• Korean Journal of Optics and Photonics
• /
• v.19 no.6
• /
• pp.394-399
• /
• 2008

An integral imaging system enabling enhanced depth of field by incorporating a pair of liquid-crystal (LC) lens arrays was proposed and demonstrated. The lens arrays exhibit two different refractive indexes depending on the light polarization. The proposed LC lens array I and II were implemented by depositing a ZLI-4119 LC and an E-7 LC, respectively, on top of a lens-array substrate in glass. When the two LC lens arrays were aligned appropriately, a birefringence was obtained for a specific light polarization in such a way that the incoming light sees different refractive indexes for them. As a result, the focal length associated with the imaging system utilizing the LC lens arrays was adaptively varied, thereby enhancing the depth of field for the image reconstruction. We have theoretically analyzed the proposed integral imaging system with the $LightTools^{(R)}$ to confirm that the focal length could be adjusted with the help of the birefringent lens array. Finally the proposed imaging system successfully reconstructed the objects. The birefringent lens array employing the ZLI-4119 LC produced a real image with the focal length of 680 mm, while the other using the E-7 LC yielded a virtual image with the focal length of -29 mm.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.2
• /
• pp.171-176
• /
• 2016

By developing rider robot using omni wheel drive, a usability test for 6 people was conducted after finding out inconvenient factors and ways of improvement. The results of this research are as follows. First, we researched inconvenient factors captured by object of experiment using a rider robot who is living in the dormitory. It showed that the disabled showing 1.6 of satisfaction degree felt more inconvenient for normal people showing 4 of satisfaction degree. It was found that the height of seats is 10 centimeters higher, which caused inconvenience for moving. Second, each of the disabled and normal people showed 2.33 and 2.62 of satisfaction degree below the average for seats, back of a seat, armrest, footrest, security belts. However, for the revised design both of them showed 3.5 of satisfaction degree over the average. Third, most people felt this robot is quite expensive and said they would purchase it if subsidized by the government. Therefore, based on inconvenient factors and ways of improvement found in this research, further study needs to be conducted so as to improve the quality of life of the disabled.

• Journal of the Korea Computer Graphics Society
• /
• v.22 no.3
• /
• pp.21-29
• /
• 2016

Cell segmentation is an important but time-consuming and laborious task in biological image analysis. An automated, robust, and fast method is required to overcome such burdensome processes. These needs are, however, challenging due to various cell shapes, intensity, and incomplete boundaries. A precise cell segmentation will allow to making a pathological diagnosis of tissue samples. A vast body of literature exists on cell segmentation in microscopy images [1]. The majority of existing work is based on input images and predefined feature models only - for example, using a deformable model to extract edge boundaries in the image. Only a handful of recent methods employ data-driven approaches, such as supervised learning. In this paper, we propose a novel data-driven cell segmentation algorithm for bright-field microscopy images. The proposed method minimizes an energy formula defined by two dictionaries - one is for input images and the other is for their manual segmentation results - and a common sparse code, which aims to find the pixel-level classification by deploying the learned dictionaries on new images. In contrast to deformable models, we do not need to know a prior knowledge of objects. We also employed convolutional sparse coding and Alternating Direction of Multiplier Method (ADMM) for fast dictionary learning and energy minimization. Unlike an existing method [1], our method trains both dictionaries concurrently, and is implemented using the GPU device for faster performance.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.6
• /
• pp.155-166
• /
• 2016

It is important to configure capacitance(C) of the capacitor and the induction coefficient(L) of the work coil on the resonant circuit design stage in order to induce heating on the object by a precise and constant frequency components in the electromagnetic induction heating equipment. Work coil conducts a direct induction heating according to heating point and area of the object which has a fixed heat factor so that work coil is designed to has fixed value. On the other hands, Capacitor should be designed to be changed in order to be the higher the utilization of the entire equipment. It is extracted the samples by variation of single electrode capacity from the selection stage of raw materials for capacity to the stage of process design for output of the high frequency LC resonance of 700kHz on 1000 VAC maximum voltage and current to $200I_{MAX}$. It is suggested fundamental experiment results in order to prove relation for the optimal design of HF-LC resonance conduction-cooled capacitor based on the response of frequency characteristics and results of output parameters according to variation of the capacitance size.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.7
• /
• pp.419-426
• /
• 2012

The pitch searching is a vital process in a vocoder. Generally, the method of pitch searching is employed after highlighting the periodicity, where a correlation is identified with the signal by changing the interval of two pulses. When the correlation value reaches the peak, the pitch can be found by the pulse interval because it is the repetition interval with most striking period. However if the identified period happens to be one of half period, double period or triple period, this cannot be considered as the pitch period. Many methods were suggested to solve this problem. An inaccurate pitch could be obtained as well, when there is an interval where signal amplitude is not constant but varies abruptly in the frame. To solve this matter, searching the pitch by dividing a frame into various subframes is adopted, but too much calculation has to be followed while it leads the correct value. This paper suggests an algorithm to resolve these two problems. First, to search the pitch after advance correction of the signal energy level with an estimated overall energy change ratio in the frame before pitch search to reduce half period, double period and triple period is suggested. Second, to vary the number of subframes by predicting the amplitude change rate in the frame by the energy ratio obtained by the above-mentioned method is advised. If these two methods are applied, the pitch searching time can be reduced and the general pitch searching performance can be improved without affecting the sound quality in the synthesized signal.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.49 no.3
• /
• pp.15-26
• /
• 2012

