• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1400-1402
• /
• 1994

Plasma polymerized thin films was prepared using an interelectrod inductively coupled gas-flow-type reactor. Styrene was chosen as the monomer to be used. This thin films were also delineated by the electron-beam apparatus with an acceleration voltage 30kV, and the pattern in the resist was developed with RIE 80 with argon gas mixture ratio, pressure and RF power. The molecular structure of thin films was investigated by GPC and FT-IR and then was discussed in relation to its quality as a resist. In the case of plasma polymerization, thickness of resist could be controlled by discharge duration and power. Also etch rate is increased as to growing pressure with RIE 80.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.3
• /
• pp.1-10
• /
• 1998

A new oscillator configuration is presented and tested for Josephson voltage standard operated at the cryogenic(4.2K) temperature. Features of active devices are investigated in aspects of 1/f noise, output power, and current collapse at low temperature. The output power of oscillator is optimized by a nonlinear design approach called Harmonic Two Signal Method(HTSM). The embedding newworks of the generalized six oscillators with tow loads are derived. A HEMT oscilliator is designed in X-Band for the Josephson voltage standard and tested at room and cryogenic(4.2K) temperatures. Oscillation frequency, output power, C/N ratio, and fequency stability are compared at room and low temperatures.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.46-48
• /
• 1998

This paper introduces the design method of a variable reluctace liner pulse motor to be analysed by a 3-dimensional problem in the 2-dimension. And it shows the thrust force density with respect to the ratio of the slot width to the teeth width, the height of mover and the height of tooth.

• YAKHAK HOEJI
• /
• v.37 no.4
• /
• pp.356-361
• /
• 1993

A sensitive method for the determination of methamphetamine(MA) and amphetamine(AM) in hair was developed by gas chromatography/mass spectrometry using stable isotope-labeled internal standards, amphetamine-d$_{5}$ and methamphetamine-d$_{5}$. Hair sample was washed with MeOH, incubated with MeOH(I% HCI) overnight at $37^{\circ}C$ while stirring and extracted using solid phase extraction column on a vacuum manifold. The extract obtained was pentafluoropropionated, and applied to GC/MS. The calibration curves of MA and AM were linear from 2.5 to 250 ng (r>0.99 for both). The limit of detection was 0.1 ng/mg in hair and cut-off level was set at 0.25 ng/mg for both. Hair samples of 27 MA abusers showed positive results in the range 0.7 to 106.8 ng/mg. AM, its metabolite, was detected in 20 out of 27 samples. The ratio of MA versus AM was 4.6~38.3 in specimens. Hair analysis for methamphetamine by GC/MS is an effective method for identifying long-term drug abusers.

• Journal of the Korean Applied Science and Technology
• /
• v.8 no.2
• /
• pp.169-174
• /
• 1991

These studies were carried out to investigate the effects of Korean Job's tears on increasing control of body weight and organ and lipid in rats which were devided into control group, 10% Job's tears group(A), 20% Job's tears group(B), 30% Job's tears group(C), 60% Job's tears group(D) during 10 week administration after 3 week adaption before the experiment. 1. Food intake amount and food efficiency ratio decreased much better Job's tears amount in diet controled of body weight increasing. 2. The organ weight in 100g body weight heavier better 60% Job's tears group(D) then control group. 3. Serum lipid level are rowed Total cholesterol, Free-cholesterol levels in 60% Job's tears group, showed highed of HDL-cholesterol, TG levels.

• Bulletin of the Korean Chemical Society
• /
• v.8 no.2
• /
• pp.79-83
• /
• 1987

