• Korean Journal of Materials Research
• /
• v.31 no.2
• /
• pp.92-96
• /
• 2021

We report the growth and enhanced photoelectrochemcial (PEC) water-splitting reactivity of few-layer MoS2 nanosheets on TiO2 nanowires. TiO2 nanowires with lengths of ~1.5 ~ 2.0 ㎛ and widths of ~50~300 nm are synthesized on fluorine-doped tin oxide substrates at 180 ℃ using hydrothermal methods with Ti(C4H9O)4. Few-layer MoS2 nanosheets with heights of ~250 ~ 300 nm are vertically grown on TiO2 nanowires at a moderate growth temperature of 300 ℃ using metalorganic chemical vapor deposition. The MoS2 nanosheets on TiO2 nanowires exhibit typical Raman and ultraviolet-visible light absorption spectra corresponding to few-layer thick MoS2. The PEC performance of the MoS2 nanosheet/TiO2 nanowire heterostructure is superior to that of bare TiO2 nanowires. MoS2/TiO2 heterostructure shows three times higher photocurrent than that of bare TiO2 nanowires at 0.6 V. The enhanced PEC photocurrent is attributed to improved light absorption of MoS2 nanosheets and efficient charge separation through the heterojunction. The photoelectrode of the MoS2/TiO2 heterostructure is stably sustained during on-off switching PEC cycle.

• Journal of Sensor Science and Technology
• /
• v.20 no.5
• /
• pp.305-310
• /
• 2011

This study focuses on the fabrication of $TiO_2$ nanosheets and their gas sensor application. A simple sonochemical method is employed to fabricate the $TiO_2$ nanosheets. The obtained samples were investigated by transmission electron microscope(TEM) and X-ray Diffraction(XRD). The $TiO_2$ nanosheets were coated on substrates by a dropping method followed by heat treatment. The sensor responses to volatile organic compounds(VOCs) such as toluene, benzene, ethanol and acetaldehyde were studied. It was found that the $TiO_2$ nanosheets sensors are able to detect ppb-levels of VOC gases.

• Nano
• /
• v.13 no.11
• /
• pp.1850129.1-1850129.10
• /
• 2018

To improve the high charge carrier recombination rate and low visible light absorption of {001} facets exposed $TiO_2$ [$TiO_2(001)$] nanosheets, few-layered $MoS_2$ nanoparticles were loaded on the surfaces of $TiO_2(001)$ nanosheets by a simple photodeposition method. The photocatalytic activities towards Rhodamine B (RhB) were investigated. The results showed that the $MoS_2-TiO_2(001)$ nanocomposites exhibited much enhanced photocatalytic activities compared with the pure $TiO_2(001)$ nanosheets. At an optimal Mo/Ti molar ratio of 25%, the $MoS_2-TiO_2(001)$ nanocomposites displayed the highest photocatalytic activity, which took only 30 min to degrade 50 mL of RhB (50 mg/L). The active species in the degradation reaction were determined to be $h^+$ and $^{\bullet}OH$ according to the free radical trapping experiments. The reduced charge carrier recombination rate, enhanced visible light utilization and increased surface areas contributed to the enhanced photocatalytic performances of the 25% $MoS_2-TiO_2(001)$ nanocomposites.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.6
• /
• pp.289-294
• /
• 2017

Films fabricated using atomic layer 2-dimensional nanosheets exhibit various physical properties depending on the size of the nanosheet. This is because the physical properties of the film depend on the interfacial properties between the sheets. Therefore, the synthesis of large-sized nanosheets is very important because it can reduce the dependency of the film on the interfacial properties. In this study, we succeeded in fabricating $TiO_x$ nanosheets with atomic layer thickness over micrometer size by using single-crystallized starting material and its chemical exfoliation. In addition, it was revealed that the mechanical agitation speed (the stirring speed of a magnetic bar) during the exfoliation step using the organic material is closely related to the nanosheet size and the colloidal concentration of the nanosheets.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.1
• /
• pp.14-19
• /
• 2013

We have successfully synthesized $Bi_{4-x}La_xTi_3O_{12}$ (x~2) having Aurivillius-type layered perovskite structure from exfoliated layered perovskite oxide of $K_2La_2Ti_3O_{10}$ with Ruddlesden-Popper structure. The reaction between the exfoliated lanthanum titanate nanosheets and BiOCl nanocrystal resulted in the formation of polycrystalline $Bi_{4-x}La_xTi_3O_{12}$ (x~2) after heating above $700^{\circ}C$. Colloidal suspension of the nanosheets could be obtained by intercalating ethylamine (EA) into the protonated lanthanum titanate, $H_2La_2Ti_3O_{10}$, derived from $K_2La_2Ti_3O_{10}$. Transmission electron microscopic (TEM) analysis show that the exfoliated lanthanium titanate nanosheets have a thickness of a few nano meters. According to X-ray diffraction (XRD) analysis, the exfoliated lanthanium titanate was found to be transformed into $Bi_{4-x}La_xTi_3O_{12}$ (x~2) after restacking with BiOCl and subsequent thermal treatment at > $700^{\circ}C$.

