• Membrane and Water Treatment
• /
• v.8 no.5
• /
• pp.449-462
• /
• 2017

Direct treatment of municipal wastewater by forward osmosis (FO) process was evaluated in terms of water flux decline, reverse salt diffusion, pollutants rejection and concentration efficiency by using synthetic seawater as the draw solution. It was found that when operating in PRO mode (active layer facing the draw solution), although the FO membrane exhibited higher osmotic water flux, more severe flux decline and reverse salt diffusion was also observed due to the more severe fouling of pollutants in the membrane support layer and accompanied fouling enhanced concentration polarization. In addition, although the water flux decline was shown to be lower for the FO mode (active layer facing the feed solution), irreversible membrane fouling was identified in both PRO and FO modes as the water flux cannot be restored to the initial value by physical flushing, highlighting the necessity of chemical cleaning in long-term operation. During the 7 cycles of filtration conducted in the experiments, the FO membrane exhibited considerably high rejection for TOC, COD, TP and $NH_4{^+}-N$ present in the wastewater. By optimizing the volume ratio of seawater draw solution/wastewater feed solution, a concentration factor of 3.1 and 3.7 was obtained for the FO and PRO modes, respectively. The results demonstrated the validity of the FO process for direct treatment of municipal wastewater by using seawater as the draw solution, while facilitating the subsequent utilization of concentrated wastewater for bioenergy production, which may have special implications for the coastline areas.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.12
• /
• pp.1849-1857
• /
• 2007

The experiment was carried out using fistulated multiparous Holstein Friesian crossbred (75% Holstein Friesian and 25% Red Sindhi) dairy cows in their dry period fed on untreated rice straw to evaluate the nutritive value of local protein feed resources using the in sacco method and in vitro pepsin-pancreatin digestion. Experimental feeds were cottonseed meal (CSM); soybean meal (SBM); dried brewery's grains (DBG); palm kernel meal (PSM); cassava hay (CH); leucaena leaf meal (LLM). Each feedstuff was weighed into duplicate nylon bags and incubated in each of the two rumen fistulated cows for 0, 2, 4, 8, 16, 24, and 48 h. Rumen feed residues from bags of 16 h incubation were used for estimation of lower gut digestibility by the technique of in vitro pepsin-pancreatin digestion. Ruminal ammonia-nitrogen ($NH_3-N$) concentrations did not differ between treatments or time with a mean of 5.5 mg%. Effective degradability of DM of CSM, SBM, DBG, PSM, CH and LLM were 41.9, 56.1, 30.8, 47.0, 41.1 and 47.5%, respectively. Effective degradabilities of the CP in feedstuffs were 49.6, 59.2, 40.9, 33.5, 47.3 and 65.0% for the respective feedstuffs. The CP in vitro pepsin-pancreatin digestibility as ranked from the highest to the lowest were SBM, CSM, LLM, CH, DBG, PSM, respectively. The intestinal and total tract digestion of feedstuffs in the current study were relatively lower than that obtained from previous literature. The results of this study indicate that SBM and LLM were highly degradable in the rumen, while CH, CSM and DBG were less degradable and, hence resulted in higher rumen undegradable protein. Soybean meal and LLM could be used to improve rumen ecology whilst CH, CSM and DBG could be used as rumen by-pass protein for ruminant feeding in the tropics.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.6
• /
• pp.851-858
• /
• 2002

This study was conducted to determine effects of whole (intact), coarsely-ground (4 mm), finely-ground (1 mm), steam-flaked and steam-flaked-ground (1 mm) corns on in vitro and in situ DM digestibilities and also in vitro fermentation characteristics. After 48 h incubation, in vitro dry matter digestibilities of whole, steam-flaked, coarsely-ground, steam-flaked-ground, and finely-ground corns were 6.79, 61.68, 76.48, 85.72 and 90.31%, respectively. Steam-flaked-ground corn showed the highest digestibility until 24 h incubation (p<0.01). After 48 h incubation, pH of whole corn decreased with a small range. However the values of pH of other media significantly decreased (p<0.01). The gas productions of finely-ground and steam-flaked-ground corns were higher than those of the other corns (p<0.01). After 24 h incubation, $NH_3$-N concentration of finely-ground and steam-flaked-ground corns increased rapidly. Total VFA was the highest in finely-ground corn, followed by steam-flaked-ground, steam-flaked, coarsely-ground and whole corns. Incorporating steam-flaked corn resulted in the highest propionate concentration (p<0.01) and the lowest acetate : propionate value (p<0.05). Finely-ground corn showed the highest in situ DM digestibility throughout the incubation period (p<0.01), followed by coarsely-ground, steam-flaked and whole corns, respectively. Overall, DM of whole corn was merely digested in vitro as well as in situ.

