• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1211-1217
• /
• 2000

The three-dimensional finite-difference time-domain (FDTD) method and the two-dimensional quasi-static formulation have been used to calculate the characteristic impedance and the microwave effective index of coplanar waveguide structures on Lithium Niobate ($LiNBO_3$) single crystal substrates with a yttria-stabilized zirconia (YSZ) or $SiO_2$ buffer layer. The results shown can be a good source to predict the modulator characteristics. The effects of the thin buffer layer and anisotropy of the $LiNBO_3$ crystal (x-cut and z-cut) are discussed. The comparison between the FDTD and quasi-static results shows good agreement. In this paper, the efficient modeling technique of the FDTD method for the coplanar waveguide (CPW) structures based on an anisotropic substrate with a thin buffer layer is developed.

• Architectural research
• /
• v.12 no.1
• /
• pp.49-55
• /
• 2010

Stone powder sludge is a by-product of the manufacturing process of crushed sand. Most of it is dumped with soil in landfills, and the disposal of stone powder sludge causes a major environmental problem. This paper investigates the applicability of stone powder sludge in fly ashbased geopolymer. For this, stone powder sludge was used to replace fly ash at a replacement ratio of 50% and 100% by weight. The compressive strength of the samples was measured and scanning electron microscopy/ energy dispersive spectroscopy (SEM/EDS) analysis and X-ray diffraction (XRD) were performed. The test results indicated that the optimum level of the alkali activator ratio ($Na_2SiO_3$/NaOH) for fly ash-based geopolymer using stone powder sludge was 1.5. The strength development is closely related to the NaOH solution concentration. In addition, the compressive strength of the sample cured at $25^{\circ}C$ was significantly improved between 7 days and 28 days, even though the strength of the sample showed the lowest value at 7 days. Microscopy results indicated that a higher proportion of unreacted fly ash spheres remained in the sample with 5M NaOH, and some pores on the surface of the sample were observed.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.4
• /
• pp.614-621
• /
• 2016

Micro-Doppler (MD) shift caused by the micro-motion of a ballistic missile (BM) can be very useful to identify it. In this paper, the MD signatures of three scale-model BMs are investigated using a portable measurement system. The measurement system consists of an X-band 2-by-2 phase comparison mono-pulse radar, and a mechanical device that can impart controlled spinning and coning motions simultaneously to a model to yield the MD signature that replicates the characteristic of each target and the corresponding micro-motion. The coning motion determined the overall period of MD, and the spinning motion increased its amplitude. MD was also dependent on aspect angle. The designed system is portable, and can implement many micro-motions; it will contribute to analysis of MD in various situations.

• Elastomers and Composites
• /
• v.31 no.5
• /
• pp.335-340
• /
• 1996

In order to look into the internal structure and the properties in the silicone rubbers added reinforcing fillers; silica $additives(O{\sim}140phr)$, and to examine the behavior of charged particles, the properties of thermally stimulated current(TSC) and X-Ray diffraction are investigated, respectively. And then, from the TSC which are formed by applying the electric field of $2{\sim}5kV/mm$ to specimen at the temperature range from -150 to $260^{\circ}C$, the results are as follwing: In the case of non-filled specimen, four peaks of ${\delta},\;{\gamma},\;{\beta}\;and\;{\alpha}$ are obtained at the temperature of $-120^{\circ}C,\;-60^{\circ}C,\;20^{\circ}C\;and\;130^{\circ}C$, respectively and the case of filled specimen, three peaks of ${\delta},\;{\alpha}_2\;and\;{\alpha}_1$ are observed at the temperature of $-120^{\circ}C,\;80^{\circ}C\;and\;130^{\circ}C$, respectively. The origins of these peaks are that, the ${\delta}$ peak seems to the result from the contribution of side chain methyl radical, and the ${\gamma}$ peak from the depolarization of space charge polarization owing to be added impurity during manufacturing specimens, and the ${\beta}$ peak from the orientation of $Si-CH_3$ dipole, and the ${\alpha}_2$ near the temperature of $80^{\circ}C$ from hydroxyl in carboxylic radical, and finally, the ${\alpha}_1$ peak near the temperature of $130^{\circ}C$ from carboxyl acid that is formed by the thermal oxidation of high temperature.

