• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.267-273
• /
• 2009

Three types of structural intermetallic compounds, $Ni_3Al$, NiAl and TiAl, having each single phase structure without pores were produced by arc-melting process. Their sliding wear properties were investigated against a hardened tool steel. It was shown that the wear of the intermetallic compounds was hardly occurred against the hardened tool steel. TiAl compound showed the best wear resistance among them. In this case, wear was preferentially occurred on the surface of the hardened tool steel of the mating material which has higher hardness. It could be found that the wear mode on intermetallics without pores by arc-melting process was different from that on its porous layer coated on steel by combustion synthesis.

• 한국세라믹학회지
• /
• 제34권1호
• /
• pp.88-94
• /
• 1997

플라즈마 용사법(plasma spray method)으로 제작된 상용 가스 터빈 연소기의 finned segment의 열차폐용 코팅계, ZrO2-8wt%Y2O3 top coat/Ni-26Cr-5Al-0.5Y bond coat/Hastelloy X superalloy 기판에서 NiCrAlY bond coat의 산화 거동과 열피로 파괴에 대하여 조사하였다. 생성된 bond coat의 주산화물은 NiO, CrO2, Al2O3였다. ZrO2/bond coat계면에서 생성된 산화물의 분포는 고온에서의 사용 전에 이 계면 아래에 얇은 층의 Al2O3가없는 곳에서는 NiO 산화층 및에 Cr2O3와 Al2O3가 혼합된 형태를 나타내었다. 열피로에 의해 박리된 시편의 파면을 관찰한 결과, 파괴는 주로 ZrO2/산화층 계면보다 세라믹층내로 약간 치우쳐서 일어나지만, 산화층 내에서도 약간 일어남을 알 수 있었다.

• 한국분말재료학회지
• /
• 제9권3호
• /
• pp.161-166
• /
• 2002

Processing and properties of $Al_2O_3$ composites with Ni-Fe content of 10 and 15 wt% were investigated. Homogeneous powder mixtures of $Al_2O_3$/Ni-Fe alloy were prepared by the solution-chemistry route using $Al_2O_3$, $Ni(NO_3)_2{\cdot}6H_2O$ and $Fe(NO_3)_3{\cdot}9H_2O$ powders. Microstructural observation of composite powder revealed that Ni-Fe alloy particles with a size of 20nm were homogeneously dispersed on $Al_2O_3$ powder surfaces. Hot-pressed composites showed enhanced fracture toughness and magnetic response. The properties are discussed based on the observed microstructural characteristics.

• 한국재료학회지
• /
• 제13권1호
• /
• pp.24-30
• /
• 2003

The Raney Ni catalyst was fabricated by mechanochemically process(MC process) in the Al-Ni system. Intermetallic compound obtained by mechanical alloying was leached in an alkaline solution. The characteristics of the mechanically alloyed powder and Raney Ni catalyst were analyzed by XRD, ICP-AES and EXAFS. In Al-50wt.%Ni, the metastable intermetallic compound phase close to AlNi phase was obtained by mechanical alloying unlike Al-Ni equilibrium phase diagram. The metastable intermetallic compound was transformed into $Al_3$$Ni_2$phase via the annealing at $750^{\circ}C$. The microstructure of Raney Ni fabricated by MC process was mainly bcc Ni including fcc Ni.

• 공업화학
• /
• 제8권3호
• /
• pp.382-388
• /
• 1997

본 연구는 펄스 반응기 및 고정층 연속반응기를 사용하여 ${\gamma}$-알루미나에 담지된 니켈촉매상에서 이산화탄소에 의한 프로판의 개질반응 특성을 고찰한 것이다 Ni/${\gamma}$-$A1_2O_3$촉매가 NiO/${\gamma}$-$A1_2O_3$촉매보다 $CO_2$의 해리능력과 프로판의 개질 능력이 우수한 것으로 나타났다. 프로판과 $CO_2$의 혼합물에 산소를 추가한 결과 프로판의 전환율이 증가하였고 표면의 탄소침적도 감소함을 알 수 있었다. Ni/${\gamma}$-$A1_2O_3$와 $Ga_2O_3$의 기계적 혼합 촉매는 Ni/${\gamma}$-$A1_2O_3$자체보다 촉매의 활성이 오래 유지되었고 두 상의 협동에 의한 상승효과(synergistic effect)가 관찰되었다.

