• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.147-151
• /
• 2007

Cu-free multi-component sol, of which final oxide composition becomes $Bi_{1.9}Pb{0.35}SrCaO,\;Bi_{1.8}Pb_{0.2}SrCaO\;and\;Bi_{1.5}SrCaO$, respectively, was prepared through sol-gel route and coated on a bare Cu substrate. Starting materials were metal-alkoxides as follows.; [$Bi(OC_{2}H_{5})_{3}\;Pb(O^{1}C_{3}H_{7})_{2},\;Sr(O^{i}C_{3}H_{7})_{2},\;Ca(OC_{2}H_{5})_{2}$] as a reagent grade. Transparent light yellowish sol was obtained in the case of $Bi_{1.9}Pb_{0.35}SrCaO\;and\;Bi_{1.8}Pb_{0.2}SrCaO$ composition and $Bi_{1.5}SrCaO$ composition's sol was light greenish. Each sol was repeatedly dip-coated on Cu substrate four times and pre-heated at $400^{\circ}C$ and finally heat-treated in the range of $740{\sim}900^{\circ}C$. In the results, crystalline phases confirmed by XRD were (2201) orthorhombic and monoclinic phases. However, only $Bi_{1.9}Pb_{0.35}SrCaO_{x}$ composition showed pseudo-superconductive behavior after heat-treatment at $900^{\circ}C$ for 12 seconds and then onset temperature was 77 K, even though it did not exhibit zero resistance below Tc.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.171.2-171.2
• /
• 2016

The 2-dimensiona electron gas (2DEG) layers have opened tremendous interests in the heterooxide interfaces formed between two insulating materials, especially between LaAlO3 and $SrTiO_3$. The 2DEG layers exhibit extremely high mobility and carrier concentrations along with metallic transport phenomena unlike the constituent oxide materials, i.e., $LaAlO_3$ and $SrTiO_3$. The current work inserted artificially the interfacial layer, $Sr_xCa_{1-x}TiO_3$ between $LaAlO_3$ and $SrTiO_3$, with the aim to controlling the 2-dimensional transports. The insertion of the additional materials affect significantly their corresponding electrical transports. Such features have been probed using DC and AC-based characterizations. In particular, impedance spectroscopy was employed as an AC-based characterization tool. Frequency-dependent impedance spectroscopy have been widely applied to a number of electroceramic materials, such as varistors, MLCCs, solid electrolytes, etc. Impedance spectroscopy provides powerful information on the materials system: i) the simultaneous measurement of conductivity and dielectric constants, ii) systematic identification of electrical origins among bulk-, grain boundary-, and electrode-based responses, and iii) the numerical estimation on the uniformity of the electrical origins. Impedance spectroscopy was applied to the $LaAlO_3/Sr_xCa_{1-x}TiO_3/SrTiO_3$ system, in order to understand the 2-dimensional transports in terms of the interfacial design concepts. The 2-dimensional conduction behavior system is analyzed with special emphasis on the underlying mechanisms. Such approach is discussed towards rational optimization of the 2-dimensional nanoelectronic devices.

• Korean Journal of Materials Research
• /
• v.7 no.6
• /
• pp.505-509
• /
• 1997

FRAM(Ferroelectric Random Access memory)에의 응용을 위해 rf magnetron sputtering법을 이용하여 SrB $i_{2}$T $a_{2}$ $O_{9}$(SBT)박막을 증착하였다. 사용된 기판은 Pt/Ti/Si $o_{2}$Si이었으며 50$0^{\circ}C$에서 증착한 후 80$0^{\circ}C$의 산소 분위기 하에서 1시간 동안 열처리하였다. 증착시 증착 압력을 변화시켜 가면서 이에 따른 특성의 변화를 고찰하였다. 박막내의 Bi와 Sr의 부족을 보상하기 위해 20mole%의 Bi $O_{2}$와 30mole%의 SrC $O_{3}$를 과잉으로 넣어 타겟을 제조후 사용하였고 박막들의 두께는 300nm의 두께를 가지며 증착압력에 따라 다른 미세 구조르 보였다. 10mtorr에서 증착한 박막의 조성은 S $r_{0.6}$B $i_{3.8}$Ta/ sub 2.0/ $O_{9.0}$이었다. 이 SBT 박막의 잔류 분극(2 $P_{r}$)과 보전계(2 $E_{c}$)값은 각각 인가 전압 5V에서 18.5 $\mu%C/$\textrm{cm}^2$과 150kV/cm이었고, signal/noise비는 3V에서 4.6을 나타내었다. 5V의 bipolar pulse하에서 $10^{10}$cycle까지 피로 현상이 나타나지 않았으며, 누설 전류 밀도는 133kV/cm에서 약 1x$10^{-7A}$$\textrm{cm}^2$의 값을 보였다.을 보였다.

