• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.50.1-50.1
• /
• 2011

Lead-free ceramics with a composition of 0.55 mol%$K_4CuNb_8O_23-(K_{1-x}Na_x)NbO_3$ (KCN-KNNx) where $0.45{\leq}x{\leq}0.60$ were synthesized by conventional ceramic processing. Results revealed that the addition of Na was effective in changing the microstructure and relative density of KCN-KNNx. Further, the addition of Na resulted in a slight shift of the phase transition temperatures (To-t and Tc) toward low values. A high mechanical quality factor (Qm) of 1850 was found atx=0.54, which might be due to the build-up of an internal bias field (Ei) within KCN. Thermal hysteresis in KNNx was confirmed with an increase in the Na content during the heating and cooling cycles, resulting from structural changes. Thus, KCN-KNNx with x=0.54 exhibits excellent piezoelectric properties with d33 (97 pC/N), kp (36%), and Qm (1850), being promising candidates for application in high-power piezoelectric devices.

• KSTLE International Journal
• /
• v.4 no.2
• /
• pp.56-59
• /
• 2003

Boron carbide thin coatings were deposited on silicon wafers by DC magnetron sputtering using a ${B}_4$C target with Ar as processing gas. Various amounts of methane gas (${CH}_4$) were added in the deposition process to better understand their influence on tribological properties of the coatings. Reciprocating wear tests employing an oscillating friction wear tester were performed to investigate the tribological behaviors of the coatings in ambient environment. The chemical characteristics of the coatings and worn surfaces were studied using X-ray Photoelectron Spectroscopy (XPS) and Auger Electron Spectroscopy (AES). It revealed that ${CH}_4$addition to Ar processing gas strongly affected the tribologcal properties of sputtered boron carbide coating. The coefficient of friction was reduced approximately from 0.4 to 0.1, and wear resistance was improved considerably by increasing the ratio of ${CH}_4$gas component from 0 to 1.2 vol %. By adding a sufficient amount of ${CH}_4$(1.2 %) in the deposition process, the boron carbide coating exhibited lowest friction and highest wear resistance.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.91-94
• /
• 2004

Preform design techniques have been investigated in efforts to reduce die wear and forming load and to improve material flow, filing ratio, etc. In hot forging processes, a thin deformed part of a workpiece, known as a flash, is formed in the narrow gap between the upper and lower tools. Although designers make tools that generate a flash intentionally in order to improve flow properties, excessive flash increases die wear and forming load. Therefore, it is necessary to make a preform shape that can reduce the excessive flash without changing flow properties. In this paper, a new preform design technique is proposed to reduce the excessive flash in a metal forging process. After a finite element simulation of the process is carried out with an initial billet, the flow of material in the flash region is traced from the final shape to the initial billet. The region belonging to the flash is then easily found in the initial billet. The finite element simulation is then carried out again with the modified billet from which the selected region has been removed. In several iterations of this technique, the optimal preform shape that minimizes the amount of flash without changing the forgeability can be obtained.

• The Journal of Engineering Research
• /
• v.8 no.1
• /
• pp.31-50
• /
• 2006

Shrinkage may cause cracking in concrete. In practice such cracking must be considered in most concrete applications because, under normal conditions, drying of the concrete is unavoidable, and when drying takes place shrinkage occurs. Cracked concrete is an inferior concrete because it is weaker, more permeable, and more susceptible to chemical attack. The development of the strength of LAC with aging depends on a few factors such as type of the cement, W/C ratio, curing conditions and periods. The higher the strength of LAC, the lower the possibility of shrinkage cracking. Hence, the strength of LAC in the hypocaust system depends to a large extent on the effect of cracking decrease of the antifoaming rate to drying shrinkage in cement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.259-264
• /
• 1999

The aim of this study of to compare the development of compressive strength of high-strength concrete with maturity and investigate the applicability the strength prediction models. An experiment was attempted on the high-strength concrete mixes using portland cement replaced by silica fume of 10% by weight of cement, the water-binder ratios of mixes being 0.30 and 0.35, the curing temperatures being 30, 20, 10, 5$^{\circ}C$. Test results of mixes are statistically analyzed to infer the correlation coefficient between the maturity and the compressive strength of high-strength concrete. The constant of strength prediction equation were determined from test results, and the equation was adopted to predict the strength of slab(W80$\times$D100$\times$H20cm). The slab was cast in the laboratory from the same batch water-binder ratio of 0.30, and cores were cut from slab in order to estimate the actual strength. These values are used to compare with predicted value. The present study allows more realistic determination of early age compressive strength of high-strength concrete and can be efficiently used to control the quality in actual construction.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.4C
• /
• pp.433-439
• /
• 2007

