• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.208-208
• /
• 2003

저온균일침전법(HPPLT)으로 제조된 TiO$_2$나노분말은 10$0^{\circ}C$이하의 온도에서 rutile상을 얻을 수 있다. 또한, rutile에서 anatase로의 상변화는 합성시간, 가열속도, 반응온도 그리고 음이온 첨가에 의해 일어난다고 보고되어졌지만, 금속양이온들에 의한 상변화는 알려진 바가 없다. 따라서, 다양한 양이온을 첨가하여 저온균일침전법에서 TiO$_2$의 상변화가 어떻게 일어나는지를 조사하였다. 출발원료인 TIC1$_4$를 사용하여 가수분해하여 0.67M의 TiOCl$_2$을 얻었다. 얻어진 TiOCl$_2$ 수용액에 각각 0.01M의 금속염화물(ZrOCl$_2$, NiCl$_2$, CuCl$_2$, FeCl$_3$, AlCl$_3$ 그리고 NbCl$_{5}$)을 첨가한 후 반응기에 넣고 10$0^{\circ}C$에서 4시간동안 가열하였다 가열한 후 얻어진 침전물에 NaOH 수용액을 이용하여 PH 7-8로 중화한 후 증류수로 Cl$^{-}$이온이 제거될 때까지 충분히 세척하였다. 세척된 침전물을 105$^{\circ}C$에서 24h동안 건조하여 분말을 얻었고, rutile에서 anatase로의 상변화특성을 관찰하기 위하여 XRD, SEM, TEM, ICP 분석을 실시하였다.

• Korean Journal of Environmental Agriculture
• /
• v.23 no.1
• /
• pp.15-21
• /
• 2004

Objectives of this study were to monitor the distribution of heavy metals, to compare extractable heavy metal with total content and to investigate the relationships between soil physico-chemical properties and heavy metals in orchard soil. Sampling sites were 48 in Gyeonggi, 36 in Gangwon, 36 in Chungbuk, and 44 in Chungnam, Soils were collected farm form two depths, 0 to 20 and 20 to 40 cm (here after referred to as upper and lower layers) from March to May in 1998. Total contents of heavy metal in soils were analyzed by ICP-OES after acid digestion ($HNO_3$:HCl:$H_2O_2$) whereas extractable contents were measured after successive extraction of 0.1N-HCl, 0.05 M-EDTA, and 0.005 M-DTPA. Mercury was analysed by mercury atomizer. The average contents of Cd Cu, and Pb in the extractant with 0.1N-HCl at upper layer were 0.080, 4.23, and 3.42 mg/kg, respectively. As content in the extractant with 1N-HCl was 0.44 mg/kg, and total contents of Zn, Ni and Hg were 78.9, 16.1, and 0.052 mg/kg, respectively. The ratios of concentrations of heavy metals to threshold values (Cd 1.5, Cu 50, Pb 100, Zn 300, Ni 40, Hg 4 mg/ke in Soil Environmental Conservation Act in Korea (2001) were low in the range of $1/2.5{\sim}1/76.9$ in orchard soils. The ratios of extractable heavy metal to total content ranged $5.4{\sim}9.21%$ for Cd, $27.9{\sim}47.8%$ for Cu, $12.6{\sim}21.8$% for Pb, $15.8{\sim}20.3%$ for Zn, $5.3{\sim}6.3%$ for Ni, and $0.7{\sim}3.6%$ for Zn, respectively. Cu and Pb contents in 0.05 M-EDTA extractable solution were higher than those in the other extractable solution. Total contents of Cd, Ni and Ni in soils were negatively correlated with sand content but positively correlated with silt and clay contents. Ratios of extractable heavy metal to total content were negatively correlated with clay content but ai and Ni contents were positively correlated with soil pH, organic matter, and available phosphorous. Therefore, the orchard soil was safe because the heavy metal contents of orchard soil were very low as compared to its threshold value in the Soil Environmental Conservation Act. However, it need to consider the input of agricultural materials to the agricultural land for farming practices for assessment of heavy metals.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.551-554
• /
• 2002

