• 센서학회지
• /
• 제32권6호
• /
• pp.470-474
• /
• 2023

In this study, a diaphragm-type pressure sensor was developed using multi-layer(four-layer) graphene produced at 1 nm thickness by thermally transferring single-layer graphene produced by chemical vapor deposition (CVD) to a 6" silicon wafer. By measuring the gauge factor, we investigated whether it was possible to produce a pressure sensor of consistent quality. As a result of the measurement, the pressure sensor using multilayer graphene showed linearity and had a gauge factor of about 17.5. The gauge factor of the multilayer graphene-based pressure sensor produced through this study is lower than that of doped silicon, but is more sensitive than a general metal sensor, showing that it can be sufficiently used as a commercialized sensor.

• 한국진공학회지
• /
• 제22권6호
• /
• pp.306-312
• /
• 2013

화학적 증기증착(Chemical Vapor Deposition, CVD) 방법을 이용하여 단결정 Indium antimonide (InSb) 나노와이어를 $SiO_2$ wafer 위에 성장시켰으며, 성장된 InSb 나노와이어의 결정성과 조성비를 X-Ray Diffraction (XRD)과 Energy Dispersive x-ray Spectroscopy (EDS)의 측정을 통하여 확인하였다. 또한, 반응 source로 사용된 InSb 분말의 기상화(vaporization) 정도를 source container의 모형, 즉 open 및 close 시스템으로 변형하여 조절하였고 이렇게 성장된 InSb 나노와이어들의 구조적 특성을 주사전자현미경(Scaning Electron Microscopy, SEM)을 통하여 자세히 분석함으로써, 그들의 성장과정을 Vapor-Liquid-Solid (VLS) 및 Vapor-Solid (VS) 메커니즘으로 설명하였다. Open-boat를 사용하여 나노와이어를 성장시켰을 경우, close-boat 의 경우와 비교하여 합성된 나노와이어의 yield가 높았으며 나노와이어의 길이와 두께도 증가하는 현상이 관측되었다. 이러한 결과는, InSb source 의 기상화 정도가 close-boat에서 보다 open-boat에서 더욱 가속화되면서 공통적으로 일어나는 VLS 성장 이외에 VS 성장이 추가적으로 진행되어지기 때문으로 추측되어진다. 또한, 반응시간을 증가시켰을 때, 나노와이어의 두께가 증가하는 결과를 통하여 InSb 나노와이어의 성장에서 VS 메커니즘이 우세하게 작용하고 있음을 확인할 수 있었다.

• Carbon letters
• /
• 제21권
• /
• pp.16-22
• /
• 2017

Cobalt was electrodeposited onto chemical vapor deposition (CVD) graphene/Si/$SiO_2$ substrates, during different time intervals, using an electrolyte solution containing a low concentration of cobalt sulfate. The intention was to investigate the details of the deposition process (and the dissolution process) and the resulting magnetic properties of the Co deposits on graphene. During and after electrodeposition, in-situ magnetic measurements were performed using an (AGFM). These were followed by ex situ morphological analysis of the samples with ${\Delta}t_{DEP}$ 30 and 100 s by atomic force microscopy in the non-contact mode on pristine CVD graphene/$SiO_2$/Si. We demonstrate that it is possible to electrodeposit Co onto graphene, and that in-situ magnetic measurements can also help in understanding details of the deposition process itself. The results show that the Co deposits are ferromagnetic with decreasing coercivity ($H_C$) and demonstrate increasing magnetization on saturation ($M_{SAT}$) and electric signal proportional to remanence ($M_r$), as a function of the amount of the electrodeposited Co. It was also found that, after the end of the dissolution process, a certain amount of cobalt remains on the graphene in oxide form (this was confirmed by X-ray photoelectron spectroscopy), as suggested by the magnetic measurements. This oxide tends to exhibit a limited asymptotic amount when cycling through the deposition/dissolution process for increasing deposition times, possibly indicating that the oxidation process is similar to the graphene surface chemistry.

• Carbon letters
• /
• 제28권
• /
• pp.72-80
• /
• 2018

In this study, an empirical relationship between the energy band gap of multi-walled carbon nanotubes (MWCNTs) and synthesis parameters in a chemical vapor deposition (CVD) reactor using factorial design of experiment was established. A bimetallic (Fe-Ni) catalyst supported on $CaCO_3$ was synthesized via wet impregnation technique and used for MWCNT growth. The effects of synthesis parameters such as temperature, time, acetylene flow rate, and argon carrier gas flow rate on the MWCNTs energy gap, yield, and aspect ratio were investigated. The as-prepared supported bimetallic catalyst and the MWCNTs were characterized for their morphologies, microstructures, elemental composition, thermal profiles and surface areas by high-resolution scanning electron microscope, high resolution transmission electron microscope, energy dispersive X-ray spectroscopy, thermal gravimetry analysis and Brunauer-Emmett-Teller. A regression model was developed to establish the relationship between band gap energy, MWCNTs yield and aspect ratio. The results revealed that the optimum conditions to obtain high yield and quality MWCNTs of 159.9% were: temperature ($700^{\circ}C$), time (55 min), argon flow rate ($230.37mL\;min^{-1}$) and acetylene flow rate ($150mL\;min^{-1}$) respectively. The developed regression models demonstrated that the estimated values for the three response variables; energy gap, yield and aspect ratio, were 0.246 eV, 557.64 and 0.82. The regression models showed that the energy band gap, yield, and aspect ratio of the MWCNTs were largely influenced by the synthesis parameters and can be controlled in a CVD reactor.