• Journal of environmental and Sanitary engineering
• /
• v.23 no.1
• /
• pp.49-56
• /
• 2008

Foodwaste will be able to treat is 13,000 ton/day. $18{\times}10^{13}$ won/yr are wasted with the foodwaste treatment. As a result, the initial working condition. These are given as follows : On the 1st. week, the foodwaste of the 130 ton/week(digest sludge : input foodwaste = 20 : 1) is being put into a DRANCO system by the space of 2 day. On the 2nd week, the food waste of the 130 ton/week(5 day) is being put into a DRANCO system by the space of 2 day. On the 3rd week, the foodwaste of the 130 ton/week is being put into a DRANCO system by the space of 3day. On the 4th week, the foodwaste of the 350 ton/week is being put into a DRANCO system. After that time, increase the quantity than last week is 10%. Under steady-state working condition, the methane content of the biogas is more then 55%. The $NH_3-N$ content of the digest sludge is under 3,500ppm. The VFA content of the digest sludge is under 1,500ppm. The pH is more then 8. The TS content of the digest sludge is $18{\sim}22%$. The VS content of the digest sludge is under 65%.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.533-536
• /
• 2009

The gasification technology is a very flexible and versatile technology to produce a wide variety products such as electricity, steam, hydrogen, Fisher-Tropsch(FT) diesels, Dimethyl Ether(DME), methanol and SNG(Synthetic Natural Gas) with near-zero pollutant emissions. Gasification converts coal and other low-grade feedstocks such as biomass, wastes, residual oil, petroleum coke, etc. to a very clean and usable syngas. Syngas is produced from gasifier including CO, $H_2$, $CO_2$, $N_2$, particulates and smaller quantities of $CH_4$, $NH_3$, $H_2S$, COS and etc. After removing pollutants, syngas can be variously used in energy and environment fields. The pilot-scale coal gasification system has been operated since 1994 at Ajou University in Suwon, Korea. The pilot-scale gasification facility consists of the coal gasifier, the hot gas filtering system, and the acid gas removal (AGR) system. The acid gas such as $H_2S$ and COS is removed in the AGR system before generating electricity by gas engine and producing chemicals like Di-methyl Ether(DME) in the catalytic reactor. The designed operation temperature and pressure of the $H_2S$ removal system are below $50^{\circ}C$ and 8 kg/$cm^2$. The iron chelate solution is used as an absorbent. $H_2S$ is removed below 0.1 ppm in the H2S removal system.

• Journal of Korean Society on Water Environment
• /
• v.20 no.5
• /
• pp.457-465
• /
• 2004

The objective of this study is to evaluate the possibility to apply the Moving Bed Biofilm Reactor(MBBR) in the activated sludge treatment process with existing aerobic HRT. Optimal operation conditions were assumed according to the analysis of organic matter and nutrients removal efficiencies depending on loading variations. The process was operated under different conditions: RUN I(HRT=7.14hr, $I{\cdot}R=100%$), RUN II(HRT=6.22hr, $I{\cdot}R=100%$), RUN III(HRT=6.22 hr, $I{\cdot}R=150%$), RUN IV(HRT=6.22hr, $I{\cdot}R=200%$), the TBOD removal efficien cies are 88%, 88.5%, 94.6%, 97.6%, respectively. Overall TSS removal efficiency is 90%, and it is increasing in RUN IV. In the case of Nitrogen, the highest removal efficiency of 90% was observed in RUN III and RUN IV, Nitrification and Denitrification rates are 0.013-0.016kg $NH_3-N/kg$ Mv-d and 0.009-0.019kg $NO_3/kg$ Mv-d, respectively. Phosphorus removal efficiencies are 89.6% in RUN I, 91.5% in RUN II, 84.3% in RUN III, and 76.4% in RUN IV. The process under shorter SRT yields better performance in terms of phosphorus removal. It was noticed that to achieve the effluent phosphorus concentration ofless than 1mg/L and removal efficiency higher than 80%, SRT should not be longer than 10 days. Experimental result shows that HRT of 6.22 hours is suitable for this treatment process, and, as a result, the aerobic reactor including moving media and DO depletion tank have a sufficient effect to the process performance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.176-176
• /
• 2011

실리콘 질화막($Si_3N_4$)과 산화막($SiO_2$)은 반도체 소자를 구성하는 물질 중 가장 널리 사용되는 유전 또는 절연물질이다. 이러한 실리콘 산화막과 질화막은 적용할 소자에 따라 다양한 CVD나 ALD 공정을 기반으로 제조한다. 증착공정 개발에 있어 실리콘 증착소재가 성공여부를 결정하는 근간이 되며, 이는 실리콘 증착소재의 특성에 따라 증착된 산화막과 질화막의 물성이 크게 변하기 때문이다. 실리콘 증착소재 개발을 위해서 국내외 증착소재 합성업체가 노력을 기울이고 있지만 개발된 증착소재의 특성을 정확히 진단하기 위한 기술이 뒷받침되지 않아 개발 효율이 높지 않은 것이 현실이다. 한국표준과학연구원 내 진공기술센터에서는 이러한 실리콘 증착소재의 특성, 특히 반응성을 평가하기 위한 기술 및 시스템을 개발하고 이를 활용하고 있다. 본 연구에서는 적외선 분광법을 이용하여 개발된 증착소재의 기상 열적안전성 및 반응기체에 따른 반응성을 실시간으로 진단하였다. 반응기체로는 산화막을 증착하기 위해 가장 많이 사용되는 $H_2O$와 질화막을 증착하기 위해 가장 많이 사용되는 $NH_3$를 사용하였다. 각 반응기체의 유량별, 가스셀 온도, 압력 등의 반응조건의 변화에 따른 실리콘 증착소재의 반응성 및 안정성을 평가하고 기존에 양산용으로 소자제조에 사용되고 있는 증착소재와 비교평가를 수행하였다.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.4
• /
• pp.224-230
• /
• 2000

