• 한국물환경학회지
• /
• 제32권5호
• /
• pp.403-409
• /
• 2016

In this study, a TiO₂ nanotube was grown on a titanium plate by using anodic oxidation method for the evaluation of TiO₂ nanotube morphology. The TiO₂ nanotube was grown in an electrolyte containing ethylene glycol, 0.2 wt% of NH₄F and 2 vol% of H₂O. Applied voltage varied from 30 to 70 V and the morphology of the TiO₂ nanotube was observed. After anodization, a TiO₂ nanotube plate was immersed in 35℃ ethanol for 24 hours. Anatase and rutile crystal forms of TiO₂ nanoutbe were observed after annealing. 4-chrolobenzoic acid, a probe compound for OH radicals, was dissolved in H₂O in order to measure the OH radical. Liquid chromatography was used to check the concentration of the 4-chrolobenzoic acid. The OH radical generation by TiO₂ nanotube plate was proportionate to the length of the TiO₂ nanotube. Furthermore, when the number of TiO₂ nanotube plate increased, the OH radical generation increased as well.

• 한국물환경학회지
• /
• 제35권6호
• /
• pp.550-556
• /
• 2019

This study was carried out to improve the photocatalytic reaction of TiO₂ photocatalyst. During the photocatalytic reaction, OH radicals are generated and they have an excellent oxidation capability for wastewater treatment. To evaluate the OH radicals generated according to crystallographic structure of TiO₂ nanotubes photocatalyst, a probe compound, 4-Chlorobenzoic acid was monitored to evaluate OH radical. Ultraviolet light was applied for photocatalytic reaction of TiO₂. The 4-Chlorobenzoic acid solution was prepared at laboratory. TiO₂ nanotube was grown on titanium plate by using anodization method. The annealing temperature for TiO₂ nanotube was varied from 400 to 900 ℃ and the crystal forms of the TiO₂ nanotube was analyzed. Depending on annealing temperature, TiO₂ nanotubes have shown different crystal forms; 100% anatase (0 % rutile), 18.4 % rutile (81.6 % anatase), 36.6 % rutile (63.4 % anatase) and 98.6% rutile (1.4% anatase). As the annealing temperature increases, the rutile ratio increases. OH radical generation from 18.4 % rutile TiO₂ nanotube plate was about 3.8 times higher than before annealing and 1.4 times higher than only 100 % anatase-TiO₂ nanotube. The efficiency of the 18.4% rutile TiO₂ nanotube was the best in comparison to TiO₂ nanotube with 18.4 %, 36.6 % and 98.6 % rutile. As a result, photocatalytic ability of 18.4 % rutile-TiO₂ nanotube plate was higher than 100 % anatase-TiO₂ nanotube plate.

• 한국물환경학회지
• /
• 제35권5호
• /
• pp.418-424
• /
• 2019

In this study, $TiO_2$ nanotubes with different morphologies were prepared in the electrolyte consisting of ethylene glycol, ammonium fluoride($NH_4F$), and deionized water($H_2O$) by controlling the voltage and time in the anodization method. Thicknesses and pore sizes of these $TiO_2$ nanotubes were measured to interpret the relationship between anodization conditions and $TiO_2$ nanotube morphologies. Element contents in the $TiO_2$ nanotubes were detected for further analysis of $TiO_2$ nanotube characteristics. Photoelectrolyticdecolorization efficiencies of the $TiO_2$ nanotube plates with various morphologies were tested to clarify the morphology that a highly active $TiO_2$ nanotube plate should have. Influences of applied voltage in photoelectrolysis processes and sodium sulfate($Na_2SO_4$) concentration in wastewater on the decolorization efficiency were also studied. To save the equipment investment cost in photoelectrolysis methods, a two-photoelectrode system that uses the $TiO_2$ nanotube plates as photoanode and photocathode instead of adding other counter electrodes was studied. Compared with single-photoelectrode system that uses the $TiO_2$ nanotube plate as photoanode and titanium plate as cathode on the view of the treatment of dye wastewater containing different amounts of salt. As a result, a considerably suitable voltage was strictly needed for enhancing the photoelectrolyticdecolorization effect of the two-photoelectrode system but if salts exist in wastewater, an excellent increase in the decolorization efficiency can be obtained.

