• Journal of the Korean Geotechnical Society
• /
• v.26 no.5
• /
• pp.15-26
• /
• 2010

This paper presents the results of a three-dimensional finite element analysis on a geosynthetic-reinforced bridge abutment. Examples on the use of mechanically stabilized earth bridge abutment in north America are first presented. A three-dimensional finite element analysis on a 4.8 m high, 14 m wide geosynthetic-reinforced bridge abutment was performed to investigate the 3D behavior of the geosynthetic-reinforced bridge abutment and the load carrying capacity of the bridge abutment in the three-dimensional space. The results are then presented in a way that the three-dimensional behavior of the abutment can be identified in terms of wall displacements and reinforcement forces. It is shown that the wall facing displacements as well as the reinforcement forces in the abutment are smaller than those computed based on a plane strain approximation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.4
• /
• pp.487-496
• /
• 2021

Full mouth rehabilitation is re-organizing the occlusion of the remaining teeth and missing teeth considering the functions, esthetics, and neuromuscular harmony. With the loss of multiple teeth, the patient's occlusal plane gradually collapses and the vertical dimension can be reduced. Since reduced vertical dimension can be a potential etiology of the temporomandibular joint and masticatory muscles, prosthetic restoration with increased vertical dimension is required. This case report is about a 68 years old patient with vertical dimension loss due to worn dentition and multiple loss of teeth. In this case, the loss of vertical dimension is assessed carefully using the digital dentistry technology. Using CAD software in digital analysis step, the occlusal plane was established and evaluated using several criteria. Orienting the position of the bone and teeth using CBCT image, patient's condition was visualized in 3 dimension and treatment planning was possible virtually. The information that matches the patient's condylar position with the articulator, which is the virtual face bow, is reproduced on the actual articulator, and evaluated again. After the evaluation, provisional prosthesis was fabricated and it was confirmed that the patient adapts without any abnormality. This was implemented as a final prosthesis. As a result, the patient obtained satisfying results, utilizing the benefits of digital dentistry technology and traditional methods.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.6
• /
• pp.354-362
• /
• 2006

This paper suggests a method for generating high qualify stereo video avatar to support visual communication in a CAVE$^{TM}$-like system. In such a system because of frequent change of light projected onto screens around user, it is not easy to extract user silhouette robustly, which is an essential step to generate a video avatar. In this study, we use an infrared reflective image acquired by a grayscale camera with a longpass filter so that the change of visible light on a screen is blocked to extract robust user silhouette. In addition, using two color cameras positioned at a distance of a binocular disparity of human eyes, we acquire two stereo images of the user for fast generation and stereoscopic display of a high quality video avatar without 3D reconstruction. We also suggest a fitting algorithm of a silhouette mask on an infrared reflective image into an acquired color image to remove background. Generated stereo images of a video avatar are texture mapped into a plane in virtual world and can be displayed in stereoscopic using frame sequential stereo method. Suggested method have advantages that it generates high quality video avatar taster than 3D approach and it gives stereoscopic feeling to a user 2D based approach can not provide.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.5
• /
• pp.52-60
• /
• 2005

The conceptual model of under-sampled study area will include a great amount of uncertainty. In this study, we investigate the applicability of Markov chain model in a spatial domain as a tool for minimizing the uncertainty arose from the lack of data. A new formulation is developed to generalize the previous two-dimensional coupled Markov chain model, which has more versatility to fit any computational sequence. Furthermore, the computational algorithm is improved to utilize more conditioning information and reduce the artifacts, such as the artificial parcel inclination, caused by sequential computation. A generalized 20 coupled Markov chain (GCMC) is tested through applying a hypothetical soil map to evaluate the appropriateness as a substituting model for conventional geostatistical models. Comparing to sequential indicator model (SIS), the simulation results from GCMC shows lower entropy at the boundaries of indicators which is closer to real soil maps. For under-sampled indicators, however, GCMC under-estimates the presence of the indicators, which is a common aspect of all other geostatistical models. To improve this under-estimation, further study on data fusion (or assimilation) inclusion in the GCMC is required.