• 한국전기전자재료학회논문지
• /
• 제21권11호
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• 한국재료학회지
• /
• 제25권2호
• /
• pp.95-99
• /
• 2015

$NiAl_2O_4$ nanoparticle was synthesized by a reverse micelle processing for inorganic pigment. $Ni(NO_3)_2{\cdot}6H_2O$ and $Al(NO_3)_3{\cdot}9H_2O$ were used for the precursor in order to synthesize $NiAl_2O_4$ nanoparticles. The aqueous solution, which consisted of a mixing molar ratio of Ni/Al, was 1:2 and heat treated at $800{\sim}1100^{\circ}C$ for 2h. The average size and distribution of synthesized $NiAl_2O_4$ powders are in the range of 10-20 nm and narrow, respectively. The average size of the synthesized $NiAl_2O_4$ powders increased with an increasing water-to-surfactant molar ratio and heating temperature. The crystallinity of synthesized $NiAl_2O_4$ powder increased with an increasing heating temperature. The synthesized $NiAl_2O_4$ powders were characterized by X-ray diffraction analysis(XRD), a field emission scanning electron microscopy(FE-SEM), and a color spectrophotometer. The properties of synthesized powders were affected as a function such as a molar ratio and heating temperature. Results indicate that synthesis using a reverse miclle processing is a favorable process to obtain $NiAl_2O_4$ spinels at low temperatures. The procedure performed suggests that this new synthesis route for producing these oxides has the advantage of being fast and simple. Colorimetric coordinates indicate that the pigments obtained exhibit blue colors.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.769-774
• /
• 2002

금속 산화물 상태으 혼합분말을 수소 환원하여 $Al_2O_3$ 분말 표면에 20 nm 크기의 Fe-Ni 합금이 균일하게 분산된 복합분말을 합성하였다. 상압소결을 이용하여 제조한 $Al_2O_3$/Fe-Ni 나노복합재료는 전 소결 온도 범위에서 단지 $Al_2O_3$와 ${gamma}$-Fe-Ni 상만으로 구성되어 있었고, $1350^{\circ}C$ 이상의 소결 온도에서 98% 이상의 치밀화를 이루었다. 최대 파괴강도와 파괴인성은 각각 574 MPa과 3.9 MP$a{\cdot}m1/2$로서 동일한 소결 조건의 순수 $Al_2O_3$ 보다 약 20% 증가하였다. 나노복합재료는 강자성 거동을 보였으며 분산상의 평균 입자 크기가 감소함에 따라 증가된 보자력 값을 나타내었다.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.506-513
• /
• 2010

The composite coatings of $(ZrO_2-8Y_2O_3)$/(Ni-22Cr-10Al-1Y) were prepared by the air plasma spraying method. They consisted of (Ni,Cr)-rich regions,$(ZrO_2-Y_2O_3)$-rich regions, and $Al_2O_3$-rich regions that were formed by oxidation of Al from (Ni-22Cr-10Al-1Y) during spraying. The coatings corroded at 800 and $900^{\circ}C$ in NaCl-$Na_2SO_4$ molten salts up to 50 hr. Ni, Cr and Al oxidized to NiO, $Cr_2O_3$ and ${\alpha}-Al_2O_3$, respectively. These oxides and $(ZrO_2-Y_2O_3)$ were dissolved off into the molten salts during hot corrosion, which resulted in the ever-lasting corrosion of the composite coatings. Chromium diffused out from the (Ni,Cr)-rich regions and oxidized to $Cr_2O_3$, which was most frequently found as surface scales. Aluminum retained in the (Ni,Cr)-rich regions were similarly diffused out.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.726-731
• /
• 2002

Reaction synthesis is a process to form ceramics, intermetallics and their composites from elemental powder mixture. Application of this process to a surface modification techniques has a possibilities to enable the process at a lower temperature or for a shorter time, although synthesized materials are likely to include voids and unreacted elements. This paper intend to examine the effect of Si addition to the mixture of Al and Ni on the densification of synthesized Ni-Al intermetallic compounds and to evaluate the surface properties of obtained coatings. By the Si addition, exothermic reaction temperature to form Ni-Al intermetallic was lowered to be below the melting point of Al. Si soluted $Al_3$Ni$_2$, $Al_3$Ni and $Al_{6}$Ni$_3$Si were mainly formed in the coating layer when powder mixture was heated to 973K for 300s. Besides, densification was enhanced by increasing hot press pressure, Si additions and heating rate. When the composition of eutectic Al-Si reaches 78%, void ratio of sintered compact reduced to 0.4%. It is caused by higher flowability of Al-Si liquid phase generated and its infiltration into the void. Since the hardness of NiAl(Si) compound (about 600HV) formed in the coating layer is higher than that of Ni-Al compound (about 400HV), coating layer with high density and superior wear property is obtained by hot press using reaction synthesis from Al-Ni-Si powder mixture.