• Journal of Sensor Science and Technology
• /
• v.27 no.1
• /
• pp.1-5
• /
• 2018

Two-dimensional (2D) niobate-based nanosheets have attracted attention as high-k dielectric materials. We synthesized strontiumsubstituted calcium niobate ($Ca_{0.8}Sr_{1.2}Nb_3O_{10}$) nanosheets by a two-step cation exchange process from $KCa_{0.8}Sr_{1.2}Nb_3O_{10}$ ceramic. The $K^+$ ions were exchanged with $H^+$ ions, and then H+ ions were exchanged with tetrabutylammonium ($TBA^+$) cations. The $Ca_{0.8}Sr_{1.2}Nb_3O_{10}$ nanosheets were then exfoliated, decreasing the electrostatic interaction between each niobate layer. Furthermore, $Ca_2Nb_3O_{10}$ nanosheets were synthesized in same process for comparison. Each exfoliated nanosheet shows a single-crystal phase and has a lateral size of over 100 nm. The nanosheets were deposited on a $Pt/Ti/SiO_2/Si$ substrate by the electrophoretic deposition (EPD) method at 40 V, followed by ultraviolet irradiation of the films in order to remove the remaining $TBA^+$ ions. The $Ca_{0.8}Sr_{1.2}Nb_3O_{10}$ thin film exhibited twice the dielectric permittivity (~60) and lower dielectric loss than $Ca_2Nb_3O_{10}$ thin films.

• Particle and aerosol research
• /
• v.9 no.2
• /
• pp.51-57
• /
• 2013

A graphene(GR)-$TiO_2$ composite was synthesized from colloidal mixture of graphene oxide(GO) nanosheets and $TiO_2$ nanoparticles by an aerosol assisted self-assembly. The morphology, specific surface area and pore size of asprepared GR-$TiO_2$ composite were characterized by FE-SEM, BET, and BJH respectively. The shape of GR-$TiO_2$ composite was spherical. The average particle size was 0.5-1 ${\mu}m$ in diameter and the pore diameter ranged 20-50 nm. Photovoltaic characteristics of a mixture of the GR-$TiO_2$ and $TiO_2$ nanoparticles were measured by a solar simulator under simulated solar light. The highest photoelectric conversion efficiency of the mixture photoanode was 5.1%, which was higher than that of $TiO_2$ photoanode.

• Applied Chemistry for Engineering
• /
• v.31 no.6
• /
• pp.607-611
• /
• 2020

In this research, we synthesized Au/TiO2/graphene composites using ionic surfactants for the exfoliation of graphite layers, directly. In the graphene composite, TiO2 with thin nanosheet shapes was distributed on the graphene surface and Au nanoparticles with less than 10 nm sizes were evenly distributed on the surface of the TiO2 nanosheets. The Au/TiO2/graphene composite was then applied to the photodegradation of various dyes such as methylene blue, methylene orange and rhodamine 6G, and B. Among them, the methylene blue showed the most excellent photodegradation activity (91.6%) while the rhodamine B exhibited 31.0%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.1
• /
• pp.1-5
• /
• 2019

The physical properties of ceramic materials including oxides are greatly influenced by the material density. Therefore, various efforts have been made to increase the material density. One of the most popular strategies is to use sintering additives in sintering materials. The conventional sintering additive was a spherical powder having a three-dimensional structure. In this study, sintering additive with 2-dimensional (2D) layer structure was used to increase the sintering density of cerium oxide and its effect was confirmed. In this study, 1 nm-thick $TiO_x$ and $MnO_x$ nanosheets were used as sintering additives.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.6
• /
• pp.365-371
• /
• 2018

1D core-shell nanostructures have attracted great attention due to their enhanced physical and chemical properties. Specifically, oriented single-crystalline $TiO_2$ nanorods or nanowires on a transparent conductive substrate would be more desirable as the building core backbone. However, a facile approach to produce such structure-based hybrids is highly demanded. In this study, a three-step hydrothermal method was developed to grow NiMn-layered double hydroxide-decorated $TiO_2$/carbon core-shell nanorod arrays on transparent conductive fluorine-doped tin oxide (FTO) substrates. XRD, SEM, TEM, XPS and Raman were used to analyze the obtained samples. The in-situ fabricated hybrid nanostructured materials are expected to be applicable for photoelectrode working in water splitting.