• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.209-212
• /
• 2001

Polyimide(PI) films have been considered as the interlayer dielectric materials due to low dielectric constant, low water absorption, high gap-fill and planarization capability. The PI film was etched with using inductively coupled plasma (ICP). The etching characteristics such as etch rate and selectivity were evaluated to gas mixing ratio. High etch rate was 8300$\AA$/min and vertical profile was approximately acquired 90$^{\circ}$ at CF$_4$/(CF$_4$+O$_2$) of 0.2. The selectivies of polyimide to PR and SiO$_2$ were 1.2, 5.9, respectively. The etching profiles of PI films with an aluminum pattern were measured by a scanning electron microscope (SEM). The chemical states on the PI film surface were investigated by x-ray photoelectron spectroscopy (XPS). Radical densities of oxygen and fluorine in different gas mixing ratio of 07CF4 were investigated by optical emission spectrometer (OES).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.263-274
• /
• 1996

Titanium dioxide ($TiO_{2}$) film has been widely used as anti-reflection coating for solar cells but not as masking oxide for metallisation and diffusion of impurities. In this paper we have investigated the properties of $TiO_{2}$ for possible incorporation into solar cell processing sequence. Thus the use of a spray deposition system to form the $TiO_{2}$ film and the characterisation of this film to ascertain its suitability to solar cell processing. The spray-on $TiO_{2}$ film was found to be resistant to all the chemicals used in conjunction with solar cell processing. The high temperature anealing (in oxygen ambient) of the spray-on $TiO_{2}$ film resulted in an increased refractive index, which indicated the growth of an underlying thin film of $SiO_{2}$ film for the passivation of silicon surface which would reduce the recombination activities of the fabricated device. Most importantly, the successful incorporation of the $TiO{2}$ film will lead to the reduction of the many high temperature processing steps of solar cell to only one.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.174-174
• /
• 2008

Non-volatile memories using ferroelectric-gate field-effect transistors (Fe-FETs) with a metal/ferroelectric/semiconductor gate stack (MFS-FETs) make non-destructive read operation possible. In addition, they also have features such as high switching speed, non-volatility, radiation tolerance, and high density. However, the interface reaction between ferroelectric materials and Si substrates, i.e. generation of mobile ions and short retention, make it difficult to obtain a good ferroelectric/Si interface in an MFS-FET's gate. To overcome these difficulties, Fe-FETs with a metal/ferroelectric/insulator/semiconductor gate stack (MFIS-FETs) have been proposed, where insulator as a buffer layer is inserted between ferroelectric materials and Si substrates. We prepared $SrBi_2Ta_2O_9$ (SBT) film as a ferroelectric layer and $LaZrO_x$ (LZO) film as a buffer layer on p-type (100) silicon wafer for making the MFIS-FET devices. For definition of source and drain region, phosphosilicate glass (PSG) thin film was used as a doping source of phosphorus (P). Ultimately, the n-channel ferroelectric-gate FET using the SBT/LZO/Si Structure is fabricated. To examine the ferroelectric effect of the fabricated Fe-FETs, drain current ($I_d$) versus gate voltage ($V_g$) characteristics in logarithmic scale was measured. Also, drain current ($I_d$) versus drain voltage ($V_d$) characteristics of the fabricated SBT/LZO/Si MFIS-FETs was measured according to the gate voltage variation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.255-255
• /
• 2010

Recently, nonvolatile memories (NVM) of various types have been researched to improve the electrical performance such as program/erase voltages, speed and retention times. Also, the charge trap memory is a strong candidate to realize the ultra dense 20-nm scale NVM. Furthermore, the high charge efficiency and the thermal stability of SiC nanocrystals NVM with single $SiO_2$ tunnel barrier have been reported. [1-2] In this study, the SiC charge trap NVM was fabricated and electrical properties were characterized. The 100-nm thick Poly-Si layer was deposited to confined source/drain region by using low-pressure chemical vapor deposition (LP-CVD). After etching and lithography process for fabricate the gate region, the $Si_3N_4/SiO_2/Si_3N_4$ (NON) and $SiO_2/Si_3N_4/SiO_2$ (ONO) barrier engineered tunnel layer were deposited by using LP-CVD. The equivalent oxide thickness of NON and ONO tunnel layer are 5.2 nm and 5.6 nm, respectively. By using ultra-high vacuum magnetron sputtering with base pressure 3x10-10 Torr, the 2-nm SiC and 20-nm $SiO_2$ were successively deposited on ONO and NON tunnel layers. Finally, after deposited 200-nm thick Al layer, the source, drain and gate areas were defined by using reactive-ion etching and photolithography. The lengths of squire gate are $2\;{\mu}m$, $5\;{\mu}m$ and $10\;{\mu}m$. The electrical properties of devices were measured by using a HP 4156A precision semiconductor parameter analyzer, E4980A LCR capacitor meter and an Agilent 81104A pulse pattern generator system. The electrical characteristics such as the memory effect, program/erase speeds, operation voltages, and retention time of SiC charge trap memory device with barrier engineered tunnel layer will be discussed.

