• Journal of Korea Port Economic Association
• /
• v.36 no.3
• /
• pp.21-38
• /
• 2020

Currently, in-port emissions are a serious problem in port cities. However, emissions, especially non-greenhouse gases, from the operation of cargo handling equipment (CHE) have received significant attention from scientific circles. This study estimates the amount of emissions from on-land port diesel-powered CHE in the Port of Incheon. With real-time activity data provided by handling equipment operating companies, this research applies an activity-based approach to capture an up-to-date and reliable diesel-powered CHE emissions inventory during 2017. As a result, 105.6 tons of carbon monoxide (CO), 243.2 tons of nitrogen oxide (NOx), 0.005 tons of sulfur oxide (Sox), 22.8 tons of particulate matter (PM), 26.0 tons of volatile organic compounds (VOCs), and 0.2 tons of ammonia (NH3) were released from the landside CHE operation. CO and NOx emissions are the two primary air pollutants from the CHE operation in the Port of Incheon, contributing 87.71% of the total amount of emissions. Cranes, forklifts, tractors, and loaders are the four major sources of pollution in the Port of Incheon, contributing 84.79% of the total in-port CHE emissions. Backward diesel-powered machines equipped in these CHE are identified as a key cause of pollution. Therefore, this estimation emphasizes the significant contribution of diesel CHE to port air pollution and suggests the following green policies should be applied: (1) replacement of old diesel powered CHE by new liquefied natural gas and electric equipment; (2) the use of NOx reduction after-treatment technologies, such as selective catalytic reduction in local ports. In addition, a systematic official national emission inventory preparation method and consecutive annual in-port CHE emission inventories are recommended to compare and evaluate the effectiveness of green policies conducted in the future.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.419-425
• /
• 2023

This paper presents the research results of analyzing the high-temperature corrosion characteristics of three currently commercialized heat exchanger tube materials under actual operating conditions of a biomass power plant. In order to precisely analyze the high-temperature corrosion characteristics of these materials, a high-temperature corrosion evaluation device was installed in the power plant equipment, which allows for adjusting the surface temperature of the heat exchanger tubes. Experiments were conducted for approximately 300 hours under various temperature and operating conditions. In this study, the commercialized heat exchanger tube materials used were SA213T12, SA213T22, and SA213T91 alloys. In order to objectively analyze the high-temperature corrosion characteristics of each material, an international standard-based process to remove corrosion products was applied to obtain the weight change of the specimens, and the average thickness loss and corrosion rate were derived. Thus, the high-temperature corrosion results for each condition were quantitatively compared and analyzed. In addition, in order to increase the reliability of the high-temperature corrosion evaluation method introduced in this study, the surface and cross-sectional corrosion of the specimens were confirmed by using scanning electron microscopy and energy-dispersive X-ray analysis. Based on these analysis results, it was found that the corrosion resistance of the commercial heat exchanger materials increases as the content of chrome and nickel in the composition increases. Additionally, it was found that the corrosion phenomenon is rapidly accelerated as the surface temperature increases. Finally, the replacement period (lifetime) of the heat exchanger tubes under each condition could be inferred through this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.595-600
• /
• 2020

The purpose of this paper was to prepare and evaluate solid dispersions (SD) that can increase the dissolution rate of dexibuprofen as a model drug with low solubility in water using saccharides and sugar alcohols as dispersion materials. DSC, XRD, content and content uniformity test, dissolution test, and disintegration test were conducted for physicochemical evaluation of the prepared SD. For the results, it was confirmed using differential scanning calorimetry that fructose, which has a melting point around 120 ℃ of the device operating temperature range, is a suitable excipient for the preparation of SD by the rotary hot-melt granulation (RHMG) method. X-ray diffraction analysis was conducted to confirm that the crystallinity of dexibuprofen was reduced. Disintegration test of the prepared tablet using SD-containing dexibuprofen and fructose confirmed a very fast disintegration time within 1~2 seconds and also showed that the dissolution rate was about 20% faster than that of the dexibuprofen raw material. Dexibuprofen with reduced crystallinity by SD confirmed through the RHMG method can be used to increase the dissolution rate of the drug and increase the disintegration time of the tablet. Thus, it can be used in the manufacturing of various solid preparations.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.551-551
• /
• 2017

