• Journal of Korea Water Resources Association
• /
• v.48 no.9
• /
• pp.729-741
• /
• 2015

This study examined the applicability of MBLRP (Modified Bartlett-Lewis Rectangular Pulse) rainfall generation model for an urban flood simulation which is a type of Poisson cluster rainfall generation model. This study constructed XP-SWMM model for Namgajwa area of Hongjecheon basin, which is a two-dimensional pipe network-surface flood simulation program and computed a flood discharge and a flooded area with input data of synthetic rainfall time series of 200 years that were generated by the MBLRP model. This study compared the data of flood with synthetic rainfall and flood with corresponding values which were based on design rainfall. The results showed that the flooded area computed with MBLRP model was somewhat smaller than the corresponding values on the basis of the design. A degree of underestimation was from 8% (5 year) to 34% (200 year) and the degree of underestimation increased as a return period increased. This study is meaningful in that it proposes methodology that enables quantifiability of uncertain variables which are related to a flooding through Monte Carlo analysis of urban flooding simulation and applicability and limitations thereof.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.248-252
• /
• 2010

홍수기 호우로 인한 피해는 대부분 하천구역에서 발생되며, 이러한 피해는 인간에게 직 간접적으로 영향을 미치게 된다. 자연 상태의 하천형상은 대부분 호우로 인한 홍수로 인해 자연스럽게 만들어지게 되며, 대부분 사행하천의 형태를 띠게 된다. 사행하천에서의 흐름의 기하학적 특성은 성장이나 사멸, 또는 두 가지 모두의 형태를 보인다. 사행하천에서의 흐름 및 유속 분포는 하천제방 보호, 주운, 취수, 그리고 유사 이동 및 퇴적 패턴과 관련하여 실용적인 관점에서 연구하여야 하는 하천수리학에서는 매우 중요한 주제이다. 그리고 사행하천은 특히 만곡부가 교호적으로 나타나는 곳에서의 흐름구조가 매우 복잡하다. 이러한 사행하천에서는 회전방향이 교호적으로 바뀌는 나선형의 흐름(2차류)이 3차원적으로 발생하는 것으로 알려져 있다. 본 연구에서는 사행하천이 많은 국내 하천특성을 고려하여, 하천 만곡부에서의 흐름특성을 분석하고자 하였으며 2차원 CCHE2D 와 3차원 FLOW3D 모형을 적용하였으며 가상 하도에 대하여 수리모형 실험의 실측치와 비교하여 모형의 정확성과 안정성을 검증하였다. 그리고 남강댐 하류에 대하여 만곡부의 흐름특성(유속 분포 및 최대유속경로, 수위분포, 2차류 거동, 편수위, 전단응력 분포 등)을 분석함으로써, 하천 만곡부에서의 수리적 특성을 보다 정확하게 제시하고자 한다. 모의 분석결과 동일 하도에 대하여 유량을 변동시킬 경우, 유량이 증가할수록 만곡부에서의 수리영향이 더욱 뚜렷해짐을 알 수 있었고 2차원 모형보다 3차원모형의 결과의 정확도가 더 높은 것으로 분석되었다. 곡률반경이 1,300~1,600 정도인 실제하천에 적용한 결과, 수위의 경우 2차원 결과가 3차원 결과보다 최대 3%정도 수위가 높은 것으로 나타났으며, 또한, 상관계수가 평균 0.91의 값을 보이고 있어 2차원모형과 3차원모형의 결과가 비교적 잘 일치하는 것으로 분석되었다. 흐름 분석을 통해서 만곡부에서의 최대유속은 최정점(apex)에서 보다는 오히려 최정점 이전 하도의 내측에서 발생하였으며, 정점에서의 종단유속은 감소하지만 횡단유속은 오히려 크게 증가하는 경향을 보이고 있었다. 따라서 하천설계시 사행하천의 제방 안정성 확보를 위하여 종단유속 뿐만 아니라 횡단유속 또한 고려할 필요가 있음을 확인하였다. 또한 남강댐 하류 만곡부에서의 내측 및 외측의 수위를 분석한 결과, 제방 외측의 수위가 평균수위에 비해 최대 약 37cm정도 증가하는 것으로 분석되었다. 따라서 만곡부에 대한 하천제방설계시 좌, 우안의 여유고를 일률적으로 적용하기 보다는 만곡에 따른 흐름특성을 분석하여 설계에 적용하여야 안정성 및 경제성을 동시에 확보할 수 있을 것으로 사료된다.

