• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.185.2-185.2
• /
• 2015

Tin Oxide (SnO2) has been widely investigated as a transparent conducting oxide (TCO) and can be used in optoelectronic devices such as solar cell and flat-panel displays. In addition, it would be applicable to fabricating the wide bandgap semiconductor because of its bandgap of 3.6 eV. There have been concentrated on the improvement of optical properties, such as conductivity and transparency, by doping Indium Oxide and Gallium Oxide. Recently, with development of fabrication techniques, high-qulaity SnO2 epitaxial thin films have been studied and received much attention to produce the electronic devices such as sensor and light-emitting diode. In this study, powder sputtering method was employed to deposit epitaxial thin films on sapphire (0001) substrates. A commercial SnO2 powder was sputtered. The samples were prepared with varying the growth parameters such as gas environment and film thickness. Then, the samples were characterized by using XRD, SEM, AFM, and Raman spectroscopy measurements. The details of physical properties of epitaxial SnO2 thin films will be presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1600-1604
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis of used slurry.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.93-96
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis of used slurry.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.389-392
• /
• 2004

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) layer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2$-CMP process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and non-uniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between particle size and CMP with particle size analysis of used slurry.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.184-187
• /
• 2003

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric(IMD) lyaer with free-defect. The effect of alternative commerical slurries pads, and post-CMP cleaning alternatives are discuess, with removal rate, scratch dentisty, surface roughness, dishing, erosion and particulate density used as performance metrics. we investigated the performance of $SnO_2-CMP$ process using commonly used silica slurry, ceria slurry, tungsten slurry. This study shows removal rate and nonuniformity of $SnO_2$ thin film used to gas sensor by using Ceria, Silica, W-Slurry after CMP process. This study also shows the relation between partical size and CMP with partical size analysis or used slurry.

• 한국세라믹학회지
• /
• 제39권9호
• /
• pp.840-845
• /
• 2002

오존 가스센서는 저가이고 휴대 및 사용이 간편하며 감도가 높고 우수한 선택성을 지닌 반도체식 가스센서가 대안으로 부각되고 있다. 본 연구에서는 R.F. magnetron sputtering법을 이용하여 ITO($In_2O_3 95%,\;SnO_2$ 5%) 박막을 알루미나 기판위에 증착시켰다. 증착시 기판온도는 300$^{\circ}C$와 500$^{\circ}C$였고, 시편의 일부를 공기중 500$^{\circ}C$에서 4시간 동안 열처리하였다. ITO 가스 감지막은 열처리 전${\cdot}$후 모두 결정을 형성하였다. 오존 가스에 대한 감도측정 결과, 300$^{\circ}C$에서 증착한 다음 열처리한 센서에서 가장 높은 감도(1 ppm이하 감지 가능)를 나타내었다. 작동온도가 높을수록 감도는 줄어들었지만 빠른 응답 특성과 안정성을 가졌다.

• 센서학회지
• /
• 제13권5호
• /
• pp.323-328
• /
• 2004

N-type semi-conducting oxides such as $SnO_{2}$, ZnO, and $ZrO_{2}$ have been known for the detecting materials of inflammable or toxic gases. Of those materials, $SnO_{2}$-based sensors are well known as high sensitive materials to detect toxic gases. And the sensitivity is improved if catalysts are added. Detecting toxic gases, especially DMMP (di-methyl-methyl-phosphonate) and DPGME (Dipropylene glycol methyl ether), was performed by a mixture of Tin oxide ($SnO_{2}$) and Zirconia ($ZrO_{2}$). The films consist of each three different mass% of Zr (from 1 mass% to 5 mass%), and they were tested by XRD, SEM, TEM, BET. Nano-structure, pore and particle size was controlled to verify the sensor's sensing mechanism. The sensors was evaluated at five different degrees (from $200^{\circ}C$ to $400^{\circ}C$) and three different concentrations (from 500 ppb to 1500 ppb). The sensors had good sensitivity of both simulants, and high selectivity of DMMP.

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.411-420
• /
• 2017

In this paper, two methods of making the Pd-added $SnO_2$ ($Pd-SnO_2$) powder with pure tetragonal phase by the hydrazine method were suggested and compared in terms of crystal structure, surface morphology, and alcohol gas response. One of the addition methods is to use $PdCl_2$ as a Pd source, the other is to use Pd-based organic with oleylamine (OAM). When Pd concentration was increased from 0 to 5 wt%, the average grain size of $Pd-SnO_2$ made with Pd-OAM were decreased from 32 to 12 nm. In the case of using with $PdCl_2$, grain size of the $PdCl_2$ fell to less than 10 nm. However, agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The crack-free $Pd-SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of patterned Pt electrodes by optimized ink dropping method. Also, the 2 wt% $Pd-SnO_2$ thick film made with PdCl2 showed gas responses ($R_{air}/R_{gas}$) of 3.7, 5.7 and 9.0 at alcohol concentrations of 10, 50 and 100 ppm, respectively. On the other hand, the prepared 3 wt% $Pd-SnO_2$ thick film with Pd-OAM exhibited very excellent responses of 3.4, 6.8 and 12.2 at the equivalent measurement conditions, respectively. The 3 wt% $Pd-SnO_2$ thick film with Pd-OAM has a specific surface area of $31.39m^2/g$.

• The Korean Journal of Ceramics
• /
• 제4권3호
• /
• pp.183-188
• /
• 1998

Gas sensitizations of tin oxide film were investigated by measuring the change of film resistance in various gas atmospheres such as $N_2,\; O_2,\; H_2O$. The main test sample, polycrystalline $SnO_2$ film containing small Sb as a dopant was prepared by a sputtering technique and showed a long term stability in base resistance and thus, in gas sensitivity. The adsorption of oxygen on the film surface as a type of $(O_{ads})$ at the temperature of around $300^{\circ}C$ played important roles in sensor operating mechanism. The roles were ⅰ) the increase of base resistance in ambient air, which consequently lead to high sensitivity and ⅱ) the promotion of fast recovery. The reaction of hydrogen gas with the already adsorbed $(O_{ads})$ ions was considered as a decisive sensitization mechanism of tin oxide film. However, the dissociation of hydrogen molecules on film surface, by direct donation of electron to film also took a major part in the sensitization. The effect of humidity on gas sensitization was found to be negligible at the sensor operating temperature of around $300^{\circ}C$.

• 센서학회지
• /
• 제33권1호
• /
• pp.40-47
• /
• 2024

The creation of vertically aligned one-dimensional (1D) nanostructures through the decoration of n-type tin oxide (SnO₂) on p-type chromium oxide (Cr₂O₃) constitutes an effective strategy for enhancing gas sensing performance. These heterostructures are deposited in multiple stages using a glancing angle deposition technique with an electron beam evaporator, resulting in a reduction in the surface porosity of the nanorods as SnO₂ is incorporated. In comparison to Cr₂O₃ films, the bare Cr₂O₃ nanorods exhibits a response 3.3 times greater to 50 ppm H₂S at 300℃, while the SnO₂-decorated Cr₂O₃ nanorods demonstrate an eleven-fold increase in response. Furthermore, when subjected to various gases (CH₄, H₂S, CO₂, H₂), a notable selectivity toward H₂S is observed. This study paves the way for the development of p-type semiconductor sensors with heightened selectivity and sensitivity towards H₂S, thus advancing the prospects of gas sensor technology.