• Progress in Superconductivity and Cryogenics
• /
• 제6권2호
• /
• pp.29-34
• /
• 2004

The linear type flux pump aims to compensate a little bit decremental persistent current of the HTS magnet in NMR and MRI spectrometers. The flux pump mainly consists of DC bias coil, 3-phase AC coil and Nb foil. The persistent current in closed superconductive circuit can be easily adjusted by the 3-phase AC current, its frequency and the DC bias current. In the experiment, it has been investigated that the flux pump can effectively charge the current in the load coil of 543 mH for various frequencies in 18 minutes under the DC bias of 10 A and the AC of 5 $A_{rms}$. The maximum magnitudes of pumping current and load magnet voltage are 0.72 A/min and 20 ㎷, respectively. Based on simulation results by the FEM are proved to nearly agree with experimental ones.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.75-79
• /
• 2003

We studied InP etch results in high density planar inductively coupled $BCl_3$ and $BCl_3$/Ar plasmas. The investigated process parameters were ICP source power, RIE chuck power, chamber pressure and $BCl_3$/Ar gas composition. It was found that increase of ICP source power and RIE chuck power raised etch rate of InP, while that of chamber pressure decreased etch rate. Etched InP surface was clean and smooth (RMS roughness < 2 nm) with a moderate etch rate ($300\;{\sim}\;500\;{\AA}/min$) after the planar $BCl_3/Ar$ ICP etching. It may make it possible to open a new regime of InP etching with $CH_4/H_2$ - free plasma chemistry. Some amount of Ar addition (< 50%) also improved etch rates of InP, while too much Ar addition reduced etch rates of InP.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.333-343
• /
• 2000

An automatic guidance system for combine was designed to harvest paddy rice by following a predetermined path. The automatic guidance system consisted of DGPS to locate position of combine, a gyro sensor system to measure heading angle, ultrasonic sensors to detect obstacles, a hydraulic system, microcomputer as a controller, and I/O interface system. Hydraulic cylinders and valves were installed to control movement of the combine. The heading angle and the position of the combine, and ultrasonic measurements from edge were used as the inputs of the controller. The operating position of hydraulic cylinder was determined as output of the controller. The automatic guidance system was evaluated at the 45-m straight path by changing the posture of the combine. The average RMS errors were 14.0 cm without offset and 15.0 cm with 1-m offset. The DGPS provided accurate position information within the limited error to guide the combine in the field. The results showed that the automatic guidance system could guide the combine autonomously in the paddy field when the posture of the combine was changed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.80-84
• /
• 1996

This paper aims at reviewing the Possibility application over normal or abnormal, detection used by AE and the wear characteristics of grinding process. In this study, when diamond bur in dentistry with chosen grinding conditions were tuned at grinding. The variation of grinding resistance and hE signal is detected by the use of AE measuring system. The tests are carried out in accordance with diamond burs and workpiece; arcyl and bovine. According to the experiment results, the following can be expected; AE has the possibility to detect the state normality and abnormality. However, the grinding resistance measuring can find it difficult to detect it. It can be accurately excerpted from AE occurrence pattern in contact start point of diamond bur and bovine, grinding condition and derailment point. It is known that AE$\_$rms/ is well compatible with grinding resistance. According to the increase of the material removal rate, the specific energy of the diamond bur is inclined to decrease and the grinding resistance has a tendency to increase.

• Proceedings of the Korean Information Science Society Conference
• /
• 한국정보과학회 2006년도 한국컴퓨터종합학술대회 논문집 Vol.33 No.1 (C)
• /
• pp.229-231
• /
• 2006

본 논문은 한국원자력연구소 내에서 가동 중인 하나로 원자로의 방사선감시시스템 소프트웨어 개발에 있어서 속성기반설계를 적용한 사례를 소개한다. 본 논문에서 채택한 속성기반설계는 시스템의 기능요건 및 품질요건 도출, 이를 만족하기 위한 전술 설정, 설정된 전술에 근거하여 시스템 아키텍처 결정, 확정된 아키텍처를 구현 및 검증하는 과정으로 이루어진다. 하나로 방사선감시시스템의 개발요건으로부터 사용성, 가용성, 유지보수성. 호환성, 확장성 과 같은 품질속성을 추출하였으며, 개발 전술로는 이중화된 서버에 다수의 클라이언트가 연결되는 클라이언트-서버클러스터링 전술과 객체지향적 데이터 처리 및 디스플레이 설계 전술을 채택하였다. 단기간 내에 개발을 완수해야하는 방사선감시시스템 개발에 속성기반설계를 적용함으로써 보다 효율적으로 과제를 성공시킬 수 있었다.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전력기술부문
• /
• pp.282-285
• /
• 2001

