• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.90-101
• /
• 2006

In this paper, the calibration parameters of the gyros and star hackers are estimated by using an on-orbit AOCS sensor calibration algorithm. The calibration algorithm was implemented by Kalman filter. In order to estimate gyro calibration parameters, the calibration algorithm requires calibration maneuver and it was analyzed whether the star trackers are protected by Sun, Moon and Earth or not. Also the star tracker calibration algorithm used the camera image information. This kinds of camera image information simulated ground control point and orbit information. The estimated accuracy of star tracker calibration parameters depends on camera image information.

• BioChip Journal
• /
• v.12 no.4
• /
• pp.340-347
• /
• 2018

$F{\ddot{o}}rster$ resonance energy transfer (FRET) is extremely sensitive to the separation distance between the donor and the acceptor which is ideal for probing such biological phenomena. Also, FRET-based probes have been developing for detecting an unamplified, low-abundance of target DNA. Here we describe the development of FRET based DNA sensor based on an accumulated QD system for detecting KRAS G12D mutation which is the most common mutation in cancer. The accumulated QD system consists of the polystyrene beads which surface is modified with carboxyl modified QDs. The QDs are sandwich-hybridized with DNA of a capture probe, a reporter probe with Texas-red, and a target DNA by EDC-NHS coupling. Because the carboxyl modified QDs are located closely to each other in the accumulated QDs, these neighboring QDs are enough to transfer the energy to the acceptor dyes. Therefore the FRET factor in the bead system is enhancing by the additional increase of 29.2% as compared to that in a single QD system. These results suggest that the accumulated nanobead probe with conjugated QDs can be used as ultrasensitive DNA nanosensors detecting the mutation in the various cancers.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.210-215
• /
• 2002

Optical Band-pass Filter(BPF) for the selected wavelength of 4300 nm was designed and fabricated on Si wager by alternately depositing Ge and $SiO_2$ thin layers by an electron beam evaporation technique. The fabricated BPF showed the optical transmittance characteristics of 58.2% with FWHM(Full Width at Half Maximum) of 204 nm at 4300 nm, but showed the transmittance less than 5% due to the reflectance over all the wavelength ranges except 4300 nm band. The $CO_2$ sensitivity of BPF was investigated with the transmittance as a function of $CO_2$ gas concentration using a sensing cell attached to FT-IR instrument. The transmittance of BPF was almost linearly decreased with increasing of $CO_2$ concentration in the range of from 500 to 5000 ppm. The sensing structure using double BPFs showed higher slop of transmittance vs $CO_2$ concentration, and thus higher gas sensitivity than that using a single BPF, even though the former had relatively lower transmittance.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.60-64
• /
• 2011

High sensitivity IR image sensors require materials characteristics with temperature coefficient of resistance (TCR) and IR range absorption. In this study, the metal-dielectric thermo sensitive films (MDTF) based on $(SiO_2)_x-(Ti)_y$ composition were deposited on substrates of germanium and glass by thermal evaporator. The $SiO_2$ : Ti mixture was made from the ratio of 9 : 1, 8 : 2, 7 : 3, 6 : 4, respectively. $(SiO_2)_x-(Ti)_y$ mixture powder was loaded on tungsten boat in evaporator and was 15.5 cm from the substrate. Resistance of $(SiO_2)_x-(Ti)_y$ in the range of 273~333K were measured as a function of temperature. Temperature coefficient of resistance (TCR) was calculated by the resistance variation. Under the various mixture ratios condition, it is possible to obtain $SiO_2$-Ti layers with resistance from units kilo-ohm to hundreds kilo-ohm. Finally, our results showed that Temperature coefficient of resistance (TCR) of these films varies from -1.4 to $-2.6%K^{-1}$.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.475-478
• /
• 2010

Fluorinated polymeric membranes were prepared by direct surface modification of PDMS with fluorine gas ($50{\sim}2000\;{\mu}mol/mol$ in nitrogen). The formed fluorinated polymeric membranes were characterized by FT-IR spectroscopy, GC (Gas chromatography), atomic force microscopy, and scanning electron microscopy. Direct fluorination resulted in the change of permeability and selectivity of various gases (pure gases such as $CO_2$, $O_2$, $N_2$, $C_2H_4$, mixture of He, Ne, Kr, Xe) through PDMS membranes. Fluorination resulted in the maximum 50% increase of selectivity through PDMS membrane.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.81-86
• /
• 1997

