• Korean Journal of Materials Research
• /
• v.1 no.1
• /
• pp.37-45
• /
• 1991

In order to control the microstructures, the sintering behavior and abnormal grain growth with Ba/Ti ratio variation of $BaTiO_3$were investigated. The $BaTiO_3$powders used in this study were prepared by conventional calcination of $BaCO_3$ and $TiO_2$. The onset temperatures of the sintering were lowered and the densification was enhanced with increasing amounts of $TiO_2$ excess. These results are because of decrease of calcined particle sizes. A eutectic melt above temperature of $1320^{\circ}C$ did not assist the densification. Grain growth was strongly inhibited with increasing amounts of $TiO_2$ excess. The inhibition of grain growth caused abnormal grain growth due to inhomogeneous distribution of Ti-rich second phase.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.402-405
• /
• 2001

The BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics were prepared by conventional mixed oxide method. The structural and dielectric properties of the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics with the sintering temperature were investigated. Increasing the sintering temperature, the 2$\theta$ value of BaTiO$_3$peaks were shifted to the higher degree and intensity of the BaTiO$_3$and BaNbO$_3$peaks were increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 135$0^{\circ}C$ and 1375$^{\circ}C$, the grain was fine and uniform. Increasing the sintering temperature, the pore was decreased and the dielectric constant was increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 1375$^{\circ}C$, the dielectric constant and dielectric loss were 5424, 0.02 respectively.ctively.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1491-1493
• /
• 2002

The 0.5$Ba_2Ti_9O_{20}$-0.5Mg$TiO_3$ ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature by XRD. According to the X-ray diffraction patterns, major phases of the 0.5$Ba_2Ti_9O_{20}$-0.5Mg$TiO_3$ ceramics were coexisted. Also the secondary phase of Mg$Ti_2O_5$, Ba$Mg_6Ti_6O_{19}$ and the unreacted $TiO_2$ phase were existed. In the case of 0.5$Ba_2Ti_9O_{20}$-0.5Mg$TiO_3$ ceramics sintered $1350^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 33.7, 54,900GHz, -12.5ppm/$^{\circ}C$, respectively.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.383-386
• /
• 1998

The microwave dielectric properties and sintering properties of the xCaTi $O_{3}$-yMgTi $O_{3}$-z(L $i_{1}$2/N $d_{1}$2/)Ti $O_{3}$ systems were investigated for the development of microwave dielectric materials. Dielectric constants decreased with increasing the amounts of MgTi $O_{3}$ and increased with reducing the amounts of MgTi $O_{3}$ and increased with reducing (L $i_{1}$2/N $d_{1}$2/)Ti $O_{3}$ contents. The microscopic structures were mixed phase with a little second phase. We found some compositions with .tau.$_{f}$ changed from positive to negative value with increasing MgTi $O_{3}$ or (L $i_{1}$2/N $d_{1}$2/)Ti $O_{3}$ contents. The microscopic strucstures were mixed phase with a little second phase. We found some compositions with .tau.$_{f}$ =0ppm/.deg.C. these compmsitions exhibited the stable dielectric properties on the various sintering temperatures.res.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1011-1016
• /
• 2000

The (1-x)MgTi $O_3$-xSrTi $O_3$(x=0.02~0.08) ceramics were fabricated by the conventional mixed oxide method. The sintering temperature and time were 125$0^{\circ}C$~1375$^{\circ}C$ and 2hours. The structure and microwave dielectric properties were investigated with sintering temperature and composition ratio. From the X-ray diffraction patterns, the cubic SrTi $O_3$and hexagonal MgTi $O_3$structures were coexisted in the (1-x)MgTi $O_3$-xSrTi $O_3$(x=0.02~0.08) ceramics. The dielectric constant($\varepsilon$$_{r}$) was increased and the temperature coefficient of resonant frequency($\tau$$_{f}$)was decreased with addition of SrTi $O_3$. The temperature coefficient of resonant frequency($\tau$$_{f}$) was gradually varied from negative value to positive value with increasing SrTi $O_3$. In the case of 0.96MgTi $O_3$-0.04SrTi $O_3$ceramics sintered at 130$0^{\circ}C$, the dielectric constant, quality factor and temperature coefficient of resonant frequency were 20.5, 5918(at 7.33GHz) and +10ppm/$^{\circ}C$, respectively.y.y.y.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.5-8
• /
• 2004

전자빔 증착법 (e-beam evaporation)를 이용하여 $TiO_2$ 박막과 $Al_2O_3/TiO_2$ 이중박막을 제조한 후, $800^{\circ}C$ 공기 중에서 열처리하여, 알루미나 층의 유무에 따른 두 박막의 전기전도 특성과 100 ppm CO 가스에 대한 반응 특성을 고찰하였다. 알루미나 층이 증착되지 않은 순수한 $TiO_2$ 박막의 전기 전도도 (in dry air)는 $100^{\circ}C-500^{\circ}C$ 온도범위에서 온도가 증가함에 따라 증가하였으며 알루미나 층이 증착된 $Al_2O_3/TiO_2$ 이중막보다 높은 전도도를 나타내고 있으나, 약 $300^{\circ}C$이상의 온도에서는 $Al_2O_3/TiO_2$ 이중막의 전기 전도도가 급격히 증가하여 $TiO_2$ 박막의 전기전도도 보다 더 높은 값을 나타내었다. 또한 온도에 따른 CO 가스 감도(sensitivity)는 $TiO_2$ 박막의 경우 $400^{\circ}C$까지는 서서히 증가하여 그 이상의 온도에서 급격히 감소하였으나, $Al_2O_3/TiO_2$ 이중막은 $250^{\circ}C$에서 감도가 급격히 증가하여 최대값을 나타내었으며, $350^{\circ}C$에서 감도가 급격히 감소하는 특성을 나타내었다.