Garbon steel(SM35C) was gas nitrocarburized at $580^{\circ}C$ in $55%N_2-40%NH_3-5%CO_2$ mixed gas atmosphere, and then the steel was induction hardened at $850^{\circ}C$. The microstructure of gas nitrocarburized surface layer was observed by optical microscope and SEM. The phase analysis was carried out by X-ray diffraction method. The mechanical properties of gas nitrocarburized SM35C steel was evaluated by hardness, wear and fatigue test. The thickness of compound and diffusion layer were increased with increasing the gas nitrocarburizing time and the densest compound layer was obtained at 3 hours gas nitrocarburizing time. In case of 15sec induction hardening after gas nitrocarburizing, the surface hardness was decreased from 800Hv to 630Hv owing to the decomposition of compound layer, but wear resistance was increased because of increased hardness of diffusion layer. The fatigue strength of induction hardened steel after gas nitrocarburizing, $58kgf/mm^2$, was higher than $41.5kg/mm^2$ of gas nitrocarburized steel and $45kg/mm^2$ of induction hardened steel, respectively.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.5 no.5
• /
• pp.355-361
• /
• 2000

A recycling reactor system operated under sequential anoxic and oxic conditions for the treatment of swine wastewater has been developed, in which piggery slurry is fermentatively and aerobically treated and then part of the effluent is recycled to the pigsty. This system significantly removes offensive smells (at both the pigsty and the treatment plant), BOD and others, and may be cost effective for small-scale farms. The most dominant heterotrophic were, in order, Alcaligenes faecalis, Brevundimonas diminuta and Streptococcus sp., while lactic acid bacteria were dominantly observed in the anoxic tank. We propose a novel monitoring system for a recycling piggery slurry treatment system through the use of neural networks. In this study, we tried to model the treatment process for each tank in the system (influent, fermentation, aeration, first sedimentation and fourth sedimentation tanks) based upon the population densities of the heterotrophic and lactic acid bacteria. Principal component analysis(PCA) was first applied to identify a relationship between input and output. The input would be microbial densities and the treatment parameters, such as population densities of heterotrophic and lactic acid bacteria, suspended solids(SS), COD, NH$_4$(sup)+-N, ortho-phosphorus (o-P), and total-phosphorus (T-P). then multi-layer neural networks were employed to model the treatment process for each tank. PCA filtration of the input data as microbial densities was found to facilitate the modeling procedure for the system monitoring even with a relatively lower number of imput. Neural network independently trained for each treatment tank and their subsequent combined data analysis allowed a successful prediction of the treatment system for at least two days.

• Journal of Microbiology and Biotechnology
• /
• v.30 no.11
• /
• pp.1688-1696
• /
• 2020

Soil physical and chemical characteristics, soil potential denitrification rates (PDR), community composition and nirK-, nirS- and nosZ-encoding denitrifiers were studied by using MiSeq sequencing, quantitative polymerase chain reaction (qPCR), and terminal restriction fragment polymorphism (T-RFLP) technologies base on short-term (5-year) tillage field experiment. The experiment included four tillage treatments: conventional tillage with crop residue incorporation (CT), rotary tillage with crop residue incorporation (RT), no-tillage with crop residue retention (NT), and rotary tillage with crop residue removed as control (RTO). The results indicated that soil organic carbon, total nitrogen and NH₄⁺-N contents were increased with CT, RT and NT treatments. Compared with RTO treatment, the copies number of nirK, nirS and nosZ in paddy soil with CT, RT and NT treatments were significantly increased. The principal coordinate analysis indicated that tillage management and crop residue returning management were the most and the second important factors for the change of denitrifying bacteria community, respectively. Meanwhile, this study indicated that activity and community composition of denitrifiers with CT, RT and NT treatments were increased, compared with RTO treatment. This result showed that nirK, nirS and nosZ-type denitrifiers communities in crop residue applied soil had higher species diversity compared with crop residue removed soil, and denitrifying bacteria community composition were dominated by Gammaproteobacteria, Deltaproteobacteria, and Betaproteobacteria. Therefore, it is a beneficial practice to increase soil PDR level, abundance and community composition of nitrogen-functional soil microorganism by combined application of tillage with crop residue management.