• Archives of design research
• /
• no.18
• /
• pp.25-34
• /
• 1996

Industrial design development methods and processes have changed in accordance with Industrial Information Age. These days, problems are created by existing methods and evaluation of design value , all problems concerned with time and finances sitaution have been made a subject of discussion. Development of design processes have been changed by the development of problem recognition and solving tools, and dpsign tpchnulugy havp hppn replaced by computer technology,Thus. software design processes linking thoughtware to hardware are used in the solution of design problems with many parts. In this study, 3D Modeling samples are presented, 3D Modeling can realise ' Ideas' to '3Dimentional Virtual Ohjects'. These effect and value are anle to decisively influence the process of design problem conference-ebealuation-solution.Proxesses of actual modeling and rendering are made as follows. By compusition of simple 20 drawings and shaping them into 30 objects, 30 solid models can be made. To prssent effectivley, we can make a sample model by varying camera views,light sourses,materials and colours etc. This sample is evaluated by various cumposition, methods and PERT(Program Evaluation and Review Technique). This cuncrete sample (tentative plan)is changed within the CAD SYSTEM by design evaluation, and then converted to flowchart of mass productive conception through refined data. So, that tentative plan can be conformed to design desire actuillly, to the utmost degree. Finally, this design process can be proposed as il new method in cuntrast with current methods. The aim of this study is to suggest effective evaluation methods of design outcome among many evaluating elements.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.197-204
• /
• 2013

A method was developed for analyzing the radiation heat transfer from the duct burner flame to the heat exchanger in a heat recovery steam generator (HRSG) in order to supplement the existing thermal design process. The burner flame and the heat exchanger were considered to be imaginary planes, and the flame temperature, surface, and emissivity were simplified using an engineering approach. Three analysis cases in which the duct burner position and fuel were changed were considered. The calculated flame radiative heat transfer and local flux on the heating surface were compared with those of 3-atomic gas radiation and convection. In all analysis cases, heat transfer by 3-atomic gas radiation was very small. The ratio of the flame radiative heat transfer to the convection heat transfer on the heating surface was estimated to be as high as 8-41%. Moreover, the local heat flux on the heating surface centerline was dominated by flame radiative heat flux.

• Korean Journal of Optics and Photonics
• /
• v.18 no.6
• /
• pp.432-440
• /
• 2007

Optical simulation methods such as a ray tracing technique have been widely used to predict the optical performances of collimating films for LCD backlight applications. It is necessary to optimize simulation conditions which have substantial effect on the simulation result in order to predict accurate performances of collimating films. We have set up a very simple backlight model consisting of a reflection film, a virtual flat light-source, and a prism film, which is a representative collimating film for backlight, in order to analyze the simulation conditions which are strongly correlated with the on-axis luminance gain and the viewing-angle characteristics of prism films. It was found that the dependence of the relative change in the on-axis luminance on the structure and material properties of collimating films can be derived from the above-mentioned simple BLU model and from simulation using it. However, the exact reflection property of the reflection film and the distribution of the incident light onto the optical film were found to be very important for revealing exact viewing-angle characteristics of collimating films.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.2
• /
• pp.33-40
• /
• 2014

At present, Cadastral map of 2 dimensional is in the stream of changing it to 3 dimensional type supported by GPS and laser techniques. In addition, this steam can be explained at the same time with improvement of equipment of storing much information, support of equipment for imaginative 3D spatial information, and support of equipment of expressing land in 3D Cadastral. This study suggest to apply airborne lidar survey technique on cadastral map to acquire comparably and quickly detailed height of ground. For doing this, this study checked out credibility regarding accuracy of airborne lider survey. After choosing research area, this study has done the airborne lidar survey and acquire the result after surveying Cadastral Comparison Point to check out the accuracy of acquired results. In addition, this study check out the result of Cadastral Comparison Point and airborne lidar survey applied by paired sample t-test based on actual results. The result is that test statistics is 0.322 which is 5 % similar level and null hypothesis cannot be rejected, so this study found out that result of both survey ways are the same. Therefore, the result of airborne lidar survey can be utilized to build up 3D Cadastral information hereafter.

