• Transactions on Electrical and Electronic Materials
• /
• v.13 no.1
• /
• pp.27-30
• /
• 2012

This paper proposes a micro gas sensor for measuring $H_2S$ gas. This is based on a $SnO_2$-CuO multi-layer thin film. The sensor has a silicon diaphragm, micro heater, and sensing layers. The micro heater is embedded in the sensing layer in order to increase the temperature to an operating temperature. The $SnO_2$-CuO multi layer film is prepared by the alternating deposition method and thermal oxidation which uses an electron beam evaporator and a thermal furnace. To determine the effect of the number of layers, five sets of films are prepared, each with different number of layers. The sensitivities are measured by applying $H_2S$ gas. It has a concentration of 1 ppm at an operating temperature of $270^{\circ}C$. At the same total thickness, the sensitivity of the sensor with multi sensing layers was improved, compared to the sensor with one sensing layer. The sensitivity of the sensor with five layers to 1 ppm of $H_2S$ gas is approximately 68%. This is approximately 12% more than that of a sensor with one-layer.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.870-876
• /
• 1994

In order to investigate the growth behavior of $Y_{2}Ba_{1}Cu_{1}O_{5}$(211) particles in $Y_{1}Ba_{2}Cu_{3}O_{7-\delta}$(123), 123 samples were quenched in air after heat treatment on polycrystal and single crystal MgO substrates at $1100^{\circ}C$ for various periods. 211 grains grew with the increase in holding time. The growth of 211 grains was faster on the polycrystal MgO substrate than on the single crystal MgO substrate. In the samples with the compositions of 211+xCuO($0.2\le X \le 0.8$), the growth rate of 211 grains increased with the increase in CuO content. In the sample with x=0.6 the largest 211 grains were observed. 211 grains in the $Y_{2}Ba_{1}Cu_{1.8}Sn_{0.1}O_{5+\delta}$ samples were distributed very finely and homogeneously. The retarding effect of $SnO_2$ addition on the growth of 211 grain appeared more pronounced in a CuO melt than in a $BaCuO_{2}$+ CuO melt.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.262-263
• /
• 2007

Effect of co-doping on optical and electrical properties of $SnO_2$ based thin films were studied. $SnO_2$ ceramic targets with up to 50mol% $CuSb_2O_6$ were prepared by sintering mixed-oxide compact in the temperature range of $1100^{\circ}C{\sim}1300^{\circ}C$ in air. Thin films were then deposited onto glass substrates by pulsed laser deposition where substrate temperature was maintained in the range of $500{\sim}650^{\circ}C$ with oxygen pressure of 3m~7.5mTorr and energy density of $1Jcm^{-2}$. It was found that with the increase amount of dopant, the electrical properties of thin films tended to improve with the smallest resistivity value obtained at about 8mol% doping, further increase, however, usually impaired the optical transmission in the visible range.

• Korean Chemical Engineering Research
• /
• v.51 no.4
• /
• pp.518-522
• /
• 2013

Cyclohexanone is important intermediate for the manufacture of caprolactam which is monomer of nylron. Cyclohexanone is generally produced by dehydrogenation reaction of cyclohexanol. In this study, highly mesoporous metal oxides such as meso-$WO_3$, meso-$TiO_2$, meso-$Fe_2O_3$, meso-CuO, meso-$SnO_2$ and meso-NiO were synthesized using mesoporous silica KIT-6 as a hard template via nano-replication method for dehydrogenation of cyclohexanol. The overall conversion of cyclohexanol followed a general order: meso-$WO_3$ >> meso-$Fe_2O_3$ > meso-$SnO_2$ > meso-$TiO_2$ > meso-NiO > meso-CuO. In particular, meso-$WO_3$ significantly showed higher activity than the other mesoporous metal oxides. Therefore, the meso-$WO_3$ has wide range of application possibilities for dehydrogenation of cyclohexanol.

