• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.328-332
• /
• 2010

In this study, porous ZnO sphere and Cu-ZnO composite were synthesized by coprecipitation method in diethylene glycol solvent. The physicochemical properties of as-prepared composite materials were characterized by SEM, XRD, $N_2$-sorption and $H_2$-TPR. A series of porous Cu-ZnO with different Cu contents (0, 6.6, 21.3, 36.4, 54.6, 77.8 wt%) was investigated for CO oxidation activity in a fixed bed reactor system. With increasing Cu content in Cu-ZnO the surface area and micropore volume of Cu-ZnO are decreased and Cu (36.4 wt%)-ZnO shows higher activity for CO oxidation compared to the others.

• Journal of the Korean Ceramic Society
• /
• v.44 no.6 s.301
• /
• pp.303-307
• /
• 2007

Transparent In-doped zinc oxide (IZO) thin films are deposited with variation of pulsed DC power at Ar atmosphere on coming 7059 glass substrate by pulsed DC magnetron sputtering. A c-axis oriented IZO thin films were grown in perpendicular to the substrate. The optical transmittance spectra showed high transmittance of over 80% in the UV-visible region and exhibited the absorption edge of about 350 nm. Also, the IZO films exhibited the resistivity of ${\sim}10^{-3}{\Omega}\;cm$ and the mobility of ${\sim}6cm/V\;s$. Organic Light-emitting diodes (OLEDs) with IZO/N,N'-diphenyl-N, N'-bis(3-methylphenl)-1, 1'-biphenyl-4,4'-diamine (TPD)/tris (8-hydroxyquinoline) aluminum ($Alq_3$)/LiF/Al configuration were fabricated. LiF layer inserted is used as an interfacial layer to increase the electron injection. Under a current density of $100\;mA/cm^2$, the OLEDs show an excellent efficiency (9.4 V turn-on voltage) and a good brightness ($12000\;cd/m^2$) of the emission light from the devices. These results indicate that IZO films hold promise for anode electrodes in the OLEDs application.

• Economic and Environmental Geology
• /
• v.33 no.5
• /
• pp.379-389
• /
• 2000

This study was focused on the investigation for the heavy metal contamination of soils derived from Yoecheon Industrial Complex in Chonnam Province. Total 201 soil samples including farmland, paddy, forest and playground soils were collected, extracted by 0.1N HCl and analyzed for Cd, Cu, Cr, Fe, Mn and Zn using AAS. Most pH values in soils were weak acidic ranges of 4-6, while some of them were over 8.0. Concentrations of Cd, Cu, Fe and Zn in the soils tend to be relatively high around the Au-Ag mine area, railroad stations and oil station, however, those of Cr, Mn and Pb show high at the northside of Pohang Steel Co (POSCO). Cadmium-Zn couples, and Cd-Zn and Zn-Cr couples have relatively good correlations in the farmland soils and paddy soils, respectively. Concentrations of Cd, Fe and Zn with depth tend to be higher in the top soils than in the bottom soils, but those of Cu and Pb do not show regular variations with depth.

• Applied Biological Chemistry
• /
• v.49 no.1
• /
• pp.21-24
• /
• 2006

A series of cytotoxic activities $(ED_{50})$ in vitro against six human cancers (lung cancer, uterine cancer, skin cancer, brain cancer, colon cancer and adenocarcinoma) and their seventeen cell lines of 3,6-bis(2'-pyridyl)pyridazine, 1, 3,6-bis-(6'-methyl-2'-pyridyl)pyridazine, 2 and their transition metal, Ni(II), Cu(II) and Zn(II) complexes, $3{\sim}6$ were measured. Particularly, the results revealed that the cytotoxic activities against the brain cancer cell line (SNB-19) and the colon cancer cell line (SW62) of bis- [3,6-bis-(6'-methyl-2'-pyridyl)pyridazine-$k^2N^2,N^3$]chlorocopper(II)perchlorate, 4 were shown to be higher than that of the first generation anticancer agent, Cis-platin.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.847-854
• /
• 1994

An amorphous single phase and coexistent amorphous and hcp-Mg phases in Mg-Zn-Ce system were found to form in the composition ranges of 20 to 40% Zn, 0 to 10% Ce and 5 to 20% Zn, 0 to 5% Ce, respectively. A $Mg_{85}Zn_{12}Ce_{3}$ amorphous alloy containing nanoscale hcp-Mg particles was found to form either by melt spinning or by heat treatment of melt -spun ribbon. The particle size of the hcp-Mg phase can be controlled in the range of 4 to 20 nm. The mixed phase alloy prepared thus has a good bending ductility and exhibits high ultimate tensile strength($\sigma_{B}$) ranging from 670 to 930 MPa and fracture elongation($\varepsilon_{f}$) of 5.2 to 2.0%. The highest specific strength($\sigma_{B}$/density =$\sigma_{s}$)$3.6 \times 10^5N \cdot m/kg$. It should be noted that the highest values of flB, US and ？1 are considerably higher than those (690MPa,$2.5 \times 10^5N \cdot m/kg$and 2.5%) for amorphous Mg-Zn-Ce alloys. The increase of the mechanical strengths by the formation of the mixed phase structure is presumably due to a dispersion hardening of the hcp supersaturated solution which has the hardness higher than that of the amorphous phase with the same composition.

