• Bulletin of the Korean Chemical Society
• /
• v.13 no.2
• /
• pp.127-131
• /
• 1992

Changes in network structures of ${\alpha}-Nb_2O_5$ in the X MgO+(1-X) ${\alpha}-Nb_2O_5$ solid solutions occurring as the MgO doping level (X) was varied were investigated by means of infrared spectroscopy and X-ray analysis. X-ray diffraction revealed that all the synthesized specimens have the monoclinic structure. The FT-IR spectroscopy showed that the system investigated forms the solid solutions in which $Mg^{2+}$ ions occupy the octahedral sites in parent crystal lattice. Electrical conductivities were measured as a function of temperature from 600 to $1050{\circ}$ and $P_{O2}$ form $1{\times}10^{-5}$ to $2{\times}10^{-1}$ atm. The defect structure and conduction mechanism were deduced from the results. The $1}n$ value in ${\alpha}{\propto}{P_{O2}^{1}n}}$ is found to be -1/4 with single possible defect model. From the activation energy ($E{\alpha}$ = 1.67-1.73 eV) and the1/n value, electronic conduction mechanism is suggested with a doubly charged oxygen vacancy.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.3
• /
• pp.6-10
• /
• 2003

Silver nano-powder was added to Ma $B_2$ to make (Ag)$_{(x)wt.%}$(Mg $B_2$)$_{(l00-x)wt.%}$ (A $g_{x}$-Mg $B_2$) (10 $\leq$ x $\leq$ 50) composite superconductors to investigate the effect of the Ag nano-powder on the vortex pinning. Pellets made out of the mixed powder were put inside stainless steel tubes, which were sintered at 85$0^{\circ}C$ in Ar atmosphere. No impurity phase was identified for as-rolled samples. However, both the Mg $B_2$ and the A $g_{x}$-Mg $B_2$ composite pellets, when sintered, contain small amount of Mg $B_4$ and MgAg impurity phases. From the magnetization study, it was found that the flux pinning was improved in the high magnetic field region (> 3 T) only when 10w/o Ag was added to Mg $B_2$. The "two step" structures in ZFC M(T) curve gradually increased as the amount of Ag added increased. Pinning centers can be created by adding a suitable amount of Ag nano-powder which is not too large to increase the decoupling between the Mg $B_2$ grains.crease the decoupling between the Mg $B_2$ grains.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1234-1239
• /
• 1999

Electromagnetic wave asorbing properties of the $Ni_{0.5}-Zn_{0.4}-X_{0.1}{\cdot}Fe_2O_4$, where X was replaced by substitution elements Cu, Mg, Mn, have been studied. The structure, shape, size and magnetic properties of the $Ni_{0.5}-Zn_{0.4}-X_{0.1}{\cdot}Fe_2O_4$ were analyzed by XRD, SEM, VSM. The relative complex permittivity, permeability, and electromagnetic wave absorbing properties were measured by Network Analyzer. The structure, shape, size and magnetization value of the $Ni_{0.5}-Zn_{0.4}-X_{0.1}{\cdot}Fe_2O_4$ were found to be similar in spite of substitution elements. The coercive force and hysteresis-loss showed maximum value when Mg was substituted for X. The dielectric loss(${\varepsilon}_r"/{\varepsilon}_r'$) was found to be maximum value when Mn was substituted for X. Also the magnetic loss(${\mu}_r"/{\mu}_r'$} was found to be maximum with Cu substitution. The electromagnetica wave absorbing property of the $Ni_{0.5}-Zn_{0.4}-X_{0.1}{\cdot}Fe_2O_4$-Rubber composite with 4mm thickness was excellent as over - 40dB at 9GHz, and the $Ni_{0.5}-Zn_{0.4}-X_{0.1}{\cdot}Fe_2O_4$-Rubber composite with 8mm thickness was over-40dB at 2GHz. Those composites also showed superior microwave absorbing properties.

