• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.298-303
• /
• 2003

Bi$_4$-$_{x}$EU$_{x}$Ti$_3$O$_{12}$ (BET) thin films were etched by inductively coupled CF$_4$/Ar plasma. We obtained the maximum etch rate of 78 nm/min at the gas mixing ratio of CF$_4$(10%)/Ar(90%). The variation of volume density for F and Ar atoms are measured by the optical emission spectroscopy. As CF$_4$increased in CF$_4$/Ar plasma, the emission intensities of F increase, but Ar atoms decrease, which confirms our suggestion that emission intensity is proportional to the volume density of atoms. From X-ray photoelectron spectroscopy, the intensities of the Bi-O, the Eu-O and the Ti-O peaks are changed. By pure Ar plasma, intensity peak of the oxygen-metal (O-M : TiO$_2$, Bi$_2$O$_3$, Eu$_2$O$_3$) bond was seemed to disappear while the intensity of pure oxygen peak showed an opposite tendency. After the BET thin films was etched by CF$_4$/Ar plasma, the peak intensity of O-M bond increase slowly, but more quickly than that of peak belonged to pure oxygen atoms due to the decrease of Ar ion bombardment. Scanning electron microscopy was used to investigate etching Profile. The Profile of etched BET thin film was over 85$^{\circ}$./TEX>.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.72-74
• /
• 2004

In this study, we used a inductively coupled plasma (ICP) source for etching $Al_2O_3$ thin films because of its high plasma density, low process pressure and easy control bias power. $Al_2O_3$ thin films were etched using $Cl_2/BCl_3$, $N_2/Cl_2/BCl_3$, and Ar/$Cl_2/BCl_3$ plasma. The experiments were carried out measuring the etch rates and the selectivities of $Al_2O_3$ to $SiO_2$ as a function of gas mixing ratio, rf power, and chamber pressure. When $Cl_2$ 50% was added to $Cl_2/BCl_3$ plasma, the etch rate of the $Al_2O_3$ films was 118 nm/min. We also investigated the effect of gas addition. In case of $N_2$ addition, the etch rate of the $Al_2O_3$ films decreased while $N_2$ was added into $Cl_2/BCl_3$ plasma. However, the etch rate increased slightly as Ar added into $Cl_2/BCl_3$ plasma, and then further increase of Ar decreased the etch rate. The maximum etch rate was 130 nm/min at Ar 20% in $Cl_2/BCl_3$ plasma, and the highest etch selectivity was 0.81 in $N_2$ 20% in $Cl_2/BCl_3$ plasma. And, we obtained the results that the etch rate increases as rf power increases and chamber pressure decreases. The characteristics of the plasmas were estimated using optical emission spectroscopy (OES).

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.5
• /
• pp.202-205
• /
• 2010

In this study, the etch properties of $Al_2O_3$ thin films deposited by atomic layer deposition were investigated as a function of the $O_2$ content in $BCl_3$/Ar inductively coupled plasma. The experiments were performed by comparing the etch rates and selectivity of $Al_2O_3$ over the hard mask materials as functions of the input plasma parameters, such as the gas mixing ratio, DC-bias voltage, ratio-frequency (RF) power and process pressure. The highest obtained etch rate was 477 nm/min at an RF power of 700 W, $O_2$ to $BCl_3$/Ar gas ratio of 15%, DC-bias voltage of -100 V and process pressure of 15 mTorr. The deposition occurred on the surfaces when the amount of $O_2$ added to the $BCl_3$/Ar gas was too high at a low DC-bias voltage or high process pressure. X-ray photoelectron spectroscopy was used to investigate the chemical reactions on the etched surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.62-65
• /
• 2001

$SrBi_2Ta_2O_{9}$ thin films were etched in inductively coupled $Cl_{2}$/$CF_{4}$/Ar plasma. The maximum etch rate was 1060 $\AA\textrm{m}$/min in $Cl_{2}$/$CF_{4}$/Ar (80). The chemical reactions on the etched surface were studied with x-ray photoelectron spectroscopy. The etching of SBT thin films in $Cl_{2}$/$CF_{4}$/Ar were etched by chemically assisted reactive ion etching. The small addition of $Cl_2$ into $CF_4$(20)/Ar(80) plasma will decrease the fluorine radicals and the increase Cl radical.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.175-175
• /
• 2010

The etching characteristics with etch rate of ITO thin films in an $O_2/BCl_3$/Ar plasma were investigated. The etch rate of ITO thin films increased with increasing $O_2$ content from 0 to 10 % in $BCl_3$/Ar plasma, whereas that of ITO decreased with increasing $O_2$ content from 10 % to 30 % in $BCl_3$/Ar plasma. The maximum etch rate of 65.9 nm/min for the ITO thin films was obtained at 10 % $O_2$ addition. The etch conditions were the RF power of 500 W, bias power of 200 W, and process pressure of 2 Pa. The analysis of x-ray photoelectron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of ITO thin films and etch species.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.935-938
• /
• 2011

