-115
• /
• 2008

A burning principle in gasoline engine is the one of being burned, by which a mixer in air and gasoline enters a combustion chamber and causes a spark in the proper timing. This is formed, by which ECU controls the fuel-injection volume and the fuel-injection timing, and determines the performance of engine. The purpose of this study is to test the characteristics on knocking in gasoline engine with the knocking-sensor equipment and to research into the characteristics in knocking while directly controling the optimal igniting timing and the fuel-injection timing through engine ECU. Given controlling ECU by grasping the characteristics in knocking, which becomes the most problem in the engine tuning market, the tuning in a true sense will be formed in gasoline engine.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.131-137
• /
• 2012

This article is about using the fuel mixed with 10% and 20% bio-ethanol to gasoline for the engine as a way to reduce carbon emission before commercializing future automobiles like fuel cell cars. The fuel mixed with 10% and 20% bio-ethanol showed output equivalent to that of the previous gasoline fuel. CO and $CO_2$ emission was somewhat reduced, but the difference was not significant. And the consumption of the fuel increased slightly. However, bio-ethanol is produced from bio mass growing with the absorption of carbon dioxide, so the total amount of carbon dioxide did not increase according to the result. In NOx, as the use of ethanol increases, the effect of reduction gets greater, and the emission of oxygen showed almost no change compared with gasoline.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.34-39
• /
• 2015

Recently, most of the energy consumed in vehicle is derived from fossil fuels. For this reason, the demand for clean, renewable and affordable alternative energy is forcing the automotive industry to look beyond the conventional fossil fuels. Natural gas represents today a promising alternative to conventional fuels for vehicles propulsion, because it is characterized by a relatively low cost, better geopolitical distribution than oil, lower environmental impact, higher octane number and a higher self ignition temperature. Above all, CNG is an environmentally clean alternative to the existing spark ignition engines with the advantages of minimum change. In this study was installed bi-fuel system that a conventional 2 liters gasoline engine was modified to run on natural gas by a gas injection system. Experiments were mainly carried on the optimization of an ECU control strategy affecting the emission characteristics of CNG/Gasoline bi-fule vehicle. The test results shown that CO2 emission in bi-fuel mode was reduced 16% compared to gasoline fuel in the NEDC mode. Also the amount of CO and HC emissions in bi-fuel and gasoline modes were found to equality. But Compared to gasoline, the bi-fuel mode resulted in higher NOx emissions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.96-101
• /
• 2005

Cogeneration is an energy conversion process, where electricity and useful heat are produced simultaneously in one process. Also, carbon dioxide emissions can be reduced as well. The cogeneration process may be based on the use of steam, gas turbines or combustion engines. However, there have been few models with an output of less than 100 kilowatt. In the present study, a spark ignited gas engine with generation output of 10 kilowatts was developed for micro cogeneration package. The gas engine shows 29.2$\%$ of thermal efficiency under Stoichiometric combustion and 33.6$\%$ of thermal efficiency under lean combustion. NOx emission shows less than 10ppm at 13$\%$ oxygen under stoichiometric combustion and about 100ppm at 13$\%$ oxygen under lean combustion.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.1-8
• /
• 2002

Metal surface temperatures around the combustion chamber in a gasoline engine directly affect thermal durability and performance of the engine. Metal surface temperatures are influenced by many cooling factors such as drilled water passage, deflector, combustion chamber wall thickness, pillar, and coolant flow pattern. The object of this study is to learn how the coolant passages and coolant flow pattern in an engine influence to the engine metal surface temperature at engine full load and speed. From the test result, it is suggested a plan to reinforce the engine stiffness and to reduce the thermal stress simultaneously. Also, approaches are introduced to reduce the thermal load on the engine by adjusting the discharging direction from the water pump and by optimizing the water transfer holes in the cylinder head gasket. These methods and the optimized engine cooling system, which were suggested in this paper, were adapted for an engine in progress to eliminate the exhaust valve seat wear.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.82-89
• /
• 2011

Ultra lean combustion with stratified air-fuel mixture is one of the methods that can improve fuel economy of gasoline engines. The aim of this study is to show that how much fuel economy is improved and what are differences in engine control of the ultra lean combustion compared with stoichiometric combustion. In this study, the BMW N53 GDI engine, which is one of ultra lean combustion GDI engines introduced in the market recently, was tested at various engine operating conditions. Results indicated that fuel consumption rates were improved by 11.9~25.8% by the ultra lean combustion compared with stoichiometric combustion. It was also found that multiple fuel injection, multiple spark, early intake valve opening, and large vlave overlap duration were the features of the ultra lean combustion for combustion stability and emission improvement.