Recently, due to applicability increase of vector data based digital map for geographic information and evolution of geographic measurement techniques, large volumed GIS(geographic information service) services having high resolution and large volumed data are flowing actively. This paper proposed an efficient vector map compression technique using the SEC(spatial energy compaction) based on classified bins for the vector map having 1cm detail and hugh range. We encoded polygon and polyline that are the main objects to express geographic information in the vector map. First, we classified 3 types of bins and allocated the number of bits for each bin using adjacencies among the objects. and then about each classified bin, energy compaction and or pre-defined VLC(variable length coding) were performed according to characteristics of classified bins. Finally, for same target map, while a vector simplification algorithm had about 13%, compression ratio in 1m resolution we confirmed our method having more than 80% encoding efficiencies about original vector map in the 1cm resolution. Also it has not only higher compression ratio but also faster computing speed than present SEC based compression algorithm through experimental results. Moreover, our algorithm presented much more high performances about accuracy and computing power than vector approximation algorithm on same data volume sizes.

• Journal of the Korea Concrete Institute
• /
• v.19 no.6
• /
• pp.693-700
• /
• 2007

The maturity method is used to estimate the effects of time and temperature on the strength development of concrete. The purpose of this paper is to show how variable curing temperatures affect strength development for both normal and high-strength concrete using the maturity concept. The experimental results for normal-strength concrete show clearly the cross-over effect of strength development as the time of the peak temperature varied. However, this cross-over effect does not exist after the actual ages are converted to the temperature dependent equivalent age. In other words, the existing maturity method does not include the effect of varying the time to peak temperatures but instead includes the effect of the magnitude of peak temperatures. For high-strength concrete, the results were inconclusive. This fact for normal-strength concrete coincides with the ASTM stated limitation that the existing maturity method doesn't take into account the effect of early age temperature on long-term ultimate strength. The results of this 3-year study are used as a basis for an improved concrete maturity function.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.380-386
• /
• 2001

A nuclear microprobe system with adjustable precision object slits and a magnetic quadrupole doublet was designed by the beam optics simulation using a first order matrix formalism, and installed in a $30^{\circ}$ beam line connected with KIGAM 1.7 MV Tandem VDG Accelerator. Demagnification factors for x and y axis are calculated to be 25 and 4.9, respectively, and a minimum beam spot side is expected to be about 5 $\mu\textrm{m}$ for 3 MeV proton beams with a current of about 1 nA. A multi-purpose octagonal target chamber has been built to facilitate MeV ion-beam analytical techniques of PIXE, RBS, ERDA, and ion beam micro-machining. It contains X-ray and particle detectors, a zoom microscope, a Faraday cup, a 4-axis sample manipulator and a high vacuum pumping system. The system performance of the nuclear microprobe is now being tested, and automatic manipulator control and data acquisition system will be installed for routine applications of micro ion-beam analytical techniques.

• Journal of the Korean Institute of Gas
• /
• v.24 no.5
• /
• pp.29-38
• /
• 2020

It is practically difficult to accurately measure the temperature and concentration of a large combustion systems at industrial sites in real time. Temperature measurement using thermocouple, which are mainly used, is a point-measuring method that is less accurate and less reliable to analyze the wide area range of inner combustion system, and has limitations to internal accessibility. In terms of concentration analysis, most measurement methods use sampling method, which are limited by the difficulty of real-time measurement. As a way to overcome these limitations, laser-based measurement methods have been developed continuously. Laser-based measurement are line-average measurement methods with high representation and precision, which are beneficial for the application of large combustion systems. In this study the temperature and concentration were measured in real time by water vapor and oxygen generated during combustion using Tunable Diode Laser Absorption Spectroscopy (TDLAS). The results showed that the average temperature inside the combustion system was 1330℃ and the mean oxygen concentration was 3.3 %, which showed similar tendency with plant monitoring data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.525-531
• /
• 2011

Exhaust gas recirculation (EGR) is more effective than selective catalytic reduction (SCR) or lean $NO_x$ trap (LNT) for the reduction of $NO_x$ emissions in diesel engines. A large amount of EGR gas is necessary to satisfy the stringent regulations on $NO_x$ emissions. Low pressure loop (LPL) EGR is almost independent of the variable geometry turbocharger (VGT) at a specific boost pressure, so LPL EGR is better than conventional high pressure loop (HPL) EGR in terms of EGR supply. We compare the influence of HPL EGR and LPL EGR on the combustion characteristics at a constant boost pressure in a diesel engine. The dilution ratio was employed as an independent parameter to analyze the effect of the dilution of the intake charge for each EGR loop. At the same level of $NO_x$ emissions, the fuel consumption and smoke opacity were slightly lower for LPL EGR than for HPL EGR.