• Journal of Information Display
• /
• v.10 no.3
• /
• pp.125-130
• /
• 2009

The new organic semiconductor, which is composed of a divinylbenzene core unit and alkoxynaphthalene on both sides, 1,4-bis-2-(6-hexyloxy)naphthalen-2-yl-vinylbenzene, was synthesized via Wittig reaction. The obtained oligomer was characterized via FT-IR, mass and elemental analysis, UV-visible spectroscopy, cyclovoltammetry, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The vacuum-evaporated film was characterized via X-ray diffraction and atomicforce microscopy (AFM). It formed a highly ordered polycrystalline vacuum-evaporated film and exhibited a good field-effect performance, with a hole mobility of $0.015cm^2/V{\cdot}s$, an on/off ratio of $1.18{\times}10^5$, and a subthreshold slope of 0.69 V when it was deposited at Ts=$90^{\circ}C$ on HMDS-treated $SiO_2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.846-851
• /
• 2007

In this work, the etching characteristics of $Ge_2Sb_2Te_5(GST)$ thin films were investigated using an inductively coupled plasma (ICP) of $Cl_2/Ar$ gas mixture. To analyze the etching mechanism, an optical emission spectroscopy (OES) and surface analysis using X-ray photoelectron spectroscopy (XPS) were carried out. The etch rate of the GST films decreased with decreasing Ar fraction. At the same time, high selective etch rate over $SiO_2$ films was obtained and the selectivity over photoresist films decreased with increasing the he fraction. From XPS results, we found that Te halides were formed at the etching surface and Te halides limited the etch rate of the GST films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.263-267
• /
• 2007

We investigate the influence of the ambient gas during thermal annealing on the photoluminescence (PL) properties of europium-silicate thin films. The films were fabricated on substrates by using a radio-frequency magnetron sputtering method and subsequent rapid thermal annealing (RTA). The mechanism for the formation of the europium silicates during the annealing process was investigated by using X-ray diffraction (XRD) spectroscopy, Auger electron spectroscopy (AES) and transmission electron microscopy (TEM). A series of narrow PL spectra from $Eu^{3+}$ ions was observed from the film annealed in $O_2$ ambient. Broad PL spectra associated with $Eu^{2+}$ ions, with a maximum intensity at 600 nm and a FWHM of 110 nm, were observed from the thin film annealed at $1000^{\circ}C$ in $N_2$ ambient.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.119-122
• /
• 2011

A series of mesoporous silicalites was synthesized using different compositions of tetraethylorthosilicate and methyltriethoxysilane (MTES) as the silica source. Cetyltrimethylammonium bromide was used as the organic template. Their detailed pore structures were investigated by transmission electron microscopy, X-ray diffraction, and N2 adsorption method. The thermal properties of these silicalites were studied by thermogravimetric analysis. The increased amount of MTES destroyed mesoporous channels and reduced pore sizes from 3.4 nm to 2.8 nm in calcined silicalites. The calcined silicalite transformed completely into an amorphous state at 30% MTES loading. Methyl pending groups of MTES hindered the structural ordering of ≡Si-O- frameworks, resulting in an amorphous structure. This was caused by the insufficient formation of supramolecular assembly with the organic template. No capillary condensation step was found in MS 7/3 silicalite. The other capillary condensation steps shifted toward the lower relative pressure with increasing MTES content, indicating the reduction of pore sizes.

• Journal of Surface Science and Engineering
• /
• v.44 no.6
• /
• pp.246-249
• /
• 2011

Surface modification before coating nickel by coupling agents and/or etchant of glass did not provide enough adhesive strength of electroless nickel deposits on glass. Effect of heat treatments on hardness as well as adhesion of nickel deposits was studied by using tape test for adhesion, nanoindenter for hardness and glancing angle x-ray diffractometer (GAXRD) for phase characterization. Heat treatment improved hardness as well as adhesion. XRD results give that the improvements of adhesion and hardness are due to the formation of $NiSiO_4$ around the interface between the nickel deposits and the glass and the precipitation of $Ni_3P$ causing precipitation hardening, respectively. The details in effects of heat treatment on adhesion and hardness are described here.

• Korean Journal of Materials Research
• /
• v.25 no.11
• /
• pp.622-629
• /
• 2015

Cu circuits were successfully fabricated on flexible PET(polyethylene terephthalate) substrates using wettability difference and electroless plating without an etching process. The wettability of Cu plating solution on PET was controlled by oxygen plasma treatment and $SiO_x$-DLC(silicon oxide containing diamond like carbon) coating by HMDSO(hexamethyldisiloxane) plasma. With an increase of the height of the nanostructures on the PET surface with the oxygen plasma treatment time, the wettability difference between the hydrophilicity and hydrophobicity increased, which allowed the etchless formation of a Cu pattern with high peel strength by selective Cu plating. When the height of the nanostructure was more than 1400 nm (60 min oxygen plasma treatment), the reduction of the critical impalement pressure with the decreasing density of the nanostructure caused the precipitation of copper in the hydrophobic region.