Platinum thin films were deposited on $SiO_{2}/Si$ and $Al_{2}O_{3}$ substrates by DC magnetron sputtering for RTD (resistance thermometer devices) temperature sensors. The resistivity and sheet resistivity of these films were decreased with increasing the annealing temperature and time. We made Pt resistance pattern on $Al_{2}O_{3}$ substrate by lift-off method and fabricated Pt-RTD temperature sensors by using W-wire, silver epoxy and SOG(spin-on-glass). In the temperature range of $25{\sim}400^{\circ}C$, we investigated TCR(temperature coefficient of resistance) and resistance ratio of Pt-RTD temperature sensors. TCR values were increased with increasing the annealing temperature, time and the thickness of Pt thin films. Resistance values were varied linearly within the range of measurement temperature. At annealing temperature of $1000^{\circ}C$, time of 240min and thin film thickness of $1{\mu}m$, we obtained TCR value of $3825ppm/^{\circ}C$ close to the Pt bulk value.

• Journal of Sensor Science and Technology
• /
• v.8 no.2
• /
• pp.189-194
• /
• 1999

The heat treatment effects of the undoped ZnO and Al doped ZnO(AZO) transparent conductive films prepared by rf magnetron sputtering were investigated. The variations of the electrical and optical properties with heat treatment temperature and ambient were studied. The resistivity of the un doped ZnO films heat treated in air and $H_z$ plasma for 1 hour increased rapidly above $200^{\circ}C$ and $300^{\circ}C$, respectively. And that of the ZnO:Al films heat treated in air also increased rapidly above $300^{\circ}C$. On the other hand that of the ZnO:Al films heat treated in $H_z$ plasma was constant regardless of heat treatment temperature. The optical transmittance above 550nm is about 90% for all thin films regardless of impurity doping, the heat treatment temperature and ambient.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.2
• /
• pp.87-91
• /
• 2011

Single layer Sn doped $In_2O_3$ (ITO) films and ITO 50 nm / Au 10 nm / ITO 40 nm (IAI) multilayer films were prepared with electron beam assisted magnetron sputtering on glass substrates. The effects of the Au interlayer, post-deposition atmosphere annealing and intense electron irradiation on the methanol gas sensitivity were investigated at room temperature. As deposited ITO films did not show any diffraction peaks in the XRD pattern, while the IAI films showed the diffraction peak for $In_2O_3$ (400). In this study, the gas sensitivity of ITO and IAI films increased proportionally with the methanol vapor concentration and an intense electron beam irradiated IAI film shows the higher sensitivity than the others film. From the XRD pattern, it is supposed that increased crystallization promotes the gas sensitivity. This approach is promising in gaining improvement in the performance of IAI gas sensors used for the detection of methanol vapor at room temperature.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.3.2-3.2
• /
• 2011

Nanofibers, one of various one-dimensional nanomaterials such as nanorods, nanowires and nanotubes have been successfully synthesized by many groups in recent years and their applications to chemical sensors, catalytic filters and biomedicine, etc. are extensively tested. In particular, there is a possibility that chemical sensors based on oxide nanofibers can overcome the shortcomings of chemical sensors based on single nanowires. In order to prepare oxide nanofibers, the electrospinning method is most widely used. In this work, we synthesized various oxide nanofibers including ZnO, SnO2 and CuO by employing an electrospinning method and various shapes of nanofibers including core-shell nanofibers and hollow nanofibers as well. The response properties of the various nanofibers to oxidizing and reducing gaseous species have been investigated systematically. The normal oxide nanofibers showed high sensitivity and quite fast response time to many gaseous species. Furthermore, derivatives of normal nanofibers including hollow nanofibers, core-shell nanofibers and heterostructured nanofibers display much superior sensing properties. These results hold promise for the practical application of oxide nanofibers to chemical sensors. In addition, the sensing mechanisms operated in the nanofibers will be discussed in detail.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1344-1351
• /
• 2004

This study develops a haptic display model which is an indispensable for the force generation in the virtual environment. In developing the haptic display model, a Proxy concept and a Karnopp friction model are utilized to generate the reaction force and the friction force. Also this study develops a 2 D.O.F. remote wiping system. This system is composed of a 2 D.O.F. master manipulator, a force sensor equipped 2 D.O.F. slave manipulator and a real time controller. With the developed remote wiping system, this study identifies the friction characteristic of the aluminum, acryl and rubber plate. The results are used as the dynamic friction coefficient of the haptic display model. This study shows the efficiency of the developed haptic display model by the comparison between the friction characteristic of the haptic display with the developed haptic display model and the friction characteristic of the real aluminum, acryl and rubber plate.