• 한국응용과학기술학회지
• /
• 제35권3호
• /
• pp.612-621
• /
• 2018

본 연구에서는 전기분해 방법을 이용한 질산성질소($NO_3{^-}-N$) 분해가 $TiO_2$ nanotube plate 및 구리, 니켈, 스테인리스 스틸, 알루미늄, 주석, 티타늄을 환원전극으로 사용하였을 때 가능한지를 평가하였다. 전극의 전기화학적 특성 평가는 임피던스 측정을 하여 비교하였고, $TiO_2$ nanotube plate의 표면 분석은 주사전자현미경을 통해 SEM 및 BET 분석법을 이용한 비표면적 분석을 통해 비교하였다. 질산성질소 전해실험의 경우 90분의 실험을 진행하였으며, 실험 결과 전극 표면의 부식이 수반되지 않은 $TiO_2$ nanotube plate가 기타 금속 전극에 비해 질산성질소 환원 반응속도가 가장 뛰어난 것으로 확인되었다.

• 한국응용과학기술학회지
• /
• 제34권2호
• /
• pp.349-356
• /
• 2017

본 연구에서는 $TiO_2$ nanotube 광촉매의 고도산화처리능을 비교하기 위해서 OH 라디칼 생성력을 평가하고자 하였다. 자외선 조사에 따른 Probe compound인 4-Chlorobenzoic acid (pCBA)의 농도 감소에 따라 OH radical 생성량을 산정하는 방법으로 광촉매 효율을 평가하였는데, $TiO_2$ nanotube 표면에서의 전자의 흐름을 원활하게 하기 위하여 전기적 에너지를 주었을 시 광촉매 효율의 증가 가능성 또한 확인하고자 자외선 조사 시 전류밀도를 인가하는 방법으로 실험을 진행하였다. 실험에 사용된 $TiO_2$ nanotube는 전극효과를 부여하기 위해 양극산화법으로 티타늄판을 이용하여 제조하였으며, pCBA 용액에는 전도도를 부여하기 위하여 NaCl을 첨가하여 전해질로 사용하였다. 정전류 정전압 조건하에서 자외선조사 실험을 진행하였으며, 전류가 흐르는 광촉매에 자외선 조사 시 OH 라디칼 생성량은 광촉매 없이 자외선만 조사하였을 때에 비해 약 5.6배, $TiO_2$ 광촉매와 함께 자외선을 조사하였을 보다 약 2.2배 증가하였다. 결과적으로 광촉매반응에 전기적 에너지를 부여하였을 시 시너지효과를 가져올 수 있는 가능성을 확인할 수 있었다.

• 한국물환경학회지
• /
• 제31권4호
• /
• pp.360-366
• /
• 2015

In this study $TiO_2$ nanotube was grown on Ti by anodic oxidation to be used as a photocatalyst. The growth and formation of $TiO_2$ nanotube was monitored during anodization in ethylene glycol electrolyte by changing voltage and composition of electrolyte. Commercially available titanium plate (purity>99.8%, thickness:1mm) Applied voltage and concentration of $NH_4F$ and $H_2O$ were varied to find the optimum condition. Applied voltage is important to make $TiO_2$ nanotube and the electrolyte containing ethylene glycol, 0.2 wt% $NH_4F$ and 2 vol% $H_2O$ was confirmed to be the optimum conditions for the formation and growth of $TiO_2$ nanotubes.