• Korean Journal of Plant Resources
• /
• v.25 no.4
• /
• pp.456-464
• /
• 2012

This study was conducted to establish the in vitro optimal condition for seed germination and organogenesis of wild Angelica gigas. The experiment was evaluated the effects of $GA_3$ for pre-treatment with different periods of time (0h, 24h, 48h, 72h) and followed the treatment of seeds by control, scarification and methanol-heating method. As a result, the highest rates (15%) of seed germination was shown under the treatment without soaking of $GA_3$ and methanol-heating treatment. The seed germination was highly increased 60% under the condition of treatment on ultrasonic waves (frequency 80 KHz) with methanol-heating treatment including 0.1 mg/L $GA_3$. The highest callus induction rate was obtained from in vitro germinated stem, root and hypocotyl on the MS medium with 1.0 mg/L NAA and 0.5 mg/L BA. The highest percentages of shooting (50%) and rooting (85%) induction were observed in hypocotyl and root cultured on PGRs free medium and 0.1 mg/L NAA, respectively. In addition, somatic embryogenesis was observed from stem (1.0 mg/L 2,4-D) and hypocotyl (0.1 mg/L NAA).

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.1
• /
• pp.19-30
• /
• 2007

Modeling 3D buildings is an essential process to revive the real world into a computer. There are two ways to create a 3D building model. The first method is to use the building layer of 1:1000 digital maps based on high density point data gained from airborne laser surveying. The second method is to use LiDAR point data with digital images achieved with LiDAR. In this research we tested one sheet area of 1:1000 digital map with both methods to process a 3D building model. We have developed a process, analyzed quantitatively and evaluated the efficiency, accuracy, and reality. The resulted differed depending on the buildings shape. The first method was effective on simple buildings, and the second method was effective on complicated buildings. Also, we evaluated the accuracy of the produced model. Comparing the 3D building based on LiDAR data and digital image with digital maps, the horizontal accuracy was within ${\pm}50cm$. From the above we derived a conclusion that 3D building modeling is more effective when it is based on LiDAR data and digital maps. Using produced 3D building modeling data, we will be utilized as digital contents in various fields like 3D GIS, U-City, telematics, navigation, virtual reality and games etc.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.6
• /
• pp.741-747
• /
• 2009

For construction of 3D virtual city models, airborne digital cameras, laser scanners, multi-oblique photograph systems and other devices are currently being used. With such advanced techniques, precise 3D spatial information can be collected and high quality 3D city models can be built in a considerably large area. The 3D spatial information to be built has to provide the latest information that quickly reflects the causes of any change due to urban development. In this study, a UAV photogrammetric method using low cost UAV and digital camera was proposed to acquire and update 3D spatial information effectively on small areas where information continuously change. In the proposed UAV photogrammetric method, the elements of interior orientation were acquired through camera calibration and the vertical and oblique photographs were taken at 9 points and the 3D drawing of ground control points and buildings was performed using 20 images among the pictured images. This study also analyzed the accuracy of the proposed method comparing with ground survey data and digital map in order to examine whether the method can be used in on-demand 3D spatial information update on relatively small areas.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.3
• /
• pp.259-267
• /
• 2020

For real-time precise positioning, N-RTK (Network Real-Time Kinematic) technology is widely used these days. However, the currently operating N-RTK system has a limitation in terms of the number of users. Therefore, if reference points generate correction messages with no limit on the number of users are developed later, it is determined that an appropriate reference point installation interval is required, so that the accuracy of the N-RTK system according to the baseline distance was analyzed. This experiment utilized receivers with varying performance that estimated the rover position, and RTKLIB, an open-source software, is used for processing data. As a result, the rover position was estimated accurately with a high rate of fixed ambiguity for all the receivers. When the reference station with a baseline length of 40 km was used, the vertical RMSE (Root Mean Squared Error) was quite similar to the short baseline case, but only half of the ambiguity fixing rate was achieved. The outlier in the estimated rover position was not observed for the longer baselines in the case of a high-end receiver. It is necessary to analyze the ambiguity fixing and the accuracy of the kinematic positioning with scientific GNSS processing software.