• Journal of the Korean Ceramic Society
• /
• v.41 no.1
• /
• pp.9-12
• /
• 2004

The effect of x wt% CuO-y wt% $V_2O_5$ content on the microwave properties of $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ (PCFNS) ceramics was investigated. In order to decrease the sintering temperature and use as a Low Temperature co-firing Ceramics (LTCC), CuO-$V_2O_5$ are added in the PCFNS. The bulk density, dielectric constant (${\varepsilon}_r$) and quality factor(Q${\cdot}f_0$) increased with increase in CuO content within a limited value. The microwave properties were degraded with increases in $V_2O_5$ content. The temperature coefficient of the resonant frequency (${\tau}_f$) of PCFNS was shifted to positive value abruptly with increasing the $V_2O_5$ content, while the ${\tau}_f$ was slightly shifted to positive value with increasing the CuO content. The optimized microwave properties, ${\varepsilon}_r$ = 88, Q${\cdot}f_0$ = 6100 (GHz), and ${\tau}_f$ = 18 ppm/$^{\circ}C$, were obtained in $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ with 0.2wt% CuO 0.05 wt% $V_2O_5$ and sintered at $1000^{\circ}C$ for 3 h. The relationship between the microstructure and microwave dielectric properties of ceramics was studied by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM)

• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.37-40
• /
• 2004

We investigated the effects of impurity doping on the electrical transport and magnetic properties of TEX>$(Ru, Sn)(Sr, La)<_2$$EuCeCu_2$$O_{z}$ samples. We found that Sn substitution fur Ru causes a significant decrease of the volume fraction of ferromagnetic phase, as well as a decrease of the temperature where the ferromagnetic component is observed. La substitution for Sr leads to an increase of the magnetic ordering temperature with a moderate change of ferromagnetic component. The experimental results are discussed in conjunction with the structural data, transport properties and a possible change of oxygen content.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.112-112
• /
• 2016

인체접촉시 니켈도금의 알러지 반응을 억제하기 위한 대체 도금기술인 비 시안계 Cu-Sn 합금도금을 개발함에 있어서, 황산구리5수화물과 황산제일주석을 금속염으로 하여 황산 및 계면활성제, 유화제 등을 포함한 각종 유기첨가제를 포함하였고 특히 은백색조의 외관 색상과 안정적인 Cu-Sn 합금전착을 위해 2종의 착화제인 EDTP($C_{14}H_{32}N_2O_4$)와 TEA(Triethanolamine)를 첨가한 비 시안계 Cu-Sn 합금 도금액을 도출하였다. Cu-Sn 합금도금 피막 조성의 균일화를 도모하기 위해서는 합금 도금액중의 Cu와 Sn 금속이온 농도를 일정하게 유지하는 것이 필요하다. 그러나 합금 도금액중 2가 주석이온($Sn^{2+}$)은 수용액중에서 4가 주석이온($Sn^{4+}$)으로 산화됨으로써 도금액 색상이 백탁이 되고 Stannic Hydroxide($Sn(OH)_4$, $SnO_2{\cdot}2H_2O$)이 생성되어 대량의 침전물이 침강하는 문제점이 발생되는 등 시간 경과에 따른 도금액의 경시 변화가 발생되었다. 상기 침전물은 연속여과에 의해 제거 가능하나 합금 도금액중 $Sn^{2+}$ 농도가 지속적으로 감소하게 된다. 이는 합금 도금액중 금속이온 비율이 변동함으로써 합금도금 피막의 조성비를 일정하게 유지하는 것이 곤란해진다. 이에 $Sn^{4+}$ 침전물 생성을 방지하기 위한 산화방지제를 개발하고 또한 산화방지제의 첨가에 따른 도금 피막 외관에 미치는 영향을 평가하여 외관 개선을 위한 광택제를 개발하고자 한다. 본 연구의 결과를 토대로 니켈도금과 동등 이상의 기능 특성을 갖는 비시안계 Cu-Sn 합금도금액을 개발하여 실용화하는 것을 목적으로 하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.68.2-68.2
• /
• 2017