• Journal of Korea Foundry Society
• /
• v.17 no.6
• /
• pp.592-597
• /
• 1997

The microstructure and tensile properties of Mg-Zn-Ca and Mg-Zn-Mn-Ca alloys have been investigated. The alloys were obtained by melting in a low carbon crucible coated with boron nitride under an Ar gas atmosphere to prevent oxidation and combustion. The Mg alloy melt was cast into the metallic mold at room temperature, and cooling part was located at the bottom of mold. The phase formed during solidification of the Mg-Zn-(Mn) alloys containing 0.5%Ca is $Ca_2Mg_6Zn_3$. The yield strength and ultimate tensile strength of the alloys increased with increasing Zn content, but the ductility did not change with increasing Zn content. The addition of Mn improves the yield strength and ultimate tensile strength of the alloys, but the ductility did not change. Tensile fracture of the alloys revealed brittle failure, with cracking along the $Ca_2Mg_6Zn_3$ phase. The variation of stress with strain obeyed the relationship of the ${\sigma}=K{\varepsilon}^n$.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.347-351
• /
• 2003

II-Ⅵ ZnO compound semiconductor thin films were grown on $\alpha$-Al$_2$O$_3$(0001) single crystal substrate by radical beam assisted molecular beam epitaxy and the optical properties were investigated. Zn(6N) was evaporated using Knudsen cell and O radical was assisted at the partial pressure of 1$\times$10$^{4}$ Torr and radical beam source of 250-450 W RF power. In $\theta$-2$\theta$ x-ray diffraction analysis, ZnO thin film with 500 nm thickness showed only ZnO(0002)and ZnO(0004) peaks is believed to be well grown along c-axis orientation. Photoluminescence (PL) measurement using He-Cd ($\lambda$=325 nm) laser is obtained in the temperature range of 9 K-300 K. At 9 K and 300 K, only near band edge (NBE) is observed and the FWHM's of PL peak of the ZnO deposited at 450 RF power are 45 meV and 145 meV respectively. From no observation of any weak deep level peak even at room temperature PL, the ZnO grains are regarded to contain very low defect density and impurity to cause the deep-level defects. The peak position of free exciton showed slightly red-shift as temperature was increased, and from this result the binding energy of free exciton can be experimentally determined as much as $58\pm$0.5 meV, which is very closed to that of ZnO bulk. By van der Pauw 4-point probe measurement, the grown ZnO is proved to be n-type with the electron concentration($n_{e}$ ) $1.69$\times$10^{18}$$cm^3$, mobility($\mu$) $-12.3\textrm{cm}^2$/Vㆍs, and resistivity($\rho$) 0.30 $\Omega$$\cdot$cm.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2003.05a
• /
• pp.26-26
• /
• 2003