• 한국지구과학회:학술대회논문집
• /
• 2010.04a
• /
• pp.48-50
• /
• 2010

Stommel(1948)은 서안경계류의 원인이 베타효과($\beta$-effect)라 일컫는 코리올리 파라미터(f)의 위도 변화 때문인 것을 밝혔다. 서안경계류는 고등학교나 대학 교양에서 중요하게 다뤄지고 있다. 학생들은 보통 이론 수업만으로 서안경계류의 발생 과정, 이에 관련된 코리올리 힘, 베타효과 등을 이해해야 한다. 때문에 서안경계류와 관련된 실험이 있다면 이를 이해하는 데 큰 도움이 될 것이다. 또한 연구에서 검토한 6종의 고등학교 지구과학 2 교과서는 서안경계류를 본문과 더불어 삽화로 설명하고 있다. 그러나 이 중 3종의 교과서 삽화에서는 서안경계류의 발생 원인을 코리올리 힘만으로 지적하고 있다. 따라서 일부 학생은 서안경계류의 원인을 코리올리 힘으로 오해 할 수 있다. 위와 같은 이유로 우리는 서안경계류가 코리올리 힘의 작용과 베타효과에 의해 나타나는 것을 쉽게 확인 할 수 있는 실험 장치와 다양한 실험 방법을 개발하였다. 개발한 실험 장치는 직육면체의 수조와 회전 속도를 조절할 수 있는 테이블로 구성된다. (Fig. 1) 이와 같은 회전수조는 대기와 해양의 움직임을 실험실에서 모사하기 위해 자주 사용되었다(Beardsely 1969, 소선섭 등 1995; 1997). 우리의 수조는 경사진 바닥과 평평한 바닥으로 두종류를 제작하였다. 바닥이 경사진 수조는 베타효과를 구현하기 위한 것이다. 반시계 방향으로 회전하는 테이블은 중위도 어떤 위도에 접하는 가상의 평면이 지구 자전에 의해 회전하는 것을 나타낸다. 그리고 수조 상부에는 회전원판을 물에 접하여 시계방향으로 회전시킨다. 회전원판은 북반구 중위도 해양에 작용하는 바람 응력을 나타낸다. 우리는 테이블의 회전유무와 바닥의 경사유무에 따라 4개 실험을 수행하였다(Table. 1). 각 실험에서 물을 채운 수조를 원판에 올려놓고, 회전원판을 작동시킨 후 20분 동안 그대로 두어 수조안의 미세규모의 운동을 최소화 시킨 후 잉크를 떨어뜨리고 관찰하였다. 그 결과 실험 SB_f1은 베타효과와 코리올리 힘이 존재하여 서쪽 경계에서 좁고 빠른 흐름을 만들고 수조의 중간 부근에서 경계를 벗어나 동쪽으로 향하고 있다. 이 모습은 실제 해양의 서안경계류의 분리 현상과 비슷하다. FB_f1은 코리올리 힘만 존재하여 서쪽 경계에서 좁고 빠른 순환과 경계를 벗어나 동쪽으로 분리되는 흐름이 나타나지 않으며 전반적으로 크게 회전하는 모습을 보인다. SB_f0은 바람의 응력만 존재하는 경우로 잉크가 확산하는 모습을 보이며 나선팔의 모양으로 회전하면서 넓게 퍼져나간다. FB_f0의 모양도 이와 비슷하게 나타난다. 실험 SB_f1과 FB_f1을 비교하여 서안경계류는 코리올리 힘의 위도변화 효과인 베타효과가 있을 때 발생한다는 것을 알 수 있다(Fig. 2). 이 결과는 "단순히 코리올리 효과에 의해 서안경계류가 발생한다"는 생각을 바꾸게 할 것이다. 덧붙여 서안경계류 분리와 수조 바닥의 경사의 관계를 살펴보기 위한 실험을 실시하였다. 경사가 더 급하면 ($\alpha=20^{\circ}$) 서쪽 경계를 벗어나는 지점이 좀 더 북쪽에 나타났다. 현재 서안경계류는 개발한 실험 장치와 방법을 학교 현장에 적용하여 그 교육적 활용 가치를 평가하는 연구를 진행하고 있다.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.6
• /
• pp.183-191
• /
• 2020

In this study, in order to obtain basic data on the development of a new hanbok skirt pattern for developing a customizing system, a new hanbok brand skirt pattern was compared and analyzed. After analyzing the patterns of six new hanbok brands, virtual simulation was performed to evaluate the appearance, clothing pressure, and airgap. As a result of analyzing the waist skirt patterns of commercial new hanbok brands A, B, C, D, E, and F, it was found that they were produced in different dimensions despite the free size skirt of the same design. The pattern of new hanbok waist skirt was composed of a flat pattern like the traditional hanbok. As a result of appearance evaluation, it was evaluated that there were significant differences between the patterns of the six brands in all the evaluation items on the front, side, and back. In the appearance evaluation, it was evaluated that the waist skirt of the B brand was excellent. As a result of examining the color distribution and airgap, it was evaluated that the airgap was large in most parts due to the characteristics of the waist skirt worn around the waist, and the garment pressure was low. In this paper, we propose a basic data for standardizing dimensions and patterns according to activation New Hanbok. It is thought that a unified pattern development based on the B brand pattern should be made.