• Nuclear Engineering and Technology
• /
• v.55 no.9
• /
• pp.3352-3358
• /
• 2023

Nuclear medicine seems to be a decent choice of medicine in the recent decade. The radioactive isotopes ⁵¹Cr, ⁸⁹Sr, ⁹⁹Tc, ¹³¹I, ¹³³Xe, ¹³⁷Cs and ¹⁵³Sm are extremely essential in nuclear medicine. The excitation functions of the ⁵⁴Fe (n, α) ⁵¹Cr, ⁹²Zr (n, α) ⁸⁹Sr, ¹⁰²Rh (n, α) ⁹⁹Tc, 134Cs (n, α) ¹³¹I, ¹³⁶Ba (n, α) ¹³³Xe, ¹⁴⁰La (n, α) ¹³⁷Cs and ¹⁵⁶Gd (n, α) ¹⁵³Sm reactions were calculated in this study using the EMPIRE 3.2.3 and TALYS 1.95 nuclear codes. Additionally, the cross sections at 14-15 MeV were calculated using empirical formulae and the experimental data. The computer codes were compared to the experimental data and Empirical formulas as well as the evaluated data (TENDL 2021, JENDL 3.3, JENDL 5, JEFF 3.3, EAF 2010, CENDL 3.1, CENDL 3.2, ROSFOND 2010, FENDL 3.2 b, and BROND 3.1).

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.635-641
• /
• 2002

Electrical conduction of $SrZrO_3$ doped with $Y_2O_3$ was measured as a function of gas atmosphere and temperature by impedance spectroscopy. Hydrogen dissolution, due to an enhanced driving force in the presence of oxygen, results in protonation by water incorporation. Proton conductivity increased with water vapor pressure, ${P_w}^{1/2}$. In the pure hydrogen atmosphere, the dissolution of hydrogen,$H_2(g)=2H_{i}$ +2e', is supposed to be driven by a reduced activity of electrons, ascribable to their trapping in oxygen vacancies. The activation energy of electrical conductivity was 50 kJ/mol, in wet argon atmosphere in the temperature range of $600~900^{\circ}C$, similar to those reported for proton conduction in the literature. Grain boundary effect in proton conduction was substantial in the 10% doped case at temperatures lower than $700^{\circ}C$.

• Economic and Environmental Geology
• /
• v.39 no.5 s.180
• /
• pp.555-566
• /
• 2006

Major, trace and rare earth elements data of the Cretaceous Jindong granitic rocks were investigated in order to constrain the magma source characteristics and to establish the paleotectonic environment of the southwestern part of the Gyeongsang Basin. Geochemical signatures of the granitic rocks from the study area indicate that all of the rocks have characteristics of calc-alkaline series in the subalkaline field, and progressively shift from metaluminous to peraluminous with differentiation. In the variation diagrams, the overall geochemical features of the granites show systematic variations in major and trace elements. Chondrite normalized REE patterns show generally enriched LREE((La/Yb)c=4.2-12.8) and slight negative to flat Eu anomalies. Rb-Sr isotope data of the Jindong granites show that the whole rock age and Sr initial ratio are $114.6{\pm}9.1Ma$ and 0.70457, respectively. The Sr initial ratio of the Jindong granites is very similar to those of the Creataceous granites from Masan, Kimhae and Busan area($^{87}Sr/^{86}Sr=0.7049-0.707$). These results suggest that the magma have the mantle signature and intruded into the area during the early Cretaceous age. The Jindong granites have higher $Al_{2}O_{3},\;Na_{2}O$, Sr and lower $K_{2}O$, Y concentrations compared with typical calc-alkaline granitic rocks. These adakitic signatures are similar to those of adakitic pluton on Kyushu Island, southwest Japan arc. On the ANK vs. ACNK and tectonic discrimination diagrams, parental magma type of the granites corresponds to I-type, VAG granite. Interpretations of the geochemical characteristics of the granitic rocks favor their emplacement at continental margin during the subduction of Izanagi plate.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.57-61
• /
• 1997