The reduction of a series of 1-substituted benzyl-3-cyanoquinolinium ions (p-$cH_3$, H, p-Br, m-F, p-CN) by sodium borohydride has been investigated. In all cases the products from these reactions were found to be 1, 2-dihydroquinolines over 82% yields. Rates of reduction were measured in basic condition and in solvent system consisting of 4 parts of isopropyl alcohol and 1 part of water by volume. Second order rate constants were obtained for these reactions. When the ratio of [$OH^-$] to [$BH_4^-$] becomes large the observed rate constants ($K_{obs}$) decrease by a small factor. Reaction scheme and rate law are discussed. Bronsted ${\alpha}(=\frac{d\;In\;k}{d\;In\;K})$ obtained by using the value of equilibrium constant K, which was obtained previously, was not 0. Instead, a value of 0.36 was obtained which indicated that the reduction by borohydride was structure-dependent according to the Marcus formalism even though the reaction rate was close to the diffusion limit.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.6
• /
• pp.595-599
• /
• 1989

The effects of phosphatidic acid(PA) on the activity of phospholipase D were examined in detail. The enzyme activity was examined in the liposome system containing phosphatidylcholine and PA, which was suspended in a desired buffer solution by ultrasonication. The substrate of large unilamella vesicle (LUV) state by ultrasonication was more effective on the enzyme activity than that of multilamella vesicle(MLV) by water-bath type sonication. The most effective molar ratio of PC-PA liposome for enzyme activity was found to be 1:0.7. The other optimum conditions were found 5 mM $Ca^{2+}$ ion, pH 6.6, and incubation temperature of $27^{\circ}C. K_m \;and \;V_{max}$ values were estimated to be 1.43 mM and 0.8 $nmole/min/{\mu}g$ protein respectively. These properties in a PC-PA liposome system were compared with those in a PC-SDS mixed micelle system. The effects of other phospholipids and organic phosphates on the enzyme activity were also examined.

• Transactions of Materials Processing
• /
• v.27 no.6
• /
• pp.379-385
• /
• 2018

This study investigated the effect of extrusion conditions on microstructures and mechanical properties of AM80 magnesium alloys. The billets of magnesium alloy used for hot extrusion were prepared by permanent mold casting method, and its extrusion was hot direct extrusion with different extrusion conditions. The results of microstructural analysis showed that the main phases in the as-casted alloys were ${\alpha}-Mg$, ${\beta}-Mg_{17}Al_{12}$, and lamella $Mg_{17}Al_{12}$. Hot extrusion results, The tensile strength of the most soundly manufactured extruded bars (extrusion temp: $350^{\circ}C$, extrusion ratio: 27:1, ram speed: 2mm/s) was approximately 327MPa at room temperature. The increase in the mechanical properties of hot-extruded alloys was as a result of grain refinement by dynamical recrystallization during hot extrusion.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.7
• /
• pp.71-78
• /
• 2019

This paper describes a design for a RF receiver to receive satellite digital audio service. The RF receiver designed in this study is a planar structure that is easy to install on the rooftop of a car and is compact in size. In addition, it can be applied to certain commercial models because it has low noise and high gain characteristics. The impedance bandwidth of antenna is 17.8%(415MHz), and the axial ratio is below 3dB as good properties for the bandwidth of 40MHz which is a satellite digital audio service band. Also, it had a broad radiation beamwidth of $95.41^{\circ}$ in H-plane and $117.45^{\circ}$ in E-plane. From the results of the field test of satellite digital audio service reception for the RF receiver, it demonstrated good C/N rate(10.2dB).

• Proceedings of the Korean Society for Applied Microbiology Conference
• /
• 1978.10a
• /
• pp.206.4-206
• /
• 1978

By utilizillg whole cell enzyme of the Xantho-monas citri IFO 3835, cephalexin is synthesized directly from 7-amino-deacetoxy cephalosporanic acid (7-ADCA) and phenyl glycine methyl ester (PGM). To date, cephalexin has been manufactu-red by chemical process involving fairly large number of steps to protect the amino group of phenly glycine and carboxyl group of 7-ADCA. However, the enzymatic process involves only a single step with 85％ conversion in 90 minutes. The fermentation variables studied indicate that oxygen transfer is limiting step in the enzyme production. Optimum conditions for enzymatic reaction were 37 C, pH 6.0, and the optimum substrate molar ratio of PGM to 7-ADCA was 2. Other variables that are related to the biochemical properties of whole cell enzyme temperature stability, pH stability, kinetic constants, reusing effect, enzyme loading effect were also evaluated.