• 한국세라믹학회지
• /
• 제27권2호
• /
• pp.219-225
• /
• 1990

Silicon dioxide thin film has been grown by a chemical vapor deposition (CVD) technique using SiH4, and O2 gaseous mixture on a silicon substrate. The experimental results indicated that the deposition rate as a function of the input ratio (O2/SiH4) shows two regions, increasing region and decreasing region. Also the deposition rate increases with increasing the deposition temperature. The microstructure of deposited silicon dioxide films is amorphous. The experimental results of infrared absorption spectrums indicate that Si-H and Si-OH bond increase with decreasing input ratio, but Si-O bond is independent on the input ratio. The interfacial charge of deposited silicon dioxide decreases with increasing input ratio.

• 전기학회논문지
• /
• 제56권1호
• /
• pp.132-138
• /
• 2007

Carbon nanotubes (CNTs) arc grown on Ni catalysts employing an inductively-coupled plasma chemical vapor deposition (ICP-CVD) method. The structural and field-emissive properties of the CNTs grown are characterized in terms of the substrate-bias applied. Characterization using the various techniques, such as field-omission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), Auger spectroscopy (AES), and Raman spectroscopy, shows that the structural properties of the CNTs, including their physical dimensions and crystal qualities, as well as the nature of vertical growth, are strongly dependent upon the application of substrate bias during CNT growth. It is for the first time observed that the provailing growth mechanism of CNTs, which is either due to tip-driven growth or based-on-catalyst growth, may be influenced by substrate biasing. It is also seen that negatively substrate-biasing would promote the vertical-alignment of the CNTs grown, compared to positively substrate-biasing. However, the CNTs grown under the positively-biased condition display a higher electron-emission capability than those grown under the negatively-biased condition or without any bias applied.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.482-486
• /
• 2004

The application of focused ion beam (FIB) technology in micro/nano machining has become increasingly popular. Its use in micro/nano machining has advantages over contemporary photolithography or other micro/nano machining technologies, such as small feature resolution, the ability to process without masks and being accommodating for a variety of materials and geometries. This paper presents that the recent development and our research goals in FIB nano machining technology are given. The emphasis will be on direct milling, or chemical vapor deposition techniques (CVD), and this can distinguish the FIB technology from the contemporary photolithography process and provide a vital alternative to it. After an introduction to the technology and its FIB principles, the recent developments in using milling or deposition techniques for making various high-quality devices and high-precision components at the micro/nano meter scale are examined and discussed. Finally, conclusions are presented to summarize the recent work and to suggest the areas for improving the FIB milling technology and for studying our future research.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.519-524
• /
• 2018

Carbon/carbon composites (C/C) have been widely studied in the aerospace field because of their excellent thermal shock resistance and specific strength at high temperature. However, they have the problems that is easily oxidized and deteriorated under atmospheric environment. In order to overcome these shortcomings, the CVD coating of ultra-high-temperature ceramics to C/C has become an important technical issue. In this study, thermodynamic calculations were performed to TaC CVD coating on C/C by FactSage 6.2 program. The Ta-C phase diagrams were constructed with the results of thermodynamic calculations in the Ta-C-H-Cl system. Based on the Ta-C phase diagram, the experimental conditions were designed to confirm the deposition of various phases such as TaC single phase, TaC + C and $TaC+Ta_2C$ by varying the composition of Ta/C ratio. The deposited films were found to be in good agreement with the predicted phases.

• 반도체디스플레이기술학회지
• /
• 제19권2호
• /
• pp.16-21
• /
• 2020

How accurately reproducible energy is delivered to the wafer in the process of making thin films using PE-CVD (Plasma enhanced chemical vapor deposition) during the semiconductor process. This is the most important technique, and most of the reaction on the wafer surface is made by thermal energy. In this study, we studied the method of monitoring the change of thermal energy transferred to the wafer surface by monitoring the temperature change according to the change of the thin film formed on the showerhead facing the wafer. Through this research, we could confirm the monitoring of wafer thin-film which is changed due to abnormal operation and accumulation of equipment, and we can expect improvement of semiconductor quality and yield through process reproducibility and equipment status by real-time monitoring of problem of deposition process equipment performance.

• Elastomers and Composites
• /
• 제45권4호
• /
• pp.298-308
• /
• 2010

패럴린 박막의 기계적 성질과 표면 특성을 개선하기 위해 Xylydene계 다이머(DPX-C, DPX-D, DPX-N)를 사용하여 각각의 다이머에 대한 증착 조건과 투입량에 따른 박막의 두께를 조절함으로써 단일 패럴린-C, D, N 박막과 두 가지 타입이 혼합된 하이브리드 타입의 화학적, 물리적 패럴린 박막을 제조하였다. 패럴린 증착은 화학기상증착법(chemical vapor deposition: CVD)을 이용하였으며, 열분석을 통해 단일 박막과 하이브리드 타입의 박막에 대한 열적 특성을 비교 분석하였다. 인장 강도와 신장율 그리고 인열력 시험을 통해 박막에 대한 기계적 물성을 알아보았으며, 접촉각과 표면 에너지를 측정하여 박막에 대한 표면 특성을 관찰하였다. 두 가지 타입이 혼합된 하이브리드 타입의 화학적 패럴린 박막은 서로 다른 다이머의 장단점을 상호 보완시켜 줄 수 있으며, 물리적 패럴린 박막은 기재에 코팅되는 면과 반대 면의 박막 특성을 자유롭게 조절할 수 있다.