• The Journal of the Acoustical Society of Korea
• /
• v.35 no.1
• /
• pp.16-23
• /
• 2016

Present study shows three different methods finding the eigenfrequencies of an infinite circular cylinder under free-vibration; Elasticity theory that can be applied to general case, thin-shell theory that can be effectively applied to the cylinders with small thickness, and numerical study using Finite Element Method (FEM). The results obtained from those methods were verified through the cross check among the calculations. Changing the thickness of the cylinder for a fixed outer radius, all the eigenfrequencies below 1 kHz were found and their dependences on the modal index and the thickness were observed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.4
• /
• pp.401-410
• /
• 2008

The natural frequency of a beam plays an important role in not only vibration analysis but also understanding its dynamic characteristics. It is complicated to analyse the natural frequency of a stepped beam with discontinuously varying section. Approximate analysis methods such as Rayleigh-Ritz method, FEM, etc. are frequently used for the vibration analysis of stepped beams. In such a case, accuracy of these methods depends upon the number of partitioned elements, the number of the iterations in calculation and the assumed mode shape. This study presents an approximate analysis method for the fundamental natural frequency analysis of stepped cantilever beam, using equivalent beam transformation technique. Validity and usefulness are verified by comparing the proposed method with FEM for several example problems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.208-212
• /
• 1995

공기 압축기는 건설 및 토목공사 현장 등의 산업현장을 비롯하여 각종 공장에서 광범위하게 사용되고 있다. 공기 압축기에 공급하는 동력은 전기를 사용한 모터와 연료를 사용한 엔진으로 구분할 수 있으며 전기가 공급되지 않는 사용현장에서는 엔진 구동형 공기 압축기가 선택될 수 밖에 없다. 엔진 구동형 공기 압축기는 발생소음도가 모터 구동형보다 훨씬 높음으로 인하여 주변환경에의 소음으로 인한 피해를 줄이기 위하여 방음형의 개발이 절실하게 요구되고 있다. 따라서 본 연구는 기존의 비방음형 공기 압축기에 대하여 방음형을 개발하여 시제품을 제작하고 평가하는데 그 목적이 있다.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2485-2488
• /
• 2003

본 논문에서는 DSP를 이용하여 운동하는 물체의 회전량을 측정하는 실린더형 진동 자이로스코프(이하 자이로) 제어기를 개발하였다. 진동 자이로를 구동하기 위해서는 정밀 진동제어와 신호 처리와 같은 고급 제어 기술이 필요하다. 정밀진동제어는 진동 자이로를 구동하기 위해 필요한 핵심기술로써 기존의 PLL(phase-locked loop)방식은 외부환경에 민감하여 구현이 까다로울 뿐만 아니라 자이로 개개의 고유 진동수가 다르기 때문에 대량 생산에 어려움이 있었다. 또한 자이로 출력 신호로부터 회전량을 검출하기 위해서는 진폭과 당향성 검출의 본 회로뿐만 아니라 잡음 제거와 신호 증폭, 온도 보상과 같은 전처리 과정도 필요하다. 본 논문에서는 DSP를 통해 정밀 진동제어와 잡음 제거, 방향성 검출 등의 기능들을 구현하였으며 증폭과 진폭(회전량) 검출은 아날로그 회로를 이용하였다. 또 한 외부와의 인터페이스를 위해 D/A 회로를 설계하였고 이들을 실험을 통해 검증하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.227-238
• /
• 1988

The curved structures in space, such as multi-level inter-changes, ramped structures, and circular curved structures etc., are modelled as helically curved members with constant helix angle in this study. Equilibrium equations are derived, considering the geometrical properties and initial curvatures of helix. Modal equations of the simply supported helically curved members which can calculate the normalized natural frequencies are derived from these equations by assuming the modal shape function. These equations are used to calculate the normalized natural frequencies of the simply supported helically curved members and verify the distribution of the natural frequencies of them.

• Journal of KSNVE
• /
• v.5 no.2
• /
• pp.257-264
• /
• 1995

We designed the cutter profile for symmetric screw rotor and did vibration experiment of screw rotor manufactured by the designed cutter profile. The results of this study are summarized as follows. (1) We designed the cutter profile of screw rotor (4-6)(5-6) by using numerical analysis program. (2) The maximum amplitude and variation of amplitude of 5-6 profile rotor are about 30 - 36.7% and 10 - 25% smaller than those of 4-6 profile rotor, respectively. (3) As the angular velocity of rotor changes from 100 to 300 rpm, the vibration of X, Y axis in driving shaft of 5-6 profile rotor is about 10 - 20% smaller than that of 4-6 profile rotor.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.95-103
• /
• 1991

A series of experiments were performed to see the dependence of the response characteristics of vortex-induced vibration of flexible cylinders on mass rations for marine applications. Experiments were conducted in the $60cm{\times}60cm$ test section of the cavitation tunnel at the Korea Research Institute of Ships and Ocean Engineering using 5 test rods of 60cm length and 6mm diameter with different mass ratios. It was confirmed quantitatively from the experiments that the low mass ratio cylinders have much broader flow velocity range of large amplitude vibrations than high mass ratio ones.

• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.57-64
• /
• 2023

An open pulsating heat pipe operates continuously by inflow and outflow fluids through an open-type condenser. The open pulsating heat pipe is a device capable of obtaining the thrust due to the variation of internal pressure during phase change. Therefore, the open pulsating heat pipe is a suitable device to move fluids if the heat source such as waste heat exists. Many numerical studies have not been sufficiently conducted on the open pulsating heat pipe. In this study, the numerical analysis of the open pulsating heat pipe is performed according to the length of the condenser section. The OpenFOAM software is used to obtain the thrust and the flow visualization for the open pulsating heat pipe.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.44-49
• /
• 2007

It is well known that the acoustic cavity inside the tire-wheel assembly contributes to vehicle interior noise. In this paper, we have performed acoustic and structural modal testings to investigate the influences of the acoustic cavity resonance on structural vibration characteristics for the tire in free-suspension and for the loaded tire. The testings have given us some findings, which are reported in this paper.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.60-66
• /
• 2002

본 연구는 진동형 구기자 수확기를 개발함에 있어서 탈과된 열매를 손상없이 집과하여 수확작업의 노동력 및 경제적 비용을 줄이고, 농산물 수확의 기계화를 활성화 시키는데 그 목적을 두었다. 생물학적, 재배학적, 그리고 환경적 요인들을 고려하여 탈과열매의 효과적인 집과를 위한 집과장치를 설계·개발하고, 성능시험을 실시하여 집과장치의 집과효율을 분석 하였으며, 그 결과는 다음과 같다. 1. 수확시작기의 주행시에는 집과안내장치가 구기자 나무 밑부분과 부딪침이 없고, 탈과작업시에는 구기자 나무 밑의 공간까지 집과기능을 갖도록, 4절 링크 시스템을 이용하여 집과 안내장치를 개폐식으로 설계제작하였다. 2. 개폐식으로 제작된 집과장치를 진동형 구기자 수확기 시작기에 장착하여 성능시험을 한 결과, 숙과의 수집율은 88∼96%로 나타났다. 3. 미수집율인 4∼12%는 개폐식 집과장치의 기능저하로 인하여 발생한 것이 아니고, 기계전후 방향의 열매의 튐 현상에 의한 것이었으며, 이 손실은 비산방지막 커튼의 설치로 보완되리라 사료되었다.