• Advances in materials Research
• /
• v.9 no.3
• /
• pp.171-187
• /
• 2020

The microstructural evolution of different compositions of Mg-Sn alloys (30%Sn-70%Mg, 40%Sn-60%Mg and 50%Sn-50%Mg) is studied at first to understand the changes observed with change in tin content and deformation conditions. The Mg₂Sn phase increases with increase in tin content and a significant substructure development is found in 50%Sn-50%Mg alloy. The above observation led to further deformation studies on Mg₂Sn based thermoelectric materials with higher tin percentage. The microstructure in terms of Electron backscatter diffraction (EBSD)measurements is studied in detail followed by the determination of thermoelectric properties i.e., Seebeck coefficient and electrical conductivity for both as cast and extruded Mg_(2+x)Sn-Ag alloys. The electrical conductivity of the extruded Mg_(2+x)Sn-.3wt%Ag {x =1} alloy was found to be more than its as cast counterpart while the Seebeck coefficient values remained almost the same.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.450.2-450.2
• /
• 2014

열전재료는 열-전기가 상호 가역적으로 변하는 재료로서, 최근 에너지 변환소재 분야에서 각광받고 있다. 열전재료의 특성 효율은 무차원 열전 성능지수(dimensionless figure of merit, $ZT={\alpha}2{\sigma}T/{\kappa}$)로 나타낼 수 있다. 여기서 ${\alpha}$는 제벡계수(Seebeck coefficient), ${\sigma}$는 전기전도도(electrical conductivity), ${\kappa}$는 열전도도(thermal conductivity), T는 Kelvin 온도를 나타낸다. 500 K에서 800 K까지의 중온 영역에서 우수한 열전특성을 보이는 $Mg_2X$ (X=Si, Ge, Sn)와 이들의 고용체는 성분원소가 독성이 없고, 매장량이 많아 친환경 열전 재료로 각광받고 있다. $Mg_2X$ 고용체 중 $Mg_2Si_{1-x}Ge_x$는 기존 $Mn_2Si$, $Mg_2Ge$, $Mg_2Sn$계 보다 더 우수한 열전 성능지수를 보인다. 다양한 제조 방법들이 시도되고 있으나, 조성설계 및 구조, 성능 조절의 어려움이 있고, Mg의 산화와 휘발 및 Mg, Si, Ge의 융점 차이가 크고 중력 편석과 반응하지 않은 원소들로 인해 제조가 상당히 어렵다. Sb가 도핑된 $Mg_2Si_{0.5}Ge_{0.5}Sb_y$ (y=0, 0.005, 0.01, 0.02, 0.03) 고용체를 고상반응으로 합성하고 진공열간 압축성형을 통해 성공적으로 제조하였다. 고용 상을 확인하기 위하여 X선 회절분석을 실시하였고, 고용체 형성과 도핑에 따른 전기적 특성변화를 평가하기 위해 Hall 효과를 측정하여 전자 이동특성을 분석하였고, 323~823 K까지 전기전도도, 제벡계수, 열전도도의 측정을 통해 열전 성능지수를 평가하였다.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.254-257
• /
• 2000

We report spectroscopic ellipsometric (SE) measurements on $Cd_{1-x}Mg_x/Te$ (0$\leq$x$\leq$0.43) films grown on GaAs substrate. When compared with previous bulk data, at first, current spectrum shows clear interference oscillations below $E_0$ band gap energy, which means the transparent characteristic of direct transition material below $E_0$ edge. It proves that the film samples used for this work have the most interrupted surface of high quality reported so far by SE. Secondly the best resolution of $E_2$-peak is observed, so we can report clear splitting of E$_2$and $E_0'$ band gap energies. We also performed the multilayer calculation necessary to remove this interference oscillations to observe $E_0'$ band gap energy of $Cd_{1-x}Mg_x/Te$ (x=0.23) film.

• Korean Journal of Materials Research
• /
• v.19 no.3
• /
• pp.125-131
• /
• 2009

In this report, the structural and optical properties of sol-gel derived $Mg_xZn_{1-x}O$ thin films upon changes in the composition and annealing temperature were investigated. The $Mg^{2+}$ content and the annealing temperature were varied in the range of $0{\leq}x{\leq}0.35$ and $400^{\circ}C{\leq}T{\leq}600^{\circ}C$, respectively. The films exhibited a hexagonal wurtzite structure of a polycrystalline nature. The optical transmittance exceeded 85% and the optical band gap of the film was tuned as high as 3.84 eV at a value of x = 0.35 (annealed at $400^{\circ}C$), which was evidently the maximum $Mg^{2+}$ content for the single-phase polycrystalline $Mg_xZn_{1-x}O$ thin films prepared in this experiment. The optical band gap and photoluminescence emission were tailored to the higher energy side while maintaining crystallinity without a significant change of the lattice constant.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.756-760
• /
• 2007