우리나라와 동아시아는 경제 성장에 따른 전력수요가 크게 증가하였으며, 증가하는 대부분의 전력수요를 원자력으로 대체하고자 원전을 통한 전력생산 비중을 증가시키고 있다. 현재 중국은 13기의 원전을 가동 중이며, 동남 해안지대에 집중되어 있다. 또한, 건설 중인 원전은 27기로 전세계에서 건설 중인 원전의 41%를 차지한다. 원전의 증가에 따른 방사능 누출에 대한 위험성 역시 증가되고 있는 실정이다. 한국원자력안전기술원에서 중국 중서부지역에서 방사능이 누출될 경우 방사성 물질이 한반도로 이동하는 모의 상황에 대한 시뮬레이션을 통해, 원전 사고 발생 시 사흘 만에 제주도를 포함한 대한민국 전역이 방사성 물질로 뒤덮이는 것으로 분석하였다. 중국에서 누출된 방사성물질은 편서풍을 타고 한반도로 이동하게 되며, 일부는 낙진으로 유역 또는 하천에 유입되고 일부는 동해를 지나 일본으로 이동 할 것이다. 그동안 중국에서의 방사능 누출사고를 통한 방사성물질의 국내유입에 의한 영향에 대한 연구가 부족한 것이 현실이다. 이에 본 연구에서는 중국 텐완에서 원전사고 발생시 국내 하천에 어떠한 영향을 미치는지 분석하고자 환경다매체 모형을 이용하여 방사성물질(세슘, Cs-137)의 영향에 대한 모의를 진행하였다. 중국 텐완원전에서 방사성 Cs-137이 누출되어 춘천지역에 도달하였을 때의 대기중 농도 $5,650Bq/m^3$로 가정하여 모의 시나리오를 구성하였다. 모의 지역은 북한강 수계를 대상으로 하였으며, 7개의 중권역과 549.3 km의 하천이 포함되었다. 다매체 모형 모의를 통해 방사성물질 낙진으로 인한 Cs-137이 북한강 수계에 어떠한 영향을 미치는지 알아보고자 북한강수계의 팔당댐 부근의 오염농도를 모의하였다. 우리나라의 원자력시설 방호 방재법에 따른 상수원 취수기준(먹는물)은 100 Bq/L로 되어있다. 본 연구의 시나리오 모의결과, 모의 1일차에서 45 Bq/L, 모의 8일차에는 먹는물 기준 100 Bq/L를 초과하여 최대 119.56 Bq/L로 오염되는 것으로 모의되었다. 따라서, 반감기가 큰 방사성물질을 유입으로 오염된 하천은 개선하기 위해서는 오랜 시간과 높은 처리비용이 발생되기 때문에 인접국 또는 국내의 방사능 누출로 인한 상수원 오염 발생에 대비한 초기/중 장기적인 대응책 마련이 필요한 시점이다.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.26 no.1
• /
• pp.37-48
• /
• 2021

A new high speed rotation type-passive sampling device (HSR-PSD), which can rotate seawater at high speed and absorb easily and quickly the freely dissolved hydrophobic organic contaminants from seawater, was developed and then applied around the Korean Peninsula. Freely dissolved concentrations (Cfree) of polycyclic aromatic hydrocarbons (PAHs) were determined using the HSR-PSD with low density polyethylene (LDPE) sheets as a passive sampler. Furthermore, dissolved concentrations (Cdissolved) of PAHs in seawater were also obtained from high volume water sampling as a conventional method to account for actual bioavailability. When the LDPE sheets were rotated in the HSR-PSD at 900 rpm, PAHs with log KOW 3.4 ~ 5.2 were equilibrated between the LDPE and water in 5 hours. Although the high molecular weight PAHs with log KOW 5.6 ~ 6.8 was expected to be 2 to 30 days to reach the equilibrium, the Cfree of the PAHs at equilibrium could be corrected using performance reference compounds in 5 hours. Meanwhile, the total Cfree of PAHs were from 0.32 to 1.2 ng/L, which were higher than reported values in other oceans, but lower than in coastal water such as estuary, harbor, or shore. A bioavailability from the detected PAHs was highest at the sampling line near the dumping site of the Yellow Sea. Predicted residual concentrations in biota were relatively higher in offshore including the dumping site than in coastal regions.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.110-110
• /
• 2011