The etching characteristics of ZnO and etch selectivities of ZnO to $SiO_2$ in $SF_6$/Ar plasma were investigated using Inductively-coupled-plasma (ICP). The maximum etch rates of ZnO were 6.5 nm/min at $SF_6$(50%)/Ar(50%), Source power (700 W), Bias power (250 W), Working pressure(8 mTorr). The etch rate of ZnO showed a non-monotonic behavior with increasing from 0% to 50% Ar fraction in $SF_6$/ Ar plasma. The plasma diagnostic were characterized using Optical Emission Spectroscopy (OES) analysis measurements.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.2
• /
• pp.90-94
• /
• 2015

In this study, the characterizations of oxide contact hole etching are investigated with C₄F₈/O₂/Ar and CH₂F₂/C₄F₈/O₂/ Ar plasma. As the percent composition of C₄F₈ in a C₄F₈/O₂/Ar mixture increases, the amount of polymer deposited on the etched surface also increases because the C_xF_y polymer layer retards the reaction of oxygen atoms with PR. Adding CH₂F₂ into the C₄F₈/O₂/Ar plasma increases the etch rate of the oxide and the selectivity of oxide to PR. The profile of contact holes was close to 90°, and no visible residue was seen in the SEM image at a C₄F₈/(C₄F₈+O₂) ratio of 58%. The changes of chemical composition in the chamber were analyzed using optical emission spectroscopy, and the chemical reaction on the etched surface was investigated using X-ray photoelectron spectroscopy.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.383-393
• /
• 2008

The etching mechanism of $ZrO_2$ thin films and etch selectivity over some materials in both $BCl_3$/Ar and $BCl_3/CHF_3$/Ar plasmas are investigated using a combination of experimental and modeling methods. To obtain the data on plasma composition and fluxes of active species, global (0-dimensional) plasma models are developed with Langmuir probe diagnostics data. In $BCl_3$/Ar plasma, changes in gas mixing ratio result in non-linear changes of both densities and fluxes for Cl, $BCl_2$, and ${BCl_2}^+$. In this work, it is shown that the non-monotonic behavior of the $ZrO_2$ etch rate as a function of the $BCl_3$/Ar mixing ratio could be related to the ion-assisted etch mechanism and the ion-flux-limited etch regime. The addition of up to 33% $CHF_3$ to the $BCl_3$-rich $BCl_3$Ar plasma does not influence the $ZrO_2$ etch rate, but it non-monotonically changes the etch rates of both Si and $SiO_2$. The last effect can probably be associated with the corresponding behavior of the F atom density.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.6
• /
• pp.449-453
• /
• 2003

Ferroelectric YMnO$_3$ thin films were etched with Ar/Cl$_2$ and CF$_4$/Cl$_2$ inductively coupled plasma (ICP). The maximum etch rate of YMnO$_3$ thin film was 300 $\AA$/min at a Ar/Cl$_2$ gas mixing ratio of 2/8, a RF power of 800 W, a DE bias of 200 V, a chamber pressure of 15 mTorr, and a substrate temperature of 30 $^{\circ}C$. From the X-ray photoelectron spectroscopy (XPS) analysis, yttrium etched by chemical reactions with Cl radicals assisted by Ar ion bombardments in Ar/Cl$_2$ plasma. In CF$_4$/Cl$_2$ plasma, yttrium are remained on the etched surface of YMnO$_3$ and formed of nonvolatile YF$_{x}$ compounds manganese etched effectively by chemical reactions with Cl and F radicals. From the X-ray diffraction (XRD) analysis, the (0004) diffraction peak intensity of the YMnO$_3$ thin film etched in Ar/Cl$_2$ plasma shows lower value than that in CF$_4$/Cl$_2$ plasma. It indicates that the crystallinty of YMnO$_3$ thin film is more easily damaged by the Ar ion bombardment than the changes of stoichiometry due to nonvolatile etch by-products.s.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1211-1214
• /
• 2005

One of the important problems in recent AC-PDP technology is high efficiency. In this research, we have been investigated electro-optical characteristics of MgO protective layer after radio frequency(RF) plasma treatment using Ar, $O_2$, and $H_2$ gases. The breakdown voltage order was $O_2$ > Ar > Nontreatment > $H_2$. Also, brightness order was $O_2$ > Ar > Non-treatment > $H_2$. In this experiment, the best result was obtained after $O_2-plasma$ treatment.