• 한국재료학회지
• /
• 제32권1호
• /
• pp.14-22
• /
• 2022

To improve light absorption ability in the visible light region and the efficiency of the charge transfer reaction, Pd nanoparticles decorated with reduced TiO₂ nanotube photocatalyst were synthesized. The reduced TiO₂ nanotube photocatalyst was fabricated by anodic oxidation of Ti plate, followed by an electrochemical reduction process using applied cathodic potential. For TiO₂ photocatalyst electrochemically reduced using an applied voltage of -1.3 V for 10 min, 38% of Ti⁴⁺ ions on TiO₂ surface were converted to Ti³⁺ ion. The formation of Ti³⁺ species leads to the decrease in the band gap energy, resulting in an increase in the light absorption ability in the visible range. To obtain better photocatalytic efficiency, Pd nanoparticles were decorated through photoreduction process on the surface of reduced TiO₂ nanotube photocatalyst (r10-TNT). The Pd nanoparticles decorated with reduced TiO₂ nanotube photocatalyst exhibited enhanced photocurrent response, and high efficiency and rate constant for aniline blue degradation; these were ascribed to the synergistic effect of the new electronic state of the TiO₂ band gap energy induced by formation of Ti³⁺ species on TiO₂, and by improvement of the charge transfer reaction.

• 한국표면공학회지
• /
• 제43권1호
• /
• pp.25-30
• /
• 2010

Titanium and titanium alloys are widely used for orthopedic and dental implants for their superior mechanical properties, low modulus, excellent corrosion resistance and good biocompatibility. In this study, corrosion behaviors of nanotube formed on the bone plate of Ti-6Al-4V alloy for dental use have been investigated. $TiO_2$ nanotubes were formed on the dental bone plates by anodization in $H_3PO_4$ containing 0.6 wt % NaF solution at $25^{\circ}C$. Electrochemical experiments were performed using a conventional three-electrode configuration with a platinum counter electrode and a saturated calomel reference electrode. Anodization was carried out using a scanning potentiostat (EG&G Co, Model 263A USA), and all experiments were conducted at room temperature. The surface morphology was observed using field emission scanning electron microscopy (FE-SEM) and energy dispersive x-ray spectroscopy(EDS). The corrosion behavior of the dental bone plates was examined using potentiodynamic test(potential range of -1500~2000 mV) in a 0.9% NaCl solution by potentiostat (EG&G Co, PARSTAT 2273. USA). The inner diameter of nanotube was about 150~180 nm with wall thickness of about 20 nm. The interspace of nanotube to nanotube was 50 nm. The passive region of the nanotube formed bone plates showed the broad range compared to non-nanotube formed bone plates. The corrosion surface of sample was covered with corrosion products.

• 한국재료학회지
• /
• 제23권4호
• /
• pp.240-245
• /
• 2013

Electrochemical surface treatment is commonly used to form a thin, rough, and porous oxidation layer on the surface of titanium. The purpose of this study was to investigate the formation of nanotubular titanium oxide arrays during short anodization processing. The specimen used in this study was 99.9% pure cp-Ti (ASTM Grade II) in the form of a disc with diameter of 15 mm and a thickness of 1 mm. A DC power supplier was used with the anodizing apparatus, and the titanium specimen and the platinum plate ($3mm{\times}4mm{\times}0.1mm$) were connected to an anode and cathode, respectively. The progressive formation of $TiO_2$ nanotubes was observed with FE-SEM (Field Emission Scanning Electron Microscopy). Highly ordered $TiO_2$ nanotubes were formed at a potential of 20 V in a solution of 1M $H_3PO_4$ + 1.5 wt.% HF for 10 minutes, corresponding with steady state processing. The diameters and the closed ends of $TiO_2$ nanotubes measured at a value of 50 cumulative percent were 100 nm and 120 nm, respectively. The $TiO_2$ nanotubes had lengths of 500 nm. As the anodization processing reached 10 minutes, the frequency distribution for the diameters and the closed ends of the $TiO_2$ nanotubes was gradually reduced. Short anodization processing for $TiO_2$ nanotubes of within 10 minutes was established.