염색공업 폐수는 그 성분이 일반적으로 매우 복잡하며, 작업공정의 가동 사항에 따라 수질 변동이 큰것이 특징으로, 각 공정에서 배출되는 염료, 보조화학물질, PVA(Polyvinyl alchol), 전분, wax 등이 포함되어 있으며 pH가 높고, 색도로 인해 하천에 방류될 경우 확산성이 높아 미생물에 의한 자정작용을 방해하여 하천의 수중생태계를 파괴할 우려가 있다. 이러한 염색산업에서 발생하는 폐수는 일반적으로 응집침전, 부상분리법 등의 전처리한 후 활성오니공정으로 처리하는 방법이 널리 이용되고 있으나, 이들 처리공정으로는 폐수 속에 포함되어 있는 다양한화학적 구조의 색소성분 및 유해물질을 완벽하게 제거하는 것이 어려운 실정이다. 유기물 함량이 높은 염색폐수를 처리하기 위해 제안된 기술로는 산소활성슬러지법, 유동상 및 고정상 생물막법, 포괄고정화법 등이 있다. 이러한 기술들중 기존의 처리공정을 증축없이도 처리효율을 높일 수 있는 방법으로 담체를 이용한 부유메디아 생물막공정(Moving-Bed BioReactor, MBBR)이 있다. 이공정은 미생물이 부착, 성장할 수 있는 공극율과 비표면적이 큰 담체를 이용하므로 반응조내의 부유 미생물 뿐만 아니라 담체에 고농도로 부착된 부착 미생물에 의해서도 유기물을 제거하기 때문에 다른 공정들에 비해 처리효율이 뛰어나고 기존의 활성슬러지 공정에 비해 갑작스러운 부하변동 및 유독성 폐수유입에 대해서도 안정적으로 운전이 가능한 장점이 있다. 본연구에서는 부유메디아 생물반응기(Moving-Bed BioReactor, MBBR)을 이용하여 염색폐수내 $COD_{Mn}$, 색도 및 난분해성 물질인 PVA 저감에 대한 Lab-scale test 수행하였다. 실험에 사용된 염색폐수의 수질은 평균 pH 13, $COD_{Mn}$ 900 mg/L, SS 135 mg/L, 색도 1,134 [C.U.], PVA 593 mg/L였으며, 2L의 반응기를 사용하여 회분식 실험을 수행였다. 본 실험에서는 호기성 미생물에 의한 염색폐수의 생분해가 유지되는데 필요한 최적의 용존산소 농도와 이에 필요한 공기 폭기량을 결정하기 위하여 i) DO uptake rate측정과 ii) 담체의 충진율, iii) COD/N ratio, iv) Air 유량, v) 담체내 흡착제의 종류, vi) $Ca^{2+}$ 첨가가 염색폐수의 생분해에 미치는 영향을 살펴보았다. 운전시간을 7일로 하여 COD, 색도, PVA 등을 측정한 결과 담체를 첨가한 경우가 담체를 첨가하지 않은 경우 보다 제거효율이 뛰어났다. 특히 충진율 30%(C/N 3)의 경우에서 COD, 색도, PVA의 제거율이 각각 평균 65%, 70%, 60%로 가장 높은 제거효율을 나타내었다.

• Journal of Chest Surgery
• /
• v.37 no.3
• /
• pp.235-244
• /
• 2004

Anatomic correction of the transposition of the great arteries (TGA) or Taussig-Bing anomaly by means of the arterial switch operation is now accepted as the therapeutic method of choice. This retrospective study was conducted to evaluate the risk factors for operative deaths and the efficacy of technical modification of the coronary transfer. 85 arterial switch operations for TGA or Taussig-Bing anomaly which were performed by one surgeon from 1994 to July 2002 at Dong-A university hospital were included in this retrospective study Multivariate analysis of perioperative variables for operative mortality including technical modification of the coronary transfer was peformed. Overall postoperative hospital mortality was 20.0% (17/85). The mortality before 1998 was 31.0% (13/42), but reduced to 9.3% (4/43) from 1998. The mortality in the patients with arch anomaly was 61.5% (8/13), but 12.5% (9/72) in those without arch anomaly. In patients who underwent an open coronary reimplantation technique, the operative mortality was 28.1% (18/64), but 4.8% (1/21) in patients undergoing a technique of reimplantation coronary buttons after neoarotic reconstruction. Risk factors for operative death from multivariated analysis were cardiopulmonary bypass time ($\geq$ 250 minutes), aortic cross-clamping time ($\geq$ 150 minutes), aortic arch anomaly, preoperative event, and open coronary reimplantation technique. Operative mortality has been reduced with time. Aortic arch anomaly and preoperative events were important risk factors for postoperative mortality. However atypical coronary artery patterns did not work as risk factors. We think that the technical modification of coronary artery transfer played an important role in reducing the postoperative mortality of arterial switch operation.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.2
• /
• pp.35-43
• /
• 2011

Permeable Reactive Barriers (PRB) method is an economical method that does not require any other methods to be operated once it is installed as it controls of groundwater flow in the barrier, which is inserted a reactive material on the way of pollutant. The major dominant element of PRB is a reactive material in the reactive wall, and such factors as purification efficiency and used time based on the chemical and physical features in between the reactant and pollutant. High purification efficiency can be expected when a rational design that is synthetically considered in features of packing density, operation period, and adsorption reactant of pollutant. A column test was conducted for an application test using CFW as its adsorption reactant in order to remove copper($Cu^{2+}$) in the PRB system. The CFW was used for the reactant and selected inflow speed, density and thickness of PRB as its necessary factors for design of PRB. As a result of the experiment, the removal efficiency decreased as operating time of PRB increased and the efficiency linearly increased upon the length. Therefore, it is confirmed that the thickness of reactive materials in PRB system can be designed using the proposed formula considering purification time and density of CFW.

