• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.6
• /
• pp.484-488
• /
• 1987

The model experiments were performed in tile circular water tank on the simple cambered and the super-V otter boards attached with the slotted fowler flap at the trailing edge in order to develop more efficient shearing characteristics. The dimension of the model otter boards was varied slightly in the flap chord ratio $0.20\~0.22$ and in the area $432\~426cm^2$ in accordance with the flap angle $30\~50^{\circ}$. The maximum shearing coefficient $C_L=1.78$ and hydrodynamic efficiency $C_L/C_D=4.0$ in the superV type were higher than their efficiencies $C_L=1.75$ and $C_L/C_D=3.7$ in the simple cambered type. As the shearing forces of the otter boards with flap were increased $20\~30\%$ mere than these without flap in spite of increasing the drag and the instability. The effect of flap should be fully investigated for the application.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.947-949
• /
• 1987

This paper describes the design of echo cancslling method(ECM) for transmission with full-duplex which ie transmitted on "2B+D"(144kbps)data through two-wire loop plants. The design objective is 40dB attenuation with a signal-to-noise ratio of $10{\sim}20dB$. Since the transhybrid loos can be as low as $6{\sim}10dB$, the required attenuation of the echo signal is on the order of $50{\sim}55dB$. The used algorithms based on the sign algorithm, and have been improved by using adoptive reference voltage level algorithm.

• KSBB Journal
• /
• v.9 no.4
• /
• pp.365-371
• /
• 1994

The effects of ratios of initial concentration of carbon source to the initial concentration of nitrogen source in the fermentation media on both the yields of PHB fermentation variables and the accumulation of poly-${\beta}$-hydroxybutyric acid(PHB) were investigated. The fermentation media were composed of the combination of varing glucose concentrations, 10, 20, 25, 30, 40, $50g/\ell$ and the NH4Cl concentrations 0.33, 0.4, 0.5, 1.5, 3, $5g/\ell$. The yield of biomass on glucos, Yx/s, decreased very slowly according to the increase of the ratio of C to N. And the yield became constant at 0.35(g biomass/g glucose) with the ratio higher than 70. The yield of residual biomass, Yx/s, also decreased with the ratio of C to N and finally showed a constant value of 0.065(g residual biomass/g glucose) when the ratio was higher than 65. In accordance with the augmentation of the ratio, the yield of PHB, YPHB/S, however, increased and showed the maximum value of 0.35 (g PHB/g glucose) between 40 and 60 of the ratio. The maximum yield of PHB to the change of biomass, YPHB/S, was 0.87(g PHB/g biomass), and the yie1d YPHB/RX, was 4.2(g PHB/g residual biomass). The maximum accumulation percent of PHB to the final biomass was 81% when the ratio was higher than 67.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.23 no.3
• /
• pp.353-360
• /
• 1999

An investigation made of the variations of angle of bias on the top of the sleeve cap curve line and calculated easing contraction ratio by capheights(A ; a,h$\times$5,/6) B: A, H/4 +4cm C:A.H/3 D: A.H/ 4+3cm E:AH/4+2cm, F: A,H/4+1cm, G: A,H/4, H:A,H/6, I:A,H/8) and the efects of easing contraction on the cap curve lines of sleeve A, D, G by easing stitch density with the gathering foot: sewing condition-lockstitch industrial machine stitch density(N1.0 ; 38stitches/3cm N1.5: 26stitches/3cm, N2.0 ; 19stitches/3cm, N2.5 ; 14stitches/ 3cm) The results obtained were as follows; 1) The variations of the angle of bias on the top of the sleeve cap curve line by cap heights can be done according to the angle balance (front; $\alpha$-$\beta$ back ; $\alpha$'- $\beta$') between the angle (front ;$\alpha$, $\beta$, back ; $\alpha$'- $\beta$') of bias of the two base-lines. 2) The higher cap height the more higher the calculated easing contraction ratio. 3) The lower the stitch density the higher easing contraction ratio. 4) The effects of easing contraction was that sleeve G was more than sleeve A, D.

• Advances in concrete construction
• /
• v.10 no.2
• /
• pp.93-104
• /
• 2020

Basalt fiber is an eco-friendly fiber and comparatively newer to the world of fiber-reinforced polymer (FRP) composites. A limited number of studies have been reported in the literature on the strengthening of reinforced concrete (RC) beams with basalt fiber reinforced polymer (BFRP). The present experimental work explores the feasibility of using the BFRP strips for shear strengthening of the RC beams. The strengthening schemes include full wrap and U-wrap. A simple mechanical anchorage scheme has been introduced to prevent the debonding of U-wrap as well as to utilize the full capacity of the BFRP composite. The effect of varying shear span-to-effective depth (a/d) ratio on the behavior of shear deficient RC beams strengthened with BFRP strips under different schemes is examined. The RC beams were tested under a four-point loading system. The study finds that the beams strengthened with and without BFRP strips fails in shear for a/d ratio 2.5 and the enhancement of the shear capacity of strengthened beams ranges from 5% to 20%. However, the strengthened beams fail in flexure, and the control beam fails in shear for a higher a/d ratio, i.e., 3.5. The experimental results of the present study have been compared with the analytical study and found that the latter gives conservative results.

