• Journal of the Korean Electrochemical Society
• /
• v.1 no.1
• /
• pp.40-44
• /
• 1998

The LAPS device of fast response and high sensitivity, based on electrochemical potential difference, and its system were fabricated for the precise measurement of pH changes and its characteristic were investigated. The electrostatic variation characteristics of LAPS according to the pH changes and parameters in the device were verified through a simulation using LAPS equivalent circuit model. The LAPS device and its system were fabricated on the basis of the result of simulation. The fabricated LAPS system showed linear sensitivity (about 56 mV/pH within the range of pH 2 to pH 11. In order to overcome the defect of general urea sensor (especially slow response time), urease immobilized nitrocellulose membrane was attached on the LAPS and resulted in the very fast response time, 0.29 mV/sec, 0.86 mV/sec at urea concentration of $50{\mu}g/ml,\; 500{\mu}g/ml$, respectively. And also in order to measure the uranyl ion, the uranyl ion selective sensing membrane with calix[6]arene derivative was used and its sensitivity was 25mV/concentration decade in the wide uranyl ion concentration range of $10^{-11}M\;to\;10^{-4}M$.

• Journal of Sensor Science and Technology
• /
• v.21 no.6
• /
• pp.395-401
• /
• 2012

The bond strength of three types of $TiO_2$ coatings onto fluorine-doped $SnO_2$ (FTO) glass was investigated with the aid of a tape test according to ASTM D 3359-95. Transmittance was then measured using an UV-vis spectrophotometer in the wavelength range of 300 nm to 800 nm to evaluate the extent of adhesion of $TiO_2$ nanorods/nanoparticles on FTO glass. A sharp interface between the coating layer and the substrate was observed for single $TiO_2$ coating ($TiO_2$ nanorods/FTO glass), which may be detrimental to the bonding strength. In multicoating sample ($TiO_2$ nanorod/$TiO_2$ nanoparticle/$TiO_2$ nanoparticle/FTO glass), the tape test was not performed due to severe peeling-off prior to the test. On the other hand, the dual coating sample ($TiO_2$ nanorod/$TiO_2$ nanoparticle/FTO glass) showed minimum variation of transmittance (4%) after the test, suggesting that the topcoat adheres well with the FTO substrate due to the presence of the $TiO_2$ nanoparticle buffer layer. The use of a $TiO_2$ nanorod electrode layer with good adhesion may be attributed to the excellent dye sensitized solar cell performance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.626-631
• /
• 2012

$SnO_2$ nanoparticles were synthesized by flame spray pyrolysis, which were directly deposited on Pt interdigitated substrates. Gas sensing performance was evaluated for various gases such as $H_2$, CO, $H_2S$, and $NH_3$, and it was compared with that of commercial $SnO_2$ nanopowder. The synthesis of $SnO_2$ nanoparticles was also conducted in various solvents. As a result, the primary particle size was changed with the solvent of precursor solution, and their $H_2$ sensing properties were significantly affected.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.1
• /
• pp.81-89
• /
• 1999

The fabrication process for miniaturizing the Electronic Article Surveillance (EAS) sensor was studied using micromachining technique. Two types of sensor structure, free standing membrane type and diving beard type, were proposed and researched for establishing the fabrication process. The membrane type structure was easy to change the sensor shape but had the limitation for miniaturizing, because the size of the sensor depends on the silicon substrate thickness. The diving board type structure has the advantage of miniaturization and of free motion. Since the elastic modulus is not trio high, SiN film is expected to be adequate for the supporting membrane of magnetic sensor. The selectivity of $H_2O_2$for sputtered W with respect to Fe-B-Si, which was studded for magnetic sensor materials, was high enough to be removed after using as a protection layer. Therefore, the diving board type process using the silicon nitride film for the supporter of the sensor material and the sputtered W for protection layer is expected to be useful fur miniaturizing the Electronic Article Surveillance (EAS) sensor.