• Tuberculosis and Respiratory Diseases
• /
• v.66 no.4
• /
• pp.300-308
• /
• 2009

Background: The quality of care for patients with community acquired pneumonia needs to be improved; the factors affecting this care need to be analyzed. The objectives of this study were used to measure the performance of care processes of for patients with pneumonia and to determine those patient and hospital characteristics are associated with quality care. Methods: The analysis was performed using data from 21 hospitals that had over 500 beds for 1,001 patients, who were sampled randomly. All patients were born before 31 December 1989, and discharged between the two months' August 2006 and October 2006. Performance process indicators were measured by respective hospital, and multivariate logistic regression was used to calculate associations between patients and hospital characteristics using 4 process indicators. Results: Performance rates in timely assessment of oxygenation assessments and blood cultures, correct administration of antibiotic medications, and blood culture performed prior to initial antibiotics were 69.4%, 79.1%, 82.5% and 60.5%, respectively. Age had a positive affect on oxygenation assessment within 24 hours. Bed number, number of nurses per bed, annual number of emergency department visits, average percentage of beds filled, location and arrival time, and site were factors associated with process indicators. Conclusion: It is necessary to make up for the weak points in the process of care for patients with community acquired pneumonia, by enforcing quality assurance. To reduce performance rate variation among hospitals, improvement in care protocols is required for hospitals that have poor quality of care levels.

• Journal of Chest Surgery
• /
• v.42 no.4
• /
• pp.473-479
• /
• 2009

Background: Retrograde autologous priming (RAP) is known to be useful in decreasing the need of transfusions in cardiac surgery because it prevents excessive hemodilution due to the crystalloid priming of cardiopulmonary bypass circuit. However, there are also negative side effects in terms of blood conservation. We analyzed the intraoperative blood-conserving effect of RAP and also investigated the efficacy of autotransfusion and ultrafiltration as a supplemental method for RAP. Material and Method: From January 2005 to December 2007, 117 patients who underwent isolated coronary artery bypass operations using cardiopulmonary bypass (CPB) were enrolled. Mean age was 63.9$\pm$9.1 years (range 36$\sim$83 years) and 34 patients were female. There were 62 patients in the RAP group and 55 patients in he control group. Intraoperative autotransfusion was performed via the arterial line. RAP was done just before initiating CPB using retrograde drainage of the crystalloid priming solution. Both conventional (CUF) and modified (MUF) ultrafiltrations were done during and after CPB, respectively. The transfusion threshold was less than 20% in hematocrit. Result: Autotransfusions were done in 79 patients (67.5%) and the average amount was 142.5$\pm$65.4 mL (range 30$\sim$320 mL). Homologous red blood cell (RBC) transfusion was done in 47 patients (40.2%) and mean amount of transfused RBC was 404.3$\pm$222.6 mL. Risk factors for transfusions were body surface area (OR 0.01, 95% CI 0.00 $\sim$ 0.63, p=0.030) and cardiopulmonary bypass time (OR 1.04, 95% CI 1.01 $\sim$ 1.08, p=0.019). RAP was not effective in terms of the rate of transfusion (34.5% vs 45.2%, p=0.24). However, the amount of transfused RBC was significantly decreased (526.3$\pm$242.3ml vs 321.4$\pm$166.3 mL, p=0.001). Autotransfusion and ultrafiltration revealed additive and cumulative effects decreasing transfusion amount (one; 600.0$\pm$231.0 mL, two; 533.3$\pm$264.6 mL, three; 346.7$\pm$176.7 mL, four; 300.0$\pm$146.1 mL, p=0.002). Conclusion: Even though RAP did not appear to be effective in terms of the number of patients receiving intraoperative RBC transfusions, it could conserve blood in terms of the amount transfused and with the additive effects of autotransfusion and ultrafiltration. If we want to maximize the blood conserving effect of RAP, more aggressive control will be necessary - such as high threshold of transfusion trigger or strict regulation of crystalloid infusion, and so forth.