• The Journal of the Acoustical Society of Korea
• /
• v.11 no.4
• /
• pp.31-35
• /
• 1992

Cavity resonances are caused by combustion such as the rapid of pressure rise that occurs from knock in high power gasoline engines. These resonances generally occur at frequencies greater than 5KHz. Analysis of these resonances is important for knock control system design in high power gasoline engines. In this paper, in order to design knock control system for the high power gasoline engine, knock phenomena that occur in chamber were analized theoretically and resonance frequencies of knock signals were predicted. Also, experiments were performed using Soupe x-engine and non-resonance type knock sensor of Bosch co. in Germany. In the result, good agreement was obtained between theoretical prediction and experimental observation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1371-1379
• /
• 2012

This paper presents a method for estimating the contribution of vibration sources in gasoline direct injection engine parts with a multiple-input system. A partial coherence function was used to identify the cause of the linear dependence indicated by an ordinary coherence function. To apply the partial coherence function to vibration source identification in the powertrain system of a gasoline direct injection engine, a virtual model of a two-input and single-output system is simulated. For the validation of this model, the vibration of the powertrain parts was measured by using triaxial accelerometers attached to the selected vibration sources-a high-pressure pump, fuel rail, injector, and pressure sensor. After calculating the partial coherence between each source based on the virtual model, the vibration contribution of the powertrain system is calculated. This virtual model based on the partial coherence function is implemented to determine the quantitative vibration contribution of each powertrain part.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.63-70
• /
• 1998

According to the stringent exhaust emission regulation control of air fuel ratio is one of the most important issues on gasoline engine. Although many researches have been carried out to identify the fuel transport phenomena in a port fueled gasoline engine, complexity of fuel film behavior in the intake port makes it difficult. The fuel film behavior was investigated recently by using visualization method and these gave us qualitative understanding. In this paper, the quantitative measurement method for the port fuel film is studied by using Fast Response Flame Ionization Detector(FRFID). The mass of fuel film on the port wall was measured by using the methods of fuel injection off, injection on and regression. The Fuel film mass was increased with incresing load at the same engine speed.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.242-247
• /
• 2018

The automotive industry is making various efforts to cope with ever-increasing exhaust emissions and fuel economy regulations. However, this often results in degraded NVH (Noise, Vibration, and Harshness) performance. For example, we proposed the causes and improvements for the noise generated by the high-pressure pump noise of a gasoline engine, the change of acceleration noise due to dual injection of MPI (Multi-Point Injection) and GDI (Gasoline Direct Injection), the noise of a gasoline turbocharger, and the combustion noise deteriorated due to the injection parameters calibration in a diesel engine. Since these noises are caused by the high frequency noise, and the driver feels the rough sound quality, efforts to reduce them with proper NVH measures are indispensable.

• 연구논문집
• /
• s.23
• /
• pp.63-71
• /
• 1993

To improve flow in-cylinder flow in a 2-valve gasoline engine, various geometries of combustion chambers are modified. Air flow rate, swirl and tumble flow are measured and analyzed by swirl impulse meter and LDV in a steady state flow measuring rig. The results of LDV experiment are compared with the data of swirl impulse meter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.41-42
• /
• 2006

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.48-55
• /
• 2003

The effects of pressure charge on combustion stability and emissions have been analyzed using a GDI single cylinder engine. A late injection mode of stratified condition at the air-fuel ratio of 40:1 for 1200∼2400 rpm was tested while the boosted pressure ratio was increased up to 1.5:1. In-cylinder CFD analysis was also performed for better understanding of in-cylinder flow and fuel spray behavior. With a higher boosted pressure ratio the IMEP was increased greatly due to the increased engine load, and the ISFC was improved by more than 10% at all engine speeds. The regime of stable stratified combustion was extended to a higher engine speed, but the spark ignition angle had to be more advanced for stable combustion. The emissions of ISHC and ISNOx did not show a particular trend for the increased engine speed but a general trend of lower ISHC and higher ISNOx for a gasoline engine.

• Journal of ILASS-Korea
• /
• v.9 no.2
• /
• pp.9-17
• /
• 2004

The performance characteristics of lean burn system in gasoline engine are mainly affected by the air-fuel mixture in cylinder, gas exchange process of manifold system, exhaust emission of engine, and the electronic engine control system. In order to obtain the effect of performance factors on the optimum conditions of lean burn engine, this study deal with the behavior of mixture formation, gas flow characteristics of air, flow and evaporation analysis of spray droplet in cylinder, vaporization and burning characteristics of lean mixture in the engine, and the control performance of electronic engine control system. The optimum flow conditions were investigated with the swirl and tumble flows in the combustion chamber with swirl control valve. The performance characteristics and optimum condition of flow field in intake system were analyzed by the investigation of inlet flow of air and combustion stabilization on cylinder.

• Journal of ILASS-Korea
• /
• v.27 no.3
• /
• pp.161-166
• /
• 2022

To measure the change in friction loss due to the control of fuel mass and oil temperature in a gasoline engine, the floating liner method was used to measure the friction generated by the piston of a single-cylinder engine. First, to check the effect of combustion pressure on friction, the friction loss was measured by adjusting the fuel mass. It was confirmed that the friction loss increased as the fuel mass increased under the same lubrication conditions. In addition, it was confirmed that the mechanical efficiency decreased as the fuel mass increased. Next, to check the effect of lubrication conditions on friction, the friction loss was measured by controlling the oil temperature. It was confirmed that friction loss increased as the oil temperature decreased at the same fuel mass. As the oil temperature decreases, the viscosity increases, resulting in decreased mechanical efficiency and increased friction loss.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.65-71
• /
• 1999

Recently new engine system is being required to cope with intensive emission restriction . For this reason, GDI(Gasoline direct injection) engine system which can satisfy both as good fuel economy as diesel engine and the performance to surpass PFI gasoline engine is being development . Since fuel injection system plays a significant role in GDI engine performance, the investigation of the spray characteristics injected from GDI injector above all is indispensable for GDI system development. In this study , spray developing shape was visualized using laser sheet with Nd : YAG laser and atomization characteristics was analyzed by measuring velocities and droplet size with PDA. Utilizing these results , the basic design factor of GDI injector can be offered.