This paper derives an approximate expression for the output SINR(Signal to Interference plus Noise Ratio) of Applebaum type adaptive array under the scenario of the interferer's proximity to the desired signal. The approximation is made in terms of array geometry, the arrival direction of desired signal and that of an interfering signal. An interferer in the close proximity of target signal is shown to drastically impair the away performance. An approximate expression for interferer arrival direction which results in a predetermined performance loss is also obtained in terms of array configurations. Proposed approximation agrees with the computer calculated performance impairment when the two signals are apart by less than eight degrees. The allowable proximity of the interfering signal increases with the number of array elements.

• Journal of the Korean Ceramic Society
• /
• v.48 no.1
• /
• pp.40-45
• /
• 2011

In this study, the composition of optical glass for GMP(glass molding process) was designed with 'Design of Experiments' method. All the composition batch was performed by 'Create Factorial Design' method. Particularly, $SiO_2$, BaO and $Al_2O_3$ were chosen major parameters for investigating the effects of components on optical and thermal properties. BaO and $Al_2O_3$ strongly influenced on optical and thermal properties, respectively. Finally, the approximate values of desired optical and thermal values were obtained by microtuning of compositions. At the composition of $BaO:Al_2O_3:SiO_2$=10:4:48 (molar ratio), refractive index($n_d$) was 1.5833, coefficient of thermal expansion(CTE) was $104{\times}10^{-7}/^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04b
• /
• pp.45-48
• /
• 2002

Poly(3-hexylthiophene) or P3HT based organic thin film transistor (OTFT) array was fabricated on flexible poly carbonate substrates and the electrical characteristics were investigated. As the gate dielectric, a dual layer structure of polyimide-$SiO_2$ was used to improve the roughness of $SiO_2$ surface and further enhancing the device performance and also source-drain electrodes were $O_2$ plasma treated for improvement of the electrical properties, such as drain current and field effect mobility. For the active layer, polymer semiconductor, P3HT layer was printed by contact-printing and spin-coating method. The electrical properties of OTFT devices printed by both methods were evaluated for the comparison. Based on the experiments, P3HT-based OTFT array with field effect mobility of 0.02~0.025 $cm^{2}/V{\cdot}s$ and current modulation (or $I_{on}/I_{off}$ ratio) of $10^{3}\sim10^{4}$ was fabricated.

• Journal of Plant Biotechnology
• /
• v.6 no.2
• /
• pp.69-75
• /
• 2004

Optimal protocol for efficient genetic transformation has been defined to aid future strategies of genetic engineering in pigeon pea with agronomically important genes. Transgenic pigeonpea plants were successfully produced through Agrobacterium tumefaciens-mediated genetic transformation method using cotyledonary node explants by employing defined culture media. The explants were co-cultivated with A. tumefaciens strain C-58 harboring the binary plasmid, pCAMBIA-1301 [con-ferring $\beta$-glucuronidase(GUS) activity and resistance to hygromycin] and cultured on selection medium (regeneration medium supplemented with hygromycin) to select putatively transformed shoots. The shoots were then rooted on root induction medium and transferred to pots containing sand and soil mixture in the ratio of 1:1. About 22 putative TO transgenic plants have been produced. Stable expression and integration of the transgenes in the putative transgenics were confirmed by GUS assay, PCR and Southern blot hybridization with a transformation efficiency of over 45%. Stable integration and expression of the marker gene has been confirmed in the TO and T1 transgenics through PCR, and Southern hybridization.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.4
• /
• pp.8-14
• /
• 2006

The important function of Ball-Stop part is to operate power shift using suitable pneumatic force for vehicle with more than 5 ton when a driver changes gear. In this paper, we have applied the concept of the DFSS(Design for Six Sigma) to robust design of Ball-Stop part. First, we have found the control factors which could mainly influence the performance of the Ball-Stop part. The simulations of contact between head and detent pin was performed to evaluate effect of control factors according to DOE(Design of experiment) by using $ADAMS^{(R)}$. Finally, we have obtained optimal levels of each factors using $MINITAB^{(R)}$. Through the comparison of the result of optimized design with one of inintial design, we have verified the usefulness of DFSS method which can be applied to robust design of mechanical systems.