산업 폐기물로서 전량 매립되고 있는 styrene monomer (SM) 공정에서 발생되는 산화철 폐촉매를 사용하여 NiZn-페라이트를 합성하였고, 그 자기적 특성을 조사하였다. 평균입경 0.5㎛로 미분쇄된 산화철 폐촉매에 NiO 및 ZnO를 혼합하여 900℃에서 하소한후 1230℃에서 5시간 동안 소결하여 스핀넬형 페라이트 소결체를 얻었다. Ni/sub x/Zn/ub 1-x/Fe₂O₄(x=0.36, 0.50, 0.66) 및 (Ni/sub 0.5/Zn/sub 0.5/)/sub 1-y/Fe/sub 2+y/O₄(y=-0.02, 0, 0.02) 조성에 대하여 초투자율을 측정하였다. S-parameter를 측정하여 반사 감쇄량을 계산하였다. Ni/sub 0.5/Zn/sub 0.5/fe₂O₄ 조성의 경우 밀도 5.38 g/㎤ kHz에서의 초투자율이 59인 특성을 얻었다. 산화철 폐촉매를 이용하여 X-band 주파수 영역에서 높은 전자파 흡수능을 갖는 전파흡수체를 제조할 수 있음을 확인하였다. Ni/sub 0.5/Zn/sub 0.5/Fe₂O₄ 조성에 대하여 1100℃에서 하소한 분말을 사용하여 실리콘 고무에 복합시킨 후 전파흡수능을 측정하였다. 폐촉매에는 산화철 이외에 CeO₂가 주된 첨가물로 함유되어 있어서 페라이트의 합성 후에도 2차상으로서 존재하였다. 출발 원료인 산화철 폐촉매에 존재하는 K₂O 및 CeO₂를 제거하기 위하여 산처리와 분산제를 이용한 CeO₂ 분리과정을 행하였다. 정제된 산화철 폐촉매에 NiO 및 ZnO를 혼합하여 900℃에서 하소하여 스핀넬형 페라이트를 합성하고 1325℃에서 5시간 소결하였다. 위와 마찬가지로 Ni/sub x/Zn/sub 1-x/Fe₂O₄(x=0.36, 0.50, 0.66)과 (Ni/sub 0.5/Zn/sub 0.5/)/sub 1-y/Fe/sub 2+y/O₄(y=-0.02, 0, 0.02) 조성에 대하여 자기적 특성을 조사하였다.화된 중성자빔으로 측정하였다 BPC-Si를 구부려 슬랩의 곡률반경을 변화시키면서 단색기-시료-검출기가 평행파 반평행배치일 때 Cu(111), (200), (220), (311), (331), (420)면의 회절선을 측정하여 각 조건에서 분해능과 강도를 평가하였다.료의 가시적 변화를 통해 illumination angle 1.25mrad(Dose rate : 334 × 10³ e/sup -//sec·n㎡)일 경우 약 3초 이내에 비정질화가 시작됨을 알 수 있었고 이는 약 1 × 10/sup 6/ e/sup -//sec·n㎡ 의 전자선량에 해당되며 이를 기준으로 각각의 illumination angle에 대한 임계전자선량을 평가할 수 있었다. 실질적으로 Cibbsite와 같은 무기수화물의 직접가열실험 시 전자빔 조사에 의해 야기되는 상전이 영향을 배제하고 실험을 수행하려면 illumination angle 0.2mrad (Dose rate : 8000 e/sup -//sec·n㎡)이하로 관찰하고 기록되어야 함을 본 자료로부터 알 수 있었다.운동횟수에 의한 영향으로써 운동시간을 1일 6시간으로 설정하여, 운동횟수를 결정하기 위하여 오전, 오후에 각 3시간씩 운동시키는 방법과 오전부터 6시간동안 운동시키는 두 방법을 이용하여 품질을 비교하였다. 각 조건에 따라 운동시킨 참돔의 수분함량을 나타낸 것으로, 2회(오전 3시간, 오후 3시간)에 나누어서 운동시키기 위한 육의 수분함량은 73.37±2.02%를 나타냈으며, 1회(6시간 운동)운동시키기 위한 육은 71.74±1.66%을 나타내었다. 각각의 운동조건에서 양식된 참돔은 사육초기에는 큰 변화가 없었으나, 사육 5일 이후에는 수분함량이 증가하여 15일에는 76.40±0.14, 75.62±0.98%의 수분함량을 2회와 1회 운동시킨 참돔의 육에서 각각 나타났다. 운동횟수에 따른 지질함량은 2회 운동시킨 참돔은 5.83±2.08, 1회 운

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.4
• /
• pp.336-347
• /
• 1985

Soils and rice plants subject to smoke from the Jang-hang Smelter were samples at two depths to assess the nature and extend of Cd, Cu, Pb, and Zn contamination, particularly with respect to distance from pollution source. Soils at east site within 1km of the center of the smelter were highly contaminated with Cd, Cu, Pb, and Zn. Metal levels in the smoke-polluted area were higher in surface soil than in subsurface soil, and decreased rapidly with distance reaching nearly background levels at 5km from pollution source. A position correlation was found between contents of total and 0.1 N HCl-extractable, or 1.0N $CH_3COONH_4$- extractable heavy metals in surface soils of pollution. Contents of heavy metals in soils were positively correlated with soil organic matter and cation exchange capacity. The contents of heavy metals in brown rice collected from the paddy field around the Jang-hang Smelter were in the range of 0.23-1.33 ppm for Cd, 2.39-6.25 for Cu, 0.95-8.32 ppm for Pb and 14.60-27.31 for Zn. The contents of Cd, Cu, and Zn in rice straw were positively correlated with those in the brown rice. Negative correlation was found between the contents of Cd, Cu, Pb, and Zn in brown rice and the distance from the source.

• Korean Journal of Materials Research
• /
• v.4 no.1
• /
• pp.90-96
• /
• 1994

ZnO thin films were deposited using Diethylzinc and $N_{2}O$ gas by plasma enhanced CVD (PECVD) at low substrate temperatures below $300^{\circ}C$. The effect of deposition parameters on the growth rate and the structural properties was determined at various deposition conditions. Crystallized ZnO thin films were successfully deposited even at $150^{\circ}C$ of substrate temperature. Above $200^{\circ}C$ c-axis oriented ZnO thin films, of which a standard deviation of X-ray rocking curve was less than $6^{\circ}$. were deposited on glass substrates. The variation of deposition rate showed different trends depending on substrate temperature and rf-input power. According to the deposition rate behavior as a function of substrate temperature, the transition points were observed resulting from crystallization of ZnO thin films. The activation energies for the deposition of ZnO thin films were 3.1KJ/mol and 1.9KJ/mol for the rf powers of 200W and 250W, respectively.