• Membrane Journal
• /
• v.8 no.4
• /
• pp.235-242
• /
• 1998

Pervaporation separation of methyl tert-butyl ether (MTBE) and methanol (MeOH) mixture, of which the former compound is well known as the octane booster was carried out. Poly(vinyl alcohol) (PVA) membranes crosslinked with poly(acrylic acid) which have been successfully applied on the water-alcohol mixtures were used in this study. The PVA/PAA ratio in the crosslinked membranes was 95/5, 90/10, 85/15, 80/20, and 75/25 by weight. The operating temperatures were 30, 40, and 50$\circ$C, and the compositions of MTBE and MeOH to be separated were 95/5, 90/10, and 80/20 (MTBE/MeOH) solutions. PVA/PAA=85/15 membrane showed the separation factor $\alpha_{MeOH/MTBE}$=4000 and the permeation rate of 10.1 g/m$^2$hr for MTBE/MeOH=80/20 solution at 50$\circ$. When the same membrane was used, the separation factor and permeation rate for MTBE/MeOH=90/10 solution at 40$\circ$C were $\alpha_{MeOH/MTBE}$=6000 and 8.5 g/m$^2$hr, respectively. Also, the hydrophilic/hydrophobic balance of the membranes would take an important role in the relationships between the membranes and separation performances in terms of the flux and the separation factor.

• Journal of the Korean Geographical Society
• /
• v.46 no.2
• /
• pp.168-180
• /
• 2011

The accuracy of rainfall data for a hydrological modeling study is important. NEXRAD (Next Generation Radar) rainfall data estimated by WRS-88D (Weather Surveillance Radar - 1988 Doppler) radar system has advantages of its finer spatial and temporal resolution. In this study, NEXRAD rainfall data was tested and compared with conventional weather station data using the previously calibrated SWAT (Soil and Water Assessment Tool) model to identify local storms and to analyze the impacts on hydrology. The previous study used NEXRAD data from the year of 2000 and the NEXRAD data was substituted with weather station data in the model simulation in this study. In a selected watershed and a selected year (2006), rainfall data between two datasets showed discrepancies mainly due to the distance between weather station and study area. The largest difference between two datasets was 94.5 mm (NEXRAD was larger) and 71.6 mm (weather station was larger) respectively. The differences indicate that either recorded rainfalls were occurred mostly out of the study area or local storms only in the study area. The flow output from the study area was also compared with observed data, and modeled flow agreed much better when the simulation used NEXRAD data.

• Journal of the HCI Society of Korea
• /
• v.5 no.1
• /
• pp.37-43
• /
• 2010

Twitter has been continuously growing since October, 2006. Especially, not only the users and the number of messages have been increasing but also a new concept in social networking called 'micro blogging' has diffused. Within Korea, service such as 'me2day' has already been introduced and the improvement of internet accessibility within mobile devices is expected to expand the 'micro blogs'. In this point, this research is executed to study the new medium, 'micro blog'. To do so, we collected and analyzed Twitter logs of Korean users. Especially, we were curious about the extreme heavy users using Twitter, despite of the linguistic and cultural barrier of the foreign service. Who they are, why and how they use the 'micro blog'. First, we reviewed the general aspect of followers and messages by collecting a certain number of random samples. Using the Lorenz curve we found out that there was the imbalance within the users and based on this phenomenon we deducted an extreme heavy user group. In order to perform further analysis, log analysis was performed on the extreme heavy users. As the result, the users used multiple mobile and desktop 'Twitter' clients. The usage pattern was similar to that of internet usage time but was used during their "micro" time. The users using 'Twitter' not only to spread messages about important information, special events and emotions, but also as a habitual 'chatting tool' to express ordinary personal chats similar to SMS and IM services. In this research, it is proved that 68% of the total messages were ordinary personal chats. Also, with 24% of the total messages were retweets, we were able to find out that virtually connected 'people' and 'relationships' acted as the dominant trigger of their articulation.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.255-260
• /
• 2007

The construction industry has been recognized as lagging behind other industries in the area of research and development (R&D) due primarily to the lack of R&D funds. To overcome this situation, the Korea Ministry of Construction and Transportation has a plan to expand its investments on the construction R&D up to 1.72 billion US dollars over the next 3 years. Despite this effort, it is still challenging to conduct the quantitative measurement on the efficiency of construction R&D projects, which can be utilized as the objective basis in the reasonable selection of a promising R&D team or in the consequential evaluation of a R&D performance. This study aims to conduct the efficiency analysis on the construction R&D projects to provide the basis for evaluating the performance of research and development. Toward this end, this study performs an efficiency analysis, which reflects all of the input and output data into/from the construction R&D by utilizing the Data Envelopment Analysis (DEA). The proposed methodology can be utilized to make a better decision on the priority of the R&D investments and present a sound basis to suggest the areas to be improved so as to reduce the inefficiency of R&D projects.