The $(1-x)Mg_4Ta_2O_9-xwt%TiO_2\;(x=5\sim20)$ microwave dielectric ceramics were prepared by solid-state reaction method and sintered at $1450^{\circ}C$. According to the X-ray diffraction data, the $Mg_4Ta_2O_9-xwt%TiO_2$ ceramics had main phase of $Mg_4Ta_2O_9$ and $MgTi_2O_5$ peaks were added by increasing of $TiO_2$ addition. Microwave dielectric properties of the $Mg_4Ta_2O_9-xwt%TiO_2$ ceramics were influenced by $MgTi_2O_5$ phase and properties of $TiO_2$. There was a little decrement of the quality factor from 116,800GHz of pure $Mg_4Ta_2O_9$ to 100,100GHz of 15wt% $TiO_2$ added one. But there was excellent improvement in temperature coefficient of the resonant frequency (TCRF) by addition of 15wt% $TiO_2$. The dielectric constant quality factor and TCRF of the $Mg_4Ta_2O_9-xwt%TiO_2$ ceramics sintered at $1450^{\circ}C$ were $13.08\sim16.41,\;45,000\sim165,410GHz,\;-24.82\sim+3.88ppm/^{\circ}C$, respectively, depending on the value of x. Simulated dielectric resonator (DR) with $Mg_4Ta_2O_9-15wt%TiO_2$ ceramics had the operating frequency of 11.97GHz and $S_{2,1}$ of -35.034dB.

• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.711-720
• /
• 2012

In this study, the effect of aging treatment on the microstructure and tensile properties of AZ61-xPd (x = 0, 1 and 2 wt%) alloys were investigated. The microstructure of as-cast AZ61-xPd alloys mainly consisted of ${\alpha}-Mg$, $Mg_{17}Al_{12}$ and $Al_4Pd$ phases. After solution treatment, most of the $Mg_{17}Al_{12}$ phases were dissolved into the Mg matrix. Thereafter, $Mg_{17}Al_{12}$ phases were finely formed and distributed near thermally stable $Al_4Pd$ phases and inside the grains through aging treatment at $220^{\circ}C$ during 88 hours. With the aging at $220^{\circ}C$, the peak aged AZ61-xPd alloys showed higher hardness than as-cast and solution treated AZ61-xPd alloys. In particular, the AZ61-1Pd alloy was optimized due to refined $Mg_{17}Al_{12}$ and $Al_4Pd$ phases. Further, the peak aging time was reduced with increasing Pd addition (>1 wt%). Tensile strength was increased by Pd addition at $25^{\circ}C$, $150^{\circ}C$, both as-cast and peak aged AZ61-xPd alloys. After aging treatment, room and high temperature tensile strength were increased more than the as-cast specimens. The AZ61-1Pd alloy especially showed the largest strength increase range. Elongation was decreased with addition Pd at $25^{\circ}C$ and $150^{\circ}C$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.04a
• /
• pp.47-48
• /
• 2007

본 실험에서는 MgO (99.999%)와 ZnO (99.999%)의 두가지 타겟을 사용한 RF co-스퍼터링법을 이용하여 p-type Si (100) 기판 위에 $Zn_{1-x}Mg_xO$ 박막을 증착 하였다. ZnO 타겟의 RF-power은 고정시키고 MgO 타겟의 RF-power를 조절함으로써 Mg 함량을 조절하였다. EDX분석을 통해 MgO RF-power의 증가에 따라 고용되는 Mg의 함량이 증가함을 알 수 있었다. 또한 MgZnO내 Mg 함량이 높아짐에 따라 c-축 격자상수가 감소하는 것을 XRD분석을 통해 알 수 있었고, MgO기반의 2차상은 형성되지 않았다. PL 측정을 통해 Mg함량이 증가 할수록 UV 영역의 파장의 강도는 감소하고 UV 파장의 위치는 blueshift되는 것을 관찰 할 수 있었다.