• Journal of Information Display
• /
• v.10 no.3
• /
• pp.125-130
• /
• 2009

The new organic semiconductor, which is composed of a divinylbenzene core unit and alkoxynaphthalene on both sides, 1,4-bis-2-(6-hexyloxy)naphthalen-2-yl-vinylbenzene, was synthesized via Wittig reaction. The obtained oligomer was characterized via FT-IR, mass and elemental analysis, UV-visible spectroscopy, cyclovoltammetry, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The vacuum-evaporated film was characterized via X-ray diffraction and atomicforce microscopy (AFM). It formed a highly ordered polycrystalline vacuum-evaporated film and exhibited a good field-effect performance, with a hole mobility of $0.015cm^2/V{\cdot}s$, an on/off ratio of $1.18{\times}10^5$, and a subthreshold slope of 0.69 V when it was deposited at Ts=$90^{\circ}C$ on HMDS-treated $SiO_2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.452-455
• /
• 2003

[ $ZrO_2$ ] dielectric layers were grown on the p-type Si (100) substrate by metalorganic molecular beam epitaxy(MOMBE). Zrconium t-butoxide, $Zr(O{\cdot}t-C_4H_9)_4$ was used as a Zr precursor and Argon gas was used as a carrier gas. The thickness of the layers was measured by scanning electron microscopy (SEM) and the properties of the $ZrO_2$ layers were evaluated by X-ray diffraction, high frequency capacitance-voltage measurement. and HF C-V measurements have shown that $ZrO_2$ layer grown by MOMBE has a high dielectric constant (k=18-19). The growth rate is affected by various process variables such as substrate temperature, bubbler temperature, Ar, and $O_2$ gas flows.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.468-470
• /
• 1999

One of the most critical problem in etching of platinum was generally known that the etch slope was gradual. therefore, the addition of $N_2$ gas into the Ar/C1$_2$ gas mixture, which has been proposed the optimized etching gas combination for etching of platinum in our previous article, was performed. The selectivity of platinum film to oxide film as an etch mask increased with the addition of N2 gas, and the steeper etch slope over 75 $^{\circ}$ could be obtained. These phenomena were interpreted the results the results of a blocking layer such as Si-N or Si-O-N on the oxide mask. Compostional analysis was carried out by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS). Moreover, it could be obtained the higher etch rate of Pt film and steeper profile without residues such as p.-Cl and Pt-Pt ant the addition N\ulcorner of 20 % gas in Ar(90)/Cl$_2$(10) Plasma. The Plasma characteristic was extracted from optical emissionspectroscopy (OES).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.393-397
• /
• 2002

Polyimide (PI) films have been studied widely as the interlayer dielectric materials due to a low dielectric constant, low water absorption, high gap-fill and planarization capability. The polyimide film was etched using inductively coupled plasma system. The etcying characteristics such as etch rate and selectivity were evaluated at different $CF_4/(CF_4+O_2)$chemistry. The maximum etch rate was 8300 ${\AA}/min$ and the selectivity of polyimide to SiO$_2$was 5.9 at $CF_4/(CF_4+O_2)$ of 0.2. Etch profile of polyimide film with an aluminum pattern was measured by a scanning electron microscopy. The vertical profile was approximately $90^{\circ}$ at $CF_4/(CF_4+O_2)$ of 0.2. As 20% $CF_4$ were added into $O_2$ plasma from the results of the optical emission spectroscopy, the radical densities of fluorine and oxygen increased with increasing $CF_4$ concentration in $CF_4/O_2$ from 0 to 20%, resulting in the increased etch rate. The surface reaction of etched PI films was investigated using x-ray photoelectron spectroscopy.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1710-1712
• /
• 1999

암모니아가스에 민감한 In이 도핑된 ZnO(ZnO:In) 박막을 In 박막$(100{\AA})$ 및 ZnO박막$(3000{\AA})$의 연속적인 증착과 열처리공정을 통하여 제조하고, 이와 같은 방법으로 Al과 In이 도핑된 ZnO (ZnO:Al, In) 박막을 In 박막과 ZnO:Al 박막의 연속적인 증착과 같은 조건에서의 열처리를 통하여 제조하였다. 기판은 $1000{\AA}$의 산화막이 열적으로 성장되어 있는 Si 기판을 사용하였다. In/ZnO 및 In/ZnO:Al 박막 이중층의 열처리온도에 따른 구조적 및 전기적 특성을 x-선회절기, 주사전자현미경, 오제전자분광법 및 4점측정시스템을 통하여 조사하였다. 이들 막에 대하여 열처리온도에 따른 암모니아가스에 대한 감도, 선택성 및 시간응답특성을 구하였다. 열처리온도 $400^{\circ}C$, 동작온도 $300^{\circ}C$에서 100 ppm의 암모니아가스를 주입한 결과 140 %의 최대감도를 나타내었으며 CO, $NO_x$ 가스에 대한 감도는 아주 낮은 것으로 나타났다.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.3
• /
• pp.116-119
• /
• 2010

The etching characteristics of zinc oxide (ZnO) were investigated, including the etch rate and the selectivity of ZnO in a $Cl_2/BCl_3$/Ar plasma. It was found that the ZnO etch rate, the RF power, and the gas pressure showed non-monotonic behaviors with an increasing Cl2 fraction in the $Cl_2/BCl_3$/Ar plasma, a gas mixture of $Cl_2$(3 sccm)/$BCl_3$(16 sccm)/Ar (4 sccm) resulted in a maximum ZnO etch rate of 53 nm/min and a maximum etch selectivity of 0.89 for ZnO/$SiO_2$. We used atomic force microscopy to determine the roughness of the surface. Based on these data, the ion-assisted chemical reaction was proposed as the main etch mechanism for the plasmas. Due to the relatively low volatility of the by-products formed during etching with $Cl_2/BCl_3$/Ar plasma, ion bombardment and physical sputtering were required to obtain the high ZnO etch rate. The chemical states of the etched surfaces were investigated using X-ray photoelectron spectroscopy (XPS). This data suggested that the ZnO etch mechanism was due to ion enhanced chemical etching.