• Journal of Sensor Science and Technology
• /
• v.7 no.5
• /
• pp.364-371
• /
• 1998

A novel antifuse has been developed for field programmable gate arrays (FPGA's) as a voltage programmable link with Al/$BaTiO_3/SiO_2$/TiW-silicide. The proper program voltage can be obtained by adjusting the deposition thickness of $BaTiO_3$ film. When a negative voltage was applied at bottom TiW-silicide electrode of the antifuse, based on $BaTiO_3(120{\AA})$/$SiO_2(120{\AA})$, the program voltage was about l4.4V and on-resistances were ranged between 40 and $50{\Omega}$. The current-voltage characteristics of antifuses are consistent with a Frenkel-Poole conduction model. However, there are some deviations depending on bias polarity that are probably due to the difference in the interface properties between Al/$BaTiO_3$ and TiW-silicide/$SiO_2$.

• Journal of the Korean Ceramic Society
• /
• v.40 no.11
• /
• pp.1073-1077
• /
• 2003

The Sn $O_2$-based gas sensors can detect inflammable and toxic gases of low concentration by the modulation of surface resistance, but they lack in selectivity on the whole. To give selectivity to the Sn $O_2$-based gas sensors, studies on the sensing mechanism, selective gas sensing materials and signal processing techniques are demanded. Ethanol (C$_2$ $H_{5}$OH) and acetonitrile ($CH_3$CN) were confirmed to undergo catalytic oxidation on Sn $O_2$ by gas chromatography. PdCl$_2$-doped Sn $O_2$ showed excellent sensitivity to ethanol and acetonitrile, while La$_2$ $O_3$-doped Sn $O_2$ showed excellent sensitivity to ethanol, but poor sensitivity to acetonitrile. Using these two sensors and pattern recognition, the selectivity to acetonitrile is greatly enhanced. The minimum detection level of acetonitrile was 15 ppm in air and 20 to 100 ppm when exposed to interfering gases together with acetonitrile.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.12 no.2
• /
• pp.89-96
• /
• 2017

We develop an embedded system to measure various sensor data, control multiple motors, and communicate with mobile devices for system managements. Choosing TI AM3359 microprocessor featuring high processing performance, low power consumption, and various I/O device support, we design and build the embedded system hardware so that it supports multiple global positioning system (GPS) and gyro sensor modules to measure precise position; multiple pulse width modulation (PWM) outputs to control multiple direct current (DC) motors; a Bluetooth module to communicate with mobile devices. Then, we port the boot loader and device drivers to the built circuit board and construct the firmware development environment for the application programming. The performance of the designed and implemented embedded system is demonstrated by real motor control test using GPS and gyro sensor data and control parameters configured by a mobile device.

• Journal of Powder Materials
• /
• v.24 no.5
• /
• pp.351-356
• /
• 2017

Tin dioxide nanoparticles are prepared using a newly developed synthesis method of plasma-assisted electrolysis. A high voltage is applied to the tin metal plate to apply a high pressure and temperature to the synthesized oxide layer on the metal surface, producing nanoparticles in a low concentration of sulfuric acid. The particle size, morphology, and size distribution is controlled by the concentration of electrolytes and frequency of the power supply. The as-prepared powder of tin dioxide nanoparticles is used to fabricate a gas sensor to investigate the potential application. The particle-based gas sensor exhibits a short response and recovery time. There is sensitivity to the reduction gas for the gas flowing at rates of 50, 250, and 500 ppm of $H_2S$ gas.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.69-71
• /
• 1993

Fluoride compound potentiometric cell oxygen sensors were fabricated for the measurement of oxygen pressure in the low temperature range (300。K-500。K). The disk type sensors consist of a reference Air(0$_2$):Ag, a solid electrolyte SrF$_2$, and a sensing metel Ag electrode. And the buried reference electrode type sensor have a NiO/Ni reference electrode. The open circuit emf of the cell showed high sensivity to oxygen gas (60mv) at the measuring temperature 20$0^{\circ}C$. Also, The buried reference electrode type sensor showed 30mv from 1% to 10% oxygen pressure range.

• Transactions of Materials Processing
• /
• v.31 no.2
• /
• pp.103-108
• /
• 2022

Systematic quality control based on real time data is required for modern factories. This study introduced a method of predicting punch wear in the trimming process of automobile parts. Based on monitoring data of the mass production process using a bolt-type piezo sensor, it was shown that precursor symptoms of die wear could be predicted from the change in load pattern with respect to production volume. The load pattern that changed according to the wear of the die was verified by numerical analysis.