• E2M - 전기 전자와 첨단 소재
• /
• 제12권7호
• /
• pp.7-11
• /
• 1999

Fully sealed field emission display in size of 4.5 inch has been fabricated using single-wall carbon nanotubes-organic vehicle com-posite. The fabricated display were fully scalable at low temperature below 415$^{\circ}C$ and CNTs were vertically aligned using paste squeeze and surface rubbing techniques. The turn-on fields of 1V/${\mu}{\textrm}{m}$ and field emis-sion current of 1.5mA at 3V/${\mu}{\textrm}{m}$ (J=90${\mu}{\textrm}{m}$/$\textrm{cm}^2$)were observed. Brightness of 1800cd/$m^2$ at 3.7V/${\mu}{\textrm}{m}$ was observed on the entire area of 4.5-inch panel from the green phosphor-ITO glass. The fluctuation of the current was found to be about 7% over a 4.5-inch cath-ode area. This reliable result enables us to produce large area full-color flat panel dis-play in the near future. Carbon nanotubes (CNTs) have attracted much attention because of their unique elec-trical properties and their potential applica-tions [1, 2]. Large aspect ratio of CNTs together with high chemical stability. ther-mal conductivity, and high mechanical strength are advantageous for applications to the field emitter [3]. Several results have been reported on the field emissions from multi-walled nanotubes (MWNTs) and single-walled nanotubes (SWNTs) grown from arc discharge [4, 5]. De Heer et al. have reported the field emission from nan-otubes aligned by the suspension-filtering method. This approach is too difficult to be fully adopted in integration process. Recently, there have been efforts to make applications to field emission devices using nanotubes. Saito et al. demonstrated a car-bon nanotube-based lamp, which was oper-ated at high voltage (10KV) [8]. Aproto-type diode structure was tested by the size of 100mm $\times$ 10mm in vacuum chamber [9]. the difficulties arise from the arrangement of vertically aligned nanotubes after the growth. Recently vertically aligned carbon nanotubes have been synthesized using plasma-enhanced chemical vapor deposition(CVD) [6, 7]. Yet, control of a large area synthesis is still not easily accessible with such approaches. Here we report integra-tion processes of fully sealed 4.5-inch CNT-field emission displays (FEDs). Low turn-on voltage with high brightness, and stabili-ty clearly demonstrate the potential applica-bility of carbon nanotubes to full color dis-plays in near future. For flat panel display in a large area, car-bon nanotubes-based field emitters were fabricated by using nanotubes-organic vehi-cles. The purified SWNTs, which were syn-thesized by dc arc discharge, were dispersed in iso propyl alcohol, and then mixed with on organic binder. The paste of well-dis-persed carbon nanotubes was squeezed onto the metal-patterned sodalime glass throuhg the metal mesh of 20${\mu}{\textrm}{m}$ in size and subse-quently heat-treated in order to remove the organic binder. The insulating spacers in thickness of 200${\mu}{\textrm}{m}$ are inserted between the lower and upper glasses. The Y\ulcornerO\ulcornerS:Eu, ZnS:Cu, Al, and ZnS:Ag, Cl, phosphors are electrically deposited on the upper glass for red, green, and blue colors, respectively. The typical sizes of each phosphor are 2~3 micron. The assembled structure was sealed in an atmosphere of highly purified Ar gas by means of a glass frit. The display plate was evacuated down to the pressure level of 1$\times$10\ulcorner Torr. Three non-evaporable getters of Ti-Zr-V-Fe were activated during the final heat-exhausting procedure. Finally, the active area of 4.5-inch panel with fully sealed carbon nanotubes was pro-duced. Emission currents were character-ized by the DC-mode and pulse-modulating mode at the voltage up to 800 volts. The brightness of field emission was measured by the Luminance calorimeter (BM-7, Topcon).