• Asian-Australasian Journal of Animal Sciences
• /
• v.3 no.3
• /
• pp.195-203
• /
• 1990

Thirty-six yearling (18 bulls, 18 heifers) swamp buffaloes (Bubalus bubalis) with average liveweight $177{\pm}26kg$, were randomly allotted to receive 6 dietary treatments according to a $2{\times}3$ factorial arrangement in a completely randomized design (CRD). Factor A assigned for two types of straw; untreated rice straw (RS) and urea-treated (5%, w/w) rice straw (UTS). Factor B assigned for three ratio of roughage to concentrate (R:C) at 80:20, 50:50 and 20:80. Feeding trial lasted for 9 months during which respective feeds were offered at 3% body weight and adjusted at bi-weekly intervals using corresponding liveweights. Parameters measured under this experiment were feed intake, ruminal fluid for pH, $NH_3-N$, volatile fatty acids (VFA), liveweight change at bi-weekly intervals, carcass characteristics and cost-net profit analysis. It was found that intakes and digestion coefficients of DM, OM, CP except NDF and ADF were improved appreciably when ratio of concentrate increased. The average daily gain (ADG) and feed conversion ratio (FCR) were highest in group fed urea-treated rice straw at R:C levels of 20:80 (551.2 g/d, 10.7 kg/kg) and 50:50 (542.3 g/d, 10.6 kg/kg). It was obvious that FCR was best in the group fed on urea-treated rice straw (13.8 kg/kg) as compared to untreated rice straw fed-group (24 kg/kg). Carcass compositions of buffaloes measured resulted in 48.2 dressing percentage in all treatments offered at R:C levels of 50:50 and 20:80, however, loin eye area were 46.0, 53.6, 50.0 and $54.0cm^2$ for RS and UTS at respective levels of R:C. It was notable that carcass fat content was low which resulted in higher content of lean meat particularly in group fed UTS at 50:50 ratio R:C. Simple cost-net profit analysis was performed, it was found that net profits were obtained as follows 27, 30, -47, 44, 58, 22 $US/hd for respective treatment groups of RS and UTS at respective R:C levels. As shown, the best net profit resulted in group fed UTS at 50:50 R:C level.

• Journal of Environmental Health Sciences
• /
• v.28 no.5
• /
• pp.93-101
• /
• 2002

We have studied that the prediction of desulfurization efficiency by limestone in fluidized-bed coal combustor. The results were presented as follows : Firstly, the bed temperature had a great deal of effect on the desulfurization and the optimum temperature of limestone was 85$0^{\circ}C$~90$0^{\circ}C$. Secondly, as the velocity and temperature increased, $K_{s}$, K and the desulfurization efficiency increased. So, $k_{s}$, $k_{d}$ highly depended on the air velocity and bed temperature, and $k_{s}$, $k_{d}$ were 82.53 mm/sec, 0.0041/sec at 0.2 m/sec, 85$0^{\circ}C$, $k_{s}$, $k_{d}$ were 125.62 mm/sec. 0.00532/sec at 0.3 m/sec, 80$0^{\circ}C$ respectively. And $k_{s}$, $k_{d}$ were 143.78 mm/sec, 0.00568/sec at 0.3 m/sec, 85$0^{\circ}C$. Thirdly, as a result of desulfurization modeling, there was good agreement between theory and experiments as anthracite fraction increased. At 3.0 of optimum Ca/S molar ratio, there was very good agreement between theory and experiments.riments.riments.s.

• Korean Chemical Engineering Research
• /
• v.61 no.4
• /
• pp.627-634
• /
• 2023

Graphitic carbon nitride (g-C₃N₄) has attracted considerable attention since its discovery for its catalysis of water splitting to hydrogen and oxygen under visible light irradiation. However, pristine g-C₃N₄ confers only low photocatalytic efficiency and requires surface cocatalysts to reach moderate activity due to a lack of accessible surface active sites. Inspired by the high specific surface area and superior electron transfer of graphene, we developed a strongly coupled binary structure of graphene and g-C₃N₄ aerogel with 3D porous skeleton. The as-prepared 3D structure photocatalysts achieve a high surface area that favors efficient photogenerated charge separation and transfer, enhances the light-harvesting efficiency, and significantly improves the photocatalytic hydrogen evolution rate as well. The photocatalyst performance is observed to be optimized at the ratio 3:7 (g-C₃N₄:GO), leading to photocatalytic H₂ evolution of 16125.1 mmol. g^-1. h^-1 under visible light irradiation, more than 161 times higher than the rate achieved by bulk g-C₃N₄.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.277-280
• /
• 2007

Field emission-back light unit (FE-BLU) was fabricated using carbon nanotube (CNT) emitter. Local dimming and local brightening techniques were achieved, which results in very high contrast ratio. In addition, the motion blur phenomenon, one of the serious problems of liquid crystal display (LCD) with cold cathode fluorescent lamp (CCFL)-BLU, was removed from LCD-TV by using FE-BLU.

• Ocean Systems Engineering
• /
• v.7 no.2
• /
• pp.143-155
• /
• 2017

For complex flexible structures such as nets, the determination of drag forces and its deformation is a challenging task. The accurate prediction of loads on cages is one of the key steps in designing fish farm facilities. The basic physics with a simple cage, can be addressed by the use of experimental studies. However, to design more complex cage system for various environmental conditions, a reliable numerical simulation tool is essential. In this work, the current load on a cage is calculated using a Morison-force model applied at instantaneous positions of equivalent-net modeling. Variations of solidity ratio ($S_n$) of the net and current speed are considered. An equivalent array of cylinders is built to represent the physical netting. Based on the systematic comparisons between the published experimental data for Raschel nets and the current numerical simulations, carried out using the commercial software OrcaFlex, a new formulation for $C_d$ values, used in the equivalent-net model, is presented. The similar approach can also be applied to other netting materials following the same procedure. In case of high solidity ratio and current speed, the hybrid model defines $C_d$ as a function of Re (Reynolds number) and $S_n$ to better represent the corresponding weak diffraction effects. Otherwise, the conventional $C_d$ values depending only on Re can be used with including shielding effects for downstream elements. This new methodology significantly improves the agreement between numerical and experimental data.