In general, the PSS/E program based on RMS mathematical models is used for analyzing the steady state and transient stability phenomena of full-scale large power system. Whereas, the EMTDC program unlike PSS/E, studies the specific reduced small-scale power systems as a basis of instantaneous value mathematical models and used to analyze the Electro-Magnetic transient characteristics. The PSS/E provides various control models such as exciter, governor, PSS models and TGOV5 model but there are few control models in EMTDC. In this paper, we developed EMTDC model for TGOV5 of a steam turbine and boiler which represents governor action, main, reheat and low-pressure effects, including boiler effects. The EMTDC model is developed by examining PSS/E control block and using User Define Model(UDM) in addition to default.lib provided by EMTDC. We verify the correctness of developed TGOV5 model with PSS/E and EMTDC simulation results using Governor Step(GSTEP) method.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.71-74
• /
• 2001

In general, the PSS/E program based on RMS mathematical models is used for analyzing the steady state and transient stability phenomena of full-scale large power system. Whereas, the EMTDC program unlike PSS/E, studies the specific reduced small-scale power systems as a basis of instantaneous value mathematical models and used to analyze the Electro-Magnetic transient characteristics. The PSS/E provides various control models such as exciter, governor and PSS models, But there are few control models in EMTDC. In this paper, we developed EMTDC models for governor which have been applied in KEPCO system. The EMTDC models are developed by examining PSS/E control block and using User Define Model in addition to default.lib provided by EMTDC. we verify the correctness of developed governor models with PSS/E and EMTDC simulation results using Governor Step(GSTEP) method.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.276-278
• /
• 2001

In recent years, both electric utilities and end users have expressed their deep concerns about the quality of electric power. Especially, voltage sag which is one of power quality disturbance is very serious power quality problem on the power system. Voltage sag is a decrease to between 0.1 and 0.9 pu in rms voltage magnitude on the power system for durations from 0.5 cycles to 1 minute. These voltage sags are usually caused by fault conditions, overloads, and starting of large motors. The wavelet transform has attracted considerable attention in the field of power quality analysis recently. It has proved to be a powerful tool to study those transients that have time-localized information. In this paper, different types of voltage sags are simulated by using EMTP. This paper proposes the effective technique for voltage sag detection using wavelet transform.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• 제9권5호
• /
• pp.504-509
• /
• 1999

In-situ cleaning and subsequent silicon epitaxial film growth were performed in a load-locked reactor equipped with Hg-grid UV lamp and PBN heater to obtain the smooth and contaminant-free underlying surface and develop low-temperature epitaxial film growth process. The removals of organic and native oxide were investigated using UV-excited $O_2$ and $NF_{3}/H_{2}$, and the effect of the surface condition was examined on the quality of silicon epitaxial film grown at temperature as low as $750^{\circ}C$. UV-excited gas phase cleaning was found to be effective in removing the organic and native oxide successfully providing a smooth surface with RMS roughness of 0.5$\AA$ at optimal condition. Crystalline quality of epitaxial film was determined by smoothness of cleaned surface and the presence of native oxide and impurity. Crystalline defects such as dislocation loops or voids due to the surface roughness were observed by XTEM.

• Journal of the Korean Chemical Society
• /
• 제14권4호
• /
• pp.327-332
• /
• 1970

A simple and convenient device for deflection-type direct reading the variations in electrolytic conductance is described and applied to the analysis of sulfur by combustion-$H_2O_2$ oxidation method. The apparatus consisted of a high resistance-ratio bridge in which the other adjacent arms are the differential cells. By adopting unusually high a-c voltage source for the bridge excitation, the a-c method for unbalanced bridge is established, decreased sensitivity owing to reduced bridge factor, 0.01, is overcome and also the absolute sensitivity and linearity are greatly improved. Over 50% variations in impedance of the balanced cell, within 1% deviation from the linearity can be attained with a volt (rms)order of output which was detected directly with VTVM without further amplification. Analysis of the bridge shows that these useful features are natural result of the constant current character of the high source impedance generator and the performance of the device agreed with the theoretical predictions. A standard procedure for the rapid analysis of sulfur using the bridge is also given, the analytical accuracy was approximately 1%. A determination takes not more than 5 minutes.