• Journal of the Korean Chemical Society
• /
• v.9 no.2
• /
• pp.71-74
• /
• 1965

Reduction of Ti(Ⅳ)-oxalate complex on dropping mercury electrode has been studied as a function of oxalate concentration and of pH varied with HCl. Assuming there are equilibrium $TiO(C_2O_4)_2= \;+\;2H^+\;=\;Ti^{+4}\;+\;2C_2O_4\;=\;+\;H_2O,\;K_4$ in addition to $TiO(C_2O_4)_2\;^=\;=\;TiO^{++}\;+\;2C_2O_4=\;K_2\;Ti(C_2O_4)_2\;^-\;=\;Ti^{+3}\;+\;2C_2O_4=\;K_3$ in the system cathodic wave has been well explained for that pH is higher than 0.5. The equilibrium constants $K_2,\;K_3$ and $K_4$ have been to be $2{\times}10^{-12},\;5{\times}10^{-13}$ and $10^{-11}$, respectively. The reduction of Ti(Ⅳ)-oxalate system is $Ti^{+4}\;+\;e\;{\to}\;Ti^{+3}$ in the concentration of hydrochloric acid, higher than 3M.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.2 s.31
• /
• pp.1-9
• /
• 2004

We investigated the effect of $BaTiO_3$ powder content on the dielectric constant of epoxy/$BaTiO_3$ composite embedded capacitor films (ECFs). Variations of the dielectric constant of epoxy/$BaTiO_3$ composite ECFs with unimodal $BaTiO_3$ powder content were measured. To explain this result, density of the ECFs was measured, and surface and cross section images of the ECFs were observed. In addition, variations of the dielectric constant of epoxy/$BaTiO_3$ composite ECFs with various bimodal combinations were measured. In the case of unimodal powder, the maximum dielectric constant was about 60 at $60\;vol\%$ S4 powder. And more powder addition lowered the dielectric constant of the ECFs, which was due to voids or pores formation by excess $BaTiO_3$ powder. In the case of bimodal combination, $75vol\%\;BaTiO_3$ powder loading and the dielectric constant of 90 were achieved using $S_5+C_1$ combination, biggest and smallest powder combination.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.7
• /
• pp.1051-1054
• /
• 2004

The structural transformation behavior of $Na_2Ti_3O_7$ by hydrolysis was investigated in mild and strong acidic aqueous medium. Compared with $K_2Ti_4O_9,\;Na_2Ti_3O_7$ exhibits quite different structural and morphological transformation behavior despite their similar layered structural characteristics. $TiO_2(B)$ obtained by heat treatment of $H_2Ti_3O_7\;at\;350^{\circ}C$ transforms to rutile $H_2Ti_3O_7\;at\;900^{\circ}C$. This temperature is much lower than $1200{\circ}C$, the temperature for anatase to rutile transition when $K_2Ti_4O_9$ is used as a starting titanate. A rectangular rod shape and size of $TiO_2(B)$ particles obtained from $Na_2Ti_3O_7$ is also different from a fibrous structure of $TiO_2(B)$ prepared using $K_2Ti_4O_9$. Rutile crystals of 100 nm diameter with a corn-like morphology and large surface area are directly obtained when the hydrolysis of $Na_2Ti_3O_7$ is carried out at $100^{\circ}C$ in a strong acid solution. The structure of starting titanates and the hydrolysis conditions are an important factor to decide the particle size and morphology of $TiO_2(B)\;and\;TiO_2$.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1108-1112
• /
• 2002

pellets were fabricated as a reactor control material by the powder process. Sinterability of $Dy_2O_3+TiO_2$ mixtures and phases of solid solutions were analyzed by using TMA and XRD, respectively. The thermal conductivity of pellet was determined from the measurement data of the specific heat and the thermal diffusivity of the pellet. The sinterability and the sintered density varied as a function of Dy content in $Dy_xTi_yO_z$. The pellet of $3\;g\;Dy/cm^3\;Dy_xTi_yO_z$ melted in the sintering temperature of $1580{\circ}C$. There were two phases of $Dy_2TiO_5+Dy_2Ti_2O_7$ and a single phase of $Dy_2TiO_5$ for the pellet that has the Dy content of and , respectively. The thermal conductivity of $Dy_xTi_yO_z$ was nearly constant in the temperature range of $25~600{\circ}$. It was 1.69~1.78 W/mK for the pellet sintered in and 1.49~1.55 W/mK for the pellet sintered in $1550{\circ}$.