인체접촉시 니켈도금의 알러지 반응을 억제하기 위한 대체 도금기술인 비 시안계 Cu-Sn 합금도금을 개발함에 있어서, 황산구리5수화물과 황산제일주석을 금속염으로 하여 황산 및 계면활성제, 유화제 등을 포함한 각종 유기첨가제를 포함하였고 특히 은백색조의 외관 색상과 안정적인 Cu-Sn 합금전착을 위해 2종의 착화제인 EDTP (Ethylenediaminetetrapropanol, $C_{14}H_{32}N_2O_4$)와 TEA (Triethanolamine)를 첨가한 비 시안계 Cu-Sn 합금 도금액을 도출하였다. Cu-Sn 합금도금 피막 조성의 균일화를 도모하기 위해서는 합금 도금액중의 Cu와 Sn 금속이온 농도를 일정하게 유지하는 것이 필요하다. 그러나 합금 도금액 중 2가 주석이온($Sn^{2+}$)은 수용액 중에서 4가 주석이온($Sn^{4+}$)으로 산화됨으로써 도금액 색상이 백탁이 되고 Stannic Hydroxide($Sn(OH)_4$, $SnO_2{\cdot}2H_2O$)이 생성되어 대량의 침전물이 침강하는 문제점이 발생되는 등시간 경과에 따른 도금액의 경시 변화가 발생되었다. 상기 침전물은 연속여과에 의해 제거 가능하나 합금 도금액 중 $Sn^{2+}$ 농도가 지속적으로 감소하게 된다. 이는 합금 도금액 중 금속이온 비율이 변동함으로써 합금도금 피막의 조성비를 일정하게 유지하는 것이 곤란해진다. 이에 $Sn^{4+}$ 침전물 생성을 방지하기 위한 산화방지제를 개발하고 또한 산화방지제의 첨가에 따른 도금 피막 외관에 미치는 영향을 평가하여 외관 개선을 위한 광택제를 개발하고자 한다. 본 연구의 결과를 토대로 니켈도금과 동등 이상의 기능 특성을 갖는 비 시안계 Cu-Sn 합금도금액을 개발하여 실용화하는 것을 목적으로 하였다.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.121-126
• /
• 2003

The electromagnetic properties and microstructures of the basic composition of (N $i_{0.2}$C $u_{0.2}$Z $n_{0.6}$)$_{1.085}$(F $e_2$ $O_3$)$_{0.915}$ were invested by changing of the additive Sn $O_2$, CaO amounts and ferrite processes. There is no variation of grain size by changing additive amount. It can reduce the total loss when (N $i_{0.2}$C $u_{0.2}$Z $n_{0.6}$)$_{1.085}$(F $e_2$ $O_3$)$_{0.915}$ composition sintered at 1150 $^{\circ}C$ better than 130$0^{\circ}C$. Additive CaO confirmed of useful addition for the reduce total loss, because it increasing sintering density. Decreasing total loss were observed by adding both Sn $O_2$ 0.06 wt％ and CaO 0.4 wt％.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.169-171
• /
• 2006

Solderability and reaction properties were investigated for four Pb-free alloys as a function of Ag contents; Sn-4.0Ag-0.5Cu, Sn-3.0Ag-0.5Cu, Sn-2.5Ag-0.5Cu, and Sn-1.0Ag-0.5Cu. The alloy of the lowest Ag content, i.e., Sn-1.0Ag-0.5Cu, showed poor wetting properties as the reaction temperature decreased to 230oC. Variation of Ag concentration in the Sn-xAg-0.5Cu alloy shifted exothermic peaks indicating the undercooling temperature in DSC curve. For the aging process at 170oC, the thickness of IMCs at the board-side solder/Cu interface increased with the Ag concentration.