As a general rule, the brazing process between cemented carbides and steel used by Silver (Ag) type brazing filler. The composition of Ag type filler were used Ag-Cu-Zn-Cd type filler mainly. But, the demand of Cadmium (Cd)-free in Ag type filler was raised recently. The reason why Cd-free in Ag brazing filler were occupied to vaporize as a CdO$_2$ when brazing process, because of Cd element was almost low boiling point of all Ag type filler elements. And, CdO$_2$ was a very harmful element for the human body. This experiment was developed Cd-freeing on Ag type filler that was used Indium (In) instead of Cd element. In this experiment, there were changed from 0 to 5% In addition in Ag brazing filler and investigated to most effective percentage of Indium. As a result, the change of In addition instead of Cd, there was a very useful element and obtained same property only 3% In added specimens compared to Cd 19% added specimens. These specimens were obtained same or more deflective strength. In this case, there were obtained 70 MPa over strength and wide brazing temperature range 650-800 C. A factor of deflective strength were influenced by composition and the shape of $\beta$ phase and between $\beta$ phase and cemented carbides interface. Indium element presented as $\alpha$ phase and non-effective factor directly, but it's occupied to solid solution hardening as a phase. $\beta$ phase were composed 84-94% Cu-Ni-Zn elements mainly. Especially, the presence of Ni element in interface was a very important factor. Influence of condensed Ni element in interface layer was increased the ductility and strength of brazing layer. Therefore, these 3% In added Ag type filler were caused to obtain a high brazing strength.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2005.09a
• /
• pp.193-196
• /
• 2005

Low resistance Ni thin films for using NiSi formation and metallization by atomic layer deposition (ALD) method have been studied. ALD temperature window is formed between $200^{\circ}C\;and\;250^{\circ}C$ with deposition rate of $1.25{\AA}$/cycle. The minimum resistance of deposited Ni films shows $4.333\;{\Omega}/\square$ on the $SiO_2/Si$ substrate by $H_2$ direct purging process. The reason of showing the low resistance is believed to be due to format ion of the $Ni_3C$ phase by residual carbon in Bis-Ni The deposited film exhibits excellent step coverage in the trench having 1(100 nm) : 16 (1.6 um) aspect ratio.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.327-332
• /
• 1999

The recovery activation energy, the order of reaction and the recovery rate constant were detemined by isochronal and isothermal annealing treatment to investigate the recovery behaviors of neutron irradiated Mn-Mo-Ni low alloy steels$(fluence: 2.3\times10^{19}ncm^{-2}, 553K, E\geq1.0 MeV)$. Vickers microhardness tests were conducted to trace the recovery behavior after heat treatments. The results were analyzed in terms of recovery stages, behavior of responsible defects and recovery kinetics. It was shown that recovery occurred through two annealing stages(stage I : 703-753K, stage n : 813-873K) with re$\infty$very activation energies of 2.5 eV and 2.93 eV for each stage I and n, respectively. From the comparison of unirradiated and irradiated isochronal anneal curves, a radiation anneal hardening(RAH) peak was identified at around 813K. Most of recovery have occurred during about 120 min irrespective of isothermal annealing temperatures of 743K and 833K. Recovery rate constants were determined to be $3.4\times10^{-4}min^{-1} and 7.1\times10^{-4}min^{-1}$ for stage I and II, respectively. The order of reaction was about 2 for both recovery stages. Comparing the obtained data with those of previously reported results on neutron irradiated Mn- Mo- Ni steels, the thermal recovery be­havior of the present material seems to occur by the dissociation of point defect clusters formed during irradiation, and by the recombination process of self-interstitials and vacancies from dissociated vacancy clusters.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.3
• /
• pp.133-140
• /
• 2018

This paper is concerned with the 2-D micostructure generation for $Ni-A{\ell}_2O_3$ dual-phase composite materials and the numerical analysis of mechanical characteristic of hierarchical models of microstructure which are defined in terms of the scale of microstructure. The microstructures of dual-phase composite materials were generated by applying the mathematical RMDF(random morphology description functions) technique to a 2-D RVE of composite materials. And, the hierarchical models of microstructure were defined by the number of Gaussian points. Meanwhile, the volume fractions of metal and ceramic particles were set by adjusting the level of RMD functions. The microstructures which were generated by RMDF technique are definitely random even though the total number of Gaussian points is the same. The randomly generated microstructures were applied to a 2-D beam model, and the variation of normal and shear stresses to the scale of microstructure was numerically investigated. In addition, through the crack analyses, the influence of RMDF randomness and Gauss point number on the crack-tip stress is investigated.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.7
• /
• pp.1965-1969
• /
• 2014

A new tetranuclear Mn(III) complex $[Mn^{III}{_4}(sae)_4({\mu}_3-O)({\mu}_{1,1}-N_3)(OH)(H_2O)_2]{\cdot}H_2O$ (1) ($H_2sae$ = 2-salicylideneamino-1-ethanol) has been synthesized by the reaction of $MnCl_2{\cdot}4H_2O$, $H_2sae$ and sodium azide in the mixed solvent of methanol, acetonitrile and water. The X-ray diffraction analysis shows that the four Mn(III) ions in complex 1 have a unique adamantine arrangement, whereas the coordination environment of each Mn(III) ions is different. Magnetic studies indicate that complex 1 manifests antiferromagnetic behaviors. The magnetic susceptibilities of complex 1 have been fitted by two magnetic models based on the suitable analysis of its magnetic structural topology.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.489-493
• /
• 2016

Scandia ($Sc2O_3$)-stabilized zirconia (ScSZ) electrolyte-supported symmetrical solid oxide electrolyzer cells (SOECs), in which lanthanum strontium cobalt ferrite (LSCF)-gadolinia ($Gd_2O_3$)-doped ceria (GDC) composite materials are used as both the cathode and anode, were fabricated and their high temperature steam electrolysis (HTSE) performance was investigated. Current density-voltage curves were obtained for cells operated in 10% $H_2O$/90% Ar at 750, 800, and $850^{\circ}C$. It was possible to determine the ohmic, cathodic, and anodic contributions to the total overpotential using the three-electrode technique. The HTSE performance was significantly improved in the symmetrical cell with LSCF-GDC electrodes compared to the cell consisting of an Ni-YSZ cathode and LSCF-GDC anode. It was found that the overpotential due to the LSCF-GDC cathode largely decreased and, at a given current density, the total cell voltage decreased, which resulted in the enhanced hydrogen production rate in the symmetrical cell.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.5
• /
• pp.245-248
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Ni/ITO (INI) multilayer films were deposited on the glass substrates with a reactive magnetron sputtering system without intentional substrate heating and then the influence of the Ni interlayer on the methanol gas sensitivity of ITO and INI film sensors were investigated. Although both ITO and INI film sensors have the same thickness of 100 nm, INI sensors have a sandwich structure of ITO 50 nm/Ni 5 nm/ITO 45 nm. The changes in the gas sensitivity of the film sensors caused by methanol gas ranging from 100 to 1000 ppm were measured. It is observed that the INI film sensors show the higher sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the INI film sensor have the potential to be used as improved methanol gas sensors.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.11
• /
• pp.1106-1110
• /
• 2000

New 14-membered tetraaza macrocycles 1,8-diallyl-3,5,7,7,10,12,14,14-octamethyl-1,4,8,11-tetraazacyclotetradecane $(L^2)$ and 1,8-bis(n-propyl)-3,5,7,7,10,12,14,14-octamethyl-1,4,8,11-tetraazacyclotetradecane $(L^3)$ have been prepared by direct react ion of 2,5,5,7,9,12,12,14-octamethyl-1,4,8,11-tetraazacyclotetradecane $(L^1)with$ allyl bromide or n-propyl bromide. The nickel(II) and copper(II) complexes of $L^2andL^3have$ been prepared. The macrocycles show high copper(II) selectivity against nickel(II) ion in methanol solutions containing water. The wavelengths (ca. 505 nm) of the d-d bands for the nickel(II) complexes are extraordinarily longer than those for the complexes of $L^1and$ other related di-N-alkylated 14-membered tetraaza macrocycles. Crystal structure of $[NiL^2](ClO4)_2$ shows that the average Ni-N bond distance $(1.992\AA)$ of the complex is distinctly longer than those of other related nickel(II) complexes. Effects of the N- and C-substituents on the properties of the macrocyclic compounds are discussed.