Formation of fluorite structure and other related crystal structures in the $Y_{0.8}Ta_{0.2}O_{1.7}$-MO(M=Ba, Sr, Ca and Mg) system has been studied $Ba_2YTaO_6,\;Sr_2YTaO_6$ of cubic perovskite type ordered structure anti $Y_2O_3$ of cubic structure were produced besides the defect fluorite structure when 4 moIob of BaO or SrO was added to $Y_{0.8}Ta_{0.2}O_{1.7}$ When CaO more than 8 nlol"/o was added to $Y_{0.8}Ta_{0.2}O_{1.7}$, monoclinic: $Ca_2YTaO$, and cubic $Y_2O_3$ were pri~tlucecl ;IS this sec:onci phases hesides the main fluorite truc,ture. Smglc phase of fluorite structure \vas 1)roduc:ciI when MgO was added up to 12 mol%, however, MgO appeared as the second phase besides the main fluorire structure when MgO was added more than lti moI0'. Consquently, it is considered rh;it the formation of tluorite structure is related with the formation of the cubic perovskite type ordered structure of $A_2(B'B")O_6$ as well as the cation radii of the additives.additives.

• Journal of the Korean Vacuum Society
• /
• v.3 no.2
• /
• pp.147-157
• /
• 1994

Valence or core electron excitations induced by Synchrotron radiation (SR) irradiation and ensuing chemical reactions can be applied for semiconductor processes i, e, deposition etching and modifications of thin film materials. Unique selectivity can be achieved by this photochemical reactions in deposition and etching. Some materials can be ecvaporated by SR irradiation which can be utilized for low temperature surface cleaning of thin films. Also SR irradiation significantly lowers the reaction temperature and photon activated surface reactions can be utilized for direct writing or projection lithography of electronic materials. This technique is especially effective in making nanoscale feature size with abrupt and well defined interfaces for next generation electronic devices.

• Journal of the Korean Magnetics Society
• /
• v.13 no.1
• /
• pp.29-35
• /
• 2003

Anisotropic Sr-ferrites were prepared by the spark plasma sintering process (SPS). The Ferrite particles were oriented and densified during sintering process, and the anisotropic ferrites were manufactured at low sintering temperature and a remarkable short time processing by SPS method. It was showed that the anisotropy of ferrite particles at the specimen outer side was more higher than that at the specimen center, and it seems possible that the orientation of ferrite particles was related to DC current. Magnetic and physical properties of sintered Sr-ferrites are Br = 3.15 kG, iHc : 2.67 kOe, and density : 5.033 g/cm$^3$ when the samples were sintered for 8 minutes at 106$0^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.2
• /
• pp.55-60
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in terms of different chemical compositions and various SrSO$_4$additions by centrifugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were 1050$^{\circ}C$, 1100$^{\circ}C$ and 550$^{\circ}C$ for 30 min, respectively. The mould rotating speed was 1000 rpm. A tube was annealed at 840$^{\circ}C$ for 72 hours in oxygen atmosphere. The plates like grains more than 20 $\mu\textrm{m}$ were well developed along the rotating direction of mould regardless of initial chemical compositions and the amounts of SrSO$_4$in Bi2212. The specimen with Bi2212 composition exhibited T$\_$c/ of 83 K, while the specimens fabricated with other compositions are lower than 60 K. The measured I$\_$c/ and J$\_$c/ at 77 K(B = 0 T) in Bi2212 with 7 % SrSO$_4$ composition were about